Smeg PGA96 - Manuals

Instructions for the user 9 4. USING THE HOB 4.1 Lighting the hob burners Before lighting the hob burners, check that the flame-spreader crowns arecorrectly in place with their respective burner caps, making sure that the holes 1 in the flame-spreaders are aligned with the plugs 3 and thermocouples ...

Instructions for the user 10 4.2 Practical tips for using the burners For better burner efficiency and to minimise gas consumption, use pans with aflat, smooth base and a lid that have a suitable size for the burner, thuspreventing the flames reaching the sides of the pan (see point “4.3 Cookwaredia...

Instructions for the user 11 5. CLEANING AND MAINTENANCE Before performing any operations requiring access to powered parts,disconnect the appliance from the power supply. NEVER USE A JET OF STEAM TO CLEAN THE APPLIANCE. WARNING: For your safety, before performing any cleaning orextraordinary mainte...

Instructions for the installer 12 6. POSITIONING IN THE COUNTER TOP The following operation requires building and/or carpentry work and musttherefore be carried out by a competent tradesman.Installation can be carried out on various materials such as masonry, metal,solid wood or plastic laminated wo...

Instructions for the installer 14 IMPORTANT: if the appliance is mounted on a unit, make sure that a separatingshelf is installed, as shown in the figure.If the appliance is instead on an oven installed under the hob, there is no needto install a separating shelf.If installed on top of an oven, the ...

Instructions for the installer 15 6.2 Clearances above and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances – (Measurement A)Range hoods and exhaust fans shall be installed in accordance with themanufacturer’s instructions. However, in no case shall the clearance bet...

Instructions for the installer 16 NOTES 1 Requirement 3 does not apply to a freestanding or elevated cooking appliance whichis designed to prevent flames or the cooking vessels from extending beyond theperiphery of the appliance. 2 The ‘cooking surface area’ is defined as that part of the appliance ...

Instructions for the installer 17 The manufacturer declines all responsibility for damage to persons or thingscaused by non-observance of the above prescriptions or by interference withany part of the appliance. If installed over an oven, make sure that the cables (oven and hob) follow theoptimal pa...

Instructions for the installer 18 6.6 Gas connection This appliance is suitable for installation withNatural Gas or ULPG (propane/butane). Refer topage 21 for the relevant burner pressure andappropriate injector sizes. When the appliance isto be connected to Natural Gas then the pressureregulator su...

Instructions for the installer 19 Installation with the flexible hose must be carried out so that the length of thepiping does not exceed 1.2 metres fully extended; make sure that the hoses donot come into contact with moving parts and that they are not crushed in anyway. 6.7 Connection to liquid ga...

Instructions for the installer 20 7. ADAPTATION TO DIFFERENT TYPES OF GAS Before carrying out the following operations, disconnect the appliance from thepower supply. The appliance is preset for natural gas NG at pressure of 1.0 kPa. In case ofoperation with other types of gas, the burner nozzles mu...

Instructions for the installer 21 7.2 Burner and nozzle characteristics table Burner ULPG – 2.75 kPa Nominal gas Consumption (MJ/h) Injector (mm) Auxiliary (1) 3.9 0.54 Semi-rapid (2) 6.3 0.68 UR2 (3) 15.2 0.94 + 0.46 Burner NG – 1.0 kPa Nominal gas Consumption (MJ/h) Injector (mm) Auxiliary (1) 3.9...

Instructions for the installer 22 8. FINAL OPERATIONS After making the adjustments described above, reassemble the appliance byfollowing in reverse the instructions reported in paragraph "7.1 Replacement ofthe cooking hob nozzles". After adjustment with a gas other than the preset one, repla...