Skylink 91558-01A - Manuals

Page 2 - RECEIVER INSTALLATION; Figure 1. Garage Door Opener Receiver, Back View; VEHICLE PREPARATION; NOTE; For ALL vehicles with main fuse:

RECEIVER INSTALLATION Kits 91558-01A and 91562-01 only 1. Unplug the power cord from the garage door drive unit toprevent door activation during installation. 2. Select an unswitched 110V power outlet in the garagelocated either highest in the garage, closest to the frontof the garage, or both. Plug...

Page 3 - TRANSMITTER INSTALLATION; Dyna Models; Proceed to the Harness Connection section.

For Dyna, Softail and Sportster models: When servicing the fuel system, do not smoke or allowopen flame or sparks in the vicinity. Gasoline is extremelyflammable and highly explosive, which could result indeath or serious injury. (00330a) 3. The fuel tank must be removed or slightly raised to access...

Page 5 - 004 and Later Sportster Models; FLHR Touring Models; FLHT, FLHX and FLTR Touring Models Trike Models

3 1 2 is06715 1. Transmitter mounting location 2. Wires to headlamp 3. Ignition module Figure 7. Transmitter Mounting and Wire Routing, (2003 or Earlier Sportster Models) 2004 and Later Sportster Models 1. Remove the fuel tank. See the correct section (Carburetedor EFI Engine) of the service manual....

Page 6 - 007 and Later V-Rod Models

1 5 6 2 3 4 is06718 1. Mount transmitter to fairing 2. Headlamp connector 3. Orange/white wire 4. Black wire 5. White wire 6. Yellow wire Figure 10. Wires for Transmitter Connections (FLTR) 2002-2003 V-Rod Models 1. See Figure 11. Remove the screw (3) fastening the frontleft louvered cover (1) to th...

Page 7 - HARNESS CONNECTION; General; For Touring and Trike models: Proceed to that section.; 011 and Later Softail Models; NOTES; Proceed to the Yellow and White Lead Connections; section for the specific model.; Touring and Trike Models; Yellow wire

HARNESS CONNECTION General Splicing of wire leads is necessary in the installation of thegarage door opener to the vehicle. Find the instructions for aspecific model in the sections that follow, and refer to the ser-vice manual appendix for proper wire splicing procedures. Be sure to follow manufact...

Page 8 - BLACK LEAD CONNECTION TO GROUND; On the engine near the starter on 2004 and later models.

1 2 3 is02055a 1. 1 into 1 splice 2. 2 into 1 splice 3. 3 into 1 splice Figure 15. Splice Configurations NOTE Electrical connectors are identified in the service manual bythe number and letter shown here within brackets. 4. Use the remaining red sealed splice connector to splicethe orange/white tran...

Page 10 - 003 and Earlier Softail Models

5. Pull only the orange/white wire out of the longer piece ofconduit on the garage door opener wire harness. Cut theexcess length from the orange/white wire to within easyreach of the adapter wire. 6. See Figure 15, the 1 into 1 splice configuration. Use ablue sealed splice connector (Figure 27, Ite...

Page 11 - White headlamp wire; 005 and Later V-Rod Models

NOTE On some Sportster models the ignition module must beremoved to access the orange/white wire in the main harness. 1. See Figure 20. Carefully slice open an area of the mainharness wrap inside the electrical side cover or under theseat at an accessible point, and cut an orange/white mainharness p...

Page 12 - Softail Models; Sportster Models

1 is06731 1. Headlamp connector [38] Figure 23. Wire Splice Locations (2005 and Later V-Rod) YELLOW AND WHITE LEAD CONNECTIONSTO HEADLAMP Dyna Models 1. See Figure 24. Use cable straps from the kit to fasten theremaining transmitter wires (yellow and white) and conduitto the motorcycle wires leading...

Page 13 - Install the front left louvered cover onto the motorcycle.

2 1 is06727 1. White and yellow headlamp wires 2. Cut headlamp wire casing to access wires Figure 25. White and Yellow Wire Optional External Splice Location (Sportster Models) 3. Cut the yellow and white wires in the headlamp housingseveral inches from the headlamp connector. Cut excesslength from ...

Page 14 - SET button; Release the SET button on the receiver.; TROUBLESHOOTING; With the ignition key switch turned to IGNITION:; Reset the Receiver; Unplug the receiver from the 110 Volt power outlet.

RECEIVER AND TRANSMITTERPROGRAMMING After the receiver and transmitter are installed, the receivermust be programmed to receive the transmitter frequency. Thisprocess may require two people, depending upon how far apartthe receiver and transmitter are during the programming pro-cess. NOTE Verify tha...

Page 15 - SERVICE PARTS; Figure 27. Service Parts, Remote Control Garage Door Opener Kits

SERVICE PARTS 2b 2a 3 8 6 4 1 7 5 14 10 11 15 13 12 9 is06735 Figure 27. Service Parts, Remote Control Garage Door Opener Kits Table 1. Service Parts, Garage Door Opener Kit 91558-01A Part Number Description (Quantity) Item Not sold separately Transmitter assembly 1 91650-01A Hardware kit (includes ...

Page 16 - Part Number

SERVICE PARTS Table 2. Service Parts, Transmitter Kit 91561-01 Part Number Description (Quantity) Item Not sold separately Transmitter assembly 1 91650-01 Hardware kit (includes items 3 through 9) 2b Not sold separately • Foam tape, double-sided, 1.0 inch (25.4 mm) x 1.5 inch (38.1 mm) 3 70585-93 • ...