Smeg PV375NAU - Manuals

Instructions 7 EN • At the end of the installation, check for any leaks with a soapy solution, never with a flame. • Have the electrical connection performed by authorised technical personnel. • The appliance must be connected to earth in compliance with electrical system safety standards. • Use cab...

Instructions 8 materials near this appliance. • Do not spray aereosols in the vicinity of this appliance while it is on operation. • Do not use this appliance as a space heater. • Do not modify this appliance.• Do not place articles on or against this appliance. • Not suitable for use with aftermark...

Instructions 9 EN 1.7 How to read the user manual This user manual uses the following reading conventions: 1. Use instruction sequence.• Single use instruction. Instructions General information on this user manual, on safety and final disposal. Description Description of the appliance and its access...

Description 10 2 Description 2.1 General Description 60 cm 70 cm AUX = AuxiliarySR = Semi-rapidRR = Reduced rapid R1= Large rapidR2 = Medium rapid

Use 11 EN 2.2 Symbols Cooking zones Front left Rear left Central Rear right Front right Centre left Burner knobs Useful for lighting and adjusting the hob burners. Press and turn the knobs anti- clockwise to the value to light the relative burners. Turn the knobs to the zone between the maximum and ...

Use 12 3 Use 3.1 Instructions 3.2 First use 1. Remove any protective film from the outside or inside of the appliance, including accessories. 2. Remove any labels (apart from the technical data plate) from accessories. 3. Remove and wash all the appliance accessories (see 4 Cleaning and maintenance)...

Use 13 EN Correct positioning of the grids The grids over the burners must be positioned in parallel to the control panel, not perpendicular. Correct positioning of the flame-spreader crowns and burner caps Before lighting the hob burners, make sure that the flame-spreader crowns are correctly posit...

Cleaning and maintenance 14 4 Cleaning and maintenance 4.1 Instructions 4.2 Cleaning the appliance To keep the surfaces in good condition, they should be cleaned regularly after use. Let them cool first. Ordinary daily cleaning Always use only specific products that do not contain abrasives or chlor...

Cleaning and maintenance 15 EN encrustations. Dry them thoroughly and return them to the hob. Flame-spreader crowns and burner caps For easier cleaning, the flame-spreader crowns and the burner caps can be removed. Wash them in hot water and non-abrasive detergent. Carefully remove any encrustation,...

Installation 16 5 Installation 5.1 Minimum clearance to combustible surface Cook top A 200mm (Vertical combustible surface) measured form the edge of the nearest burner. B 600mm (Overhead) measured form the highest part of the highest surface and 750mm for an exhaust fan. C 50mm (non-combustible sur...

Installation 17 EN This appliance is suitable for connection with rigid pipe or flexible hose. The isolating manual shut-off valve connection point must be accessible when the appliance is installed.Flexible hose assembly must be certified to AS/NZS 1869 class B or D, be of appropriate internal diam...

Installation 18 5.4 Mounting Over built-in oven The distance between the hob and the kitchen furniture or other installed appliances must be enough to ensure sufficient ventilation and air discharge.If installed above an oven, a space must be left between the bottom of the hob and the top of the app...

Installation 19 EN Hob seal To prevent leakage of liquid between the frame of the hob and the work surface, place the adhesive seal provided along the entire outer edge of the hob before assembly. 5.5 Fixing brackets Screw the fixing brackets ( A ) into the holes on the sides of the bottom casing to...

Installation 20 Extraction of the combustion products The combustion products may be extracted by means of hoods connected to a natural draught chimney whose efficiency is certain or via forced extraction. An efficient extraction system requires precision planning by a specialist qualified in this a...

Installation 21 EN 3. Pull the knobs upwards to remove them. 4. Unscrew the burner rings using the supplied wrench. 5. Remove the top.

Installation 22 Burner and nozzle characteristics table Replacing nozzles 1. Unscrew screw A and push air regulator B as far as it will go. 2. Use a spanner to remove the nozzles C and install the new ones for the required gas supply, following the indications given in the relevant table (see “Burne...

Installation 23 EN flame should not go out. Repeat the operation on all gas taps. Adjusting the minimum setting for LPG Tighten the screw located at the side of the tap rod clockwise all the way. Lubricating the gas taps Over time the gas taps may become difficult to turn and get blocked. Clean them...

Installation 24 5.7 Electrical connection General information Check the grid characteristics against the data indicated on the plate.The identification plate bearing the technical data, serial number and brand name is visibly positioned on the appliance.Do not remove this plate for any reason.Perfor...