Skylink G6K - Manual

1. INTRODUCTION

Model G6K

2. PROGRAM A KEYPAD TO THE GTR SMART BUTTON

TM

Refer to the section in the Skylink

®

model GTR to install the Smart Button

TM

and follow the instructions below to program the keypad transmitter.

Before proceeding, please remove the battery isolator from the keypad
transmitter.

The keypad transmitter can operate up to 4 Smart Button

TM

units, that also

means one keypad transmitter can operate up to 4 garage door openers.
Same PIN will be used for all doors. The factory default password is [0 0 0 0].

To operate door 1, you will enter [0 0 0 0][#][1]
To operate door 2, you will enter [0 0 0 0][#][2]
To operate door 3, you will enter [0 0 0 0][#][3]

To operate door 4, you will enter [0 0 0 0][#][4]

To program the keypad transmitter into the Smart Button

TM

, you must

decide which door you need to operate. If you only have one Smart
Button

TM

, we suggest you to use door 1. i.e. [0 0 0 0][#][1]. Follow the

instructions below to program the keypad transmitter.

4. REMOVE THE KEYPAD TRANSMITTER FROM THE SMART BUTTON

TM

Garage Door Remote Control

Garage Door
Remote Control
(Batteries inside)

1 pc 2.6 x 6 screw
1 pc 2.6 x 12 screw
1 pc 2.6 x 25 screw

Congratulations on your purchase of the Skylink

®

Garage Door Remote

Control Model G6K. The Model G6K works with the Skylink

®

Smart

Button

TM

. In this package, you will find a keyless entry transmitter with

3V lithium batteries and screws.

(a)

(c)

(b)

3. TROUBLE SHOOTING

Q: Door opener does not react after pressing the button on the keypad
transmitter?

A: - Ensure you hear 3 beeps from the keypad transmitter after entering

the default PIN [0 0 0 0][#][x] within 5 seconds, where x is the door
number. If you do not hear 3 beeps, that means the PIN you entered
is incorrect. Re-enter the correct PIN.

- Ensure the wires is successfully connected from the Smart Button

TM

to the wall mounted door control.

- Ensure the keypad transmitter has been programmed to the Smart

Button

TM

. Refer to section 2 for how to program a keypad to the

receiver.

You can delete the keypad transmitter(s) from the Smart Button

TM

,

first

delete all the remote controls, then learn the ones you would like to keep.

1. Press and hold the learn button for approx 10 seconds on the Smart

Button

TM

.

2. The LED will flash rapidly after 10 seconds to indicate all the pro-

grammed remote controls have been erased. You may now release
the learn button.

3. You have erased all the remote controls in the Smart Button

TM

.

5. CHANGE PIN

Follow the instructions below to change the PIN.
To change your PIN:

1.

Enter the current PIN, (factory default PIN 0 0 0 0), press * .

2.

Enter new 4 to 6 digit PIN, press * .

3.

Enter new PIN again, press * .

For example, if you are changing the PIN number from 0000 to 123456,
enter the following sequence, 0000, *, 123456, * , 123456, * .

If confirmed, the balcklit LED flashes and the unit emits a long beep.

Learn Button

6. BATTERY

Two 3 volt Lithium type (CR2032) batteries (included).

It is time to change the batteries when the backlight no longer appears.

+

-

Battery
Compartment

You can add up to 15 additional transmitters to control the
same receiver. Skylink

®

offers Keychain Transmitters and

Visor Transmitters to work with your receiver. For
more information, please visit our website at
www.skylinkhome.com or contact us.

7. ADDITIONAL TRANSMITTER

8. WARNING

DO NOT let children use the garage door transmitter without adult supervision.
Children can injure themselves or others by the garage door.

9. FCC

The Garage Door Remote Control is approved by the FCC and it complies with
Part 15 of the FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.

WARNING:

Changes or modifications to this unit not expressly approved by the party
responsible of compliance could void the user’s authority to operate the equipment.

10. WARRANTY

If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.

11. CUSTOMER SERVICE

If you would like to order Skylink’s product or have difficulty getting your Skylink
remote control to work, please :
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at [email protected], or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.

Fax (800) 286-1320

CUSTOMER SERVICE

17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com

P/N. 101Z489
® are registered trademarks of their respective corporations
©2007 SKYLINK GROUP

1. With the GTR Smart Button

TM

connected on your

existing wall button. The red light on the Smart
Button

TM

should flash after plugging in the power.

If the red light on the Smart Button

TM

is flashing

slowly, that indicates it is in standby mode.

2. Press the learn button on the side of the GTR.
3. Once the learn button is pressed, the red LED will

flash quickly. You may release the learn button.

4. Enter the default PIN [0 0 0 0][#][x] within 5

seconds, where x is the door number.

5. Once the keypad transmitter is programmed,

the red LED will flash slowly, in the same
way as it flashes in standby mode.

6. You can now mount the keypad transmitter

on a desired location.
Lift up the cover and insert screw above
the keypad in the slot provided (a). Remove
the battery cover and insert the second
screw in the lower slot (b). Tighten all
screws. Replace the battery cover, insert
and tighten screw (c).