Smeg PX7502AU - Manuals

Instructions 7 EN • The settings for this domestic appliance are shown on the gas setting label. • This domestic appliance is not connected to a device for extracting combustion products. It must be installed and connected in accordance with current installation regulations. Pay particular attention...

Instructions 8 1.4 Disposal This appliance must be disposed of separately from other waste (Directives 2002/95/EC, 2002/96/EC, 2003/108/EC). The appliance does not contain substances in quantities sufficient to be considered hazardous to health and the environment, in accordance with current Europea...

Instructions 9 EN 1.7 How to read the user manual This user manual uses the following reading conventions: 1. Sequence of instructions for use.• Standalone instruction. Instructions General information on this user manual, on safety and final disposal. Description Description of the appliance and it...

Description 10 2 Description 2.1 General Description AUX: Auxiliary burner SR: Semi-rapid burner R: Rapid burner UR3: Ultra-rapid burner

Description 11 EN 2.2 Symbols Burners Burner off Burner at minimum setting Burner at maximum setting Cooking zones Front left Rear left Central Rear left Front right Burner knobs For lighting and adjusting the burners. Press and turn the knobs anti-clockwise to in order to light the relative burners...

Use 12 3 Use 3.1 Instructions Escaping gas may cause an explosion. If you smell gas or notice any faults in the gas installation:• Immediately shut off the gas supply or close the gas cylinder valve. • Immediately extinguish all naked flames and cigarettes. • Do not use any light or appliance switch...

Use 13 EN 3.2 First use 1. Remove any protective film from the outside or inside of the appliance, including accessories. 2. Remove any labels (apart from the technical data plate) from accessories. 3. Remove and wash all the appliance's accessories (see 4 Cleaning and maintenance). 3.3 Using the co...

Use 14 Correct positioning of the trivets There are concave silicone rests with a hole underneath the trivets that must be positioned on the relative fixing pins on the cooktop. Make sure that the trivets are simply centred on their respective burners, without forcing the burners to be raised or til...

Use 15 EN Practical tips for using the cooktop For better burner efficiency and to minimise gas consumption, use lidded pans of suitable size for the burner, so that flames do not reach up the sides of the pan. Once the contents come to the boil, turn down the flame enough to ensure that the liquid ...

Cleaning and maintenance 16 4 Cleaning and maintenance 4.1 Instructions 4.2 Cleaning the appliance To keep the surfaces in good condition, they should be cleaned regularly after use. Let them cool first. Ordinary daily cleaning Always use specific products only that do not contain abrasives or chlor...

Cleaning and maintenance 17 EN Igniters and thermocouples For correct operation the igniters and thermocouples must always be perfectly clean. Check them frequently and clean them with a damp cloth if necessary. Remove any dry residues with a wooden toothpick or a needle. Flame-spreader crowns and b...

Installation 18 5 Installation 5.1 Minimum clearance to combustible surface Cook top A 200mm (Vertical combustible surface) measured form the edge of the nearest burner. B 600mm (Overhead) measured form the highest part of the highest surface and 750mm for an exhaust fan. C 50mm (non-combustible sur...

Installation 19 EN This appliance is suitable for connection with rigid pipe or flexible hose. The isolating manual shut-off valve connection point must be accessible when the appliance is installed.Flexible hose assembly must be certified to AS/NZS 1869 class B or D, be of appropriate internal diam...

Installation 20 5.4 Section cut from the work surface Create an opening with the dimensions shown in the figure in the work surface of the piece of furniture. Overall dimensions: gas and electrical connection location (measures in mm) View from the bottom G: Gas connection E: Electrical connection R...

Installation 21 EN 5.5 Mounting Over built-in oven unit The clearance between the cooktop and the kitchen furniture or other installed appliances must be enough to ensure sufficient ventilation and air discharge.If installed above an oven, a space must be left between the bottom of the cooktop and t...

Installation 22 Cooktop seal To prevent leakage of liquid between the frame of the cooktop and the work surface, put the insulating seal provided in position before assembly.1. The seal should be applied to the outer perimeter of the cooktop, making sure that it does not extend beyond the edge of th...

Installation 23 EN 5.6 Fixing using brackets The figures below show the exact position of the holes to correctly attach the cooktop to the countertop using the brackets provided ( A ) Screw the fixing brackets ( A ) into the holes on the sides of the bottom casing to properly fasten the cooktop to t...

Installation 24 requires careful design by an authorised specialist, and must comply with the regulation distances and positions. After installation, the engineer must issue a certificate of compliance. Extraction of the combustion products The combustion products may be extracted by means of hoods ...

Installation 25 EN 1 Extraction using a hood 2 Extraction without a hood A Single natural draught chimney B Single chimney with extractor fan C Directly outdoors with wall- or window- mounted extractor fan D Directly outdoors through wall Air Combustion products Extractor fan 5.8 Adaptation to diffe...

Installation 27 EN Adjusting the minimum setting for natural gas Light the burner and turn it to the minimum position. Extract the gas valve knob and turn the adjustment screw next to the valve spindle (depending on the model) until a constant minimum flame is obtained.Refit the knob and make sure t...

Installation 28 Burner and injector specifications tables 5.9 Electrical connection General information Check the grid characteristics against the data indicated on the plate.The identification plate bearing the technical data, serial number and brand name is visibly positioned on the appliance.Do n...

Installation 29 EN Fixed connection Fit the power line with an omnipolar circuit breaker in compliance with installation regulations.The circuit breaker should be located near the appliance and in an easily reachable position. Connection with plug and socket Make sure that the plug and socket are of...