Smeg P705ES - Manuals - manualsarea.com

Page 2 - Instructions for safe and proper use

Instructions for safe and proper use 19 1. Instructions for safe and proper use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS...

Page 3 - Instructions for the installer; Positioning of hob; Attachment to support structure

Instructions for the installer 20 2. Positioning of hob The following operation requires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they a...

Page 5 - Electrical connection

Instructions for the installer 22 3. Electrical connection Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same ...

Page 6 - Gas connection

Instructions for the installer 23 4. Gas connection If the appliance is installed on an oven, the gas pipe must not be passed along the back of the oven, as this may cause overheating. Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the prov...

Page 7 - Connection to LPG

Instructions for the installer 24 4.1 Connection to LPG Use a pressure regulator and make the connection to the tank according to the provisions of standards regulations in force. Make sure that feed pressure conforms to the levels shown in the table in Section “5.2 Regulation for LPG ”. 4.2 Ventila...

Page 8 - Adapting to different types of gas; Removing the hob

Instructions for the installer 25 5. Adapting to different types of gas Before performing any cleaning or maintenance work, detach the hob from the electrical socket. The hob has been inspected for G20 (2H) natural gas at a pressure of 20 mbar. For functioning with other types of gas the nozzles mus...

Page 9 - Regulation for LPG

Instructions for the installer 26 5.2 Regulation for LPG Loosen screw C and push air regulator D to the bottom. With a 7 mm wrench, remove nozzle E and replace it with the proper one (follow the instructions on the reference tables for the type of gas to be used). The torque wrench setting of the no...

Page 10 - Regulation of primary air; Reassembling the hob; Regulation of minimum for natural gas

Instructions for the installer 27 5.4 Regulation of primary air Referred to distance “ X ” in mm. BURNER G20 20 mbar G30/G31 28/37 mbar Auxiliary 4 open Semi rapid 3 2 Medium rapid 2 2.5 Large rapid 2 2.5 A 2 14 UR B 2 14 To identify the burners on your hob, refer to the drawings in point “5.8 Arran...

Page 11 - Regulation of minimum for LPG; Lubrication of gas taps

Instructions for the installer 28 5.7 Regulation of minimum for LPG To regulate the minimum for LPG, completely tighten (clockwise) the screw inside or next to the gas tap pin (depending on the model). The diameters of the by-passes for each burner are given in table “5.2 Regulation for LPG ”. After...

Page 12 - Instructions for the user; Description of controls; Front control panel

Instructions for the user 29 6. Description of controls 6.1 Front control panel All of the commands and controls for the hob are found on the front panel. MODEL 60 CONTROL PANEL MODEL 70 CONTROL PANEL MODEL 100 CONTROL PANEL DESCRIPTION OF THE KNOB The flame is lit by pressing the knob and simultane...

Page 13 - Using the hob; Burner lighting with safety device

Instructions for the user 30 7. Using the hob Check that the flame cap crowns, the burner caps and grids are correctly assembled. Pins A of the flame cap crowns must be inserted in housings B of the burner rings, and pins C on the grids must be blocked in their respective housings on the hob. 7.1 Bu...

Page 14 - Cleaning and maintenance; Cleaning the hob; Cleaning of components

Instructions for the user 31 8. Cleaning and maintenance Never use a steam jet to clean the appliance. Before any intervention, disconnect the power supply of the device. 8.1 Cleaning the hob To keep the hob in good condition, you should clean it after every use (after it has cooled). 8.1.1 Regular ...