Skylink GT-100 - Manual

Skylink GT-100 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Wall Console does not require any battery to operate and it can replace
most of the existing garage door opener’s push buttons. Garage Door
Sensor is battery operated and can be mounted on to the garage door by
double sided tape or screws. These 2 units operate wirelessly which
simplifies the installation.

Programming is very simple, you can select the time you would like the
door to be closed after it has been opened. The selectable door closing
times are 2 minutes, 5 minutes, 10 minutes and 20 minutes.

Garage Door
Monitor

Sensor

(Battery Included)
GS-101

2. INSTALLATION (CONT)

Before installing the Skylink

garage door closer, ensure your garage

door is equipped with an external entrapment protection device, such
as an infrared beam sensor which “sees” an object obstructing the door
without having actual contact with the object. A Garage door opener does
that not have the auto reversing mechanism should be replaced by one that
has the auto reversing mechanism f eature and the garage door clos er
must not be installed on garage a door opener without this feature.

Without a properly working safety reversal system, a person could be
seriously injured or killed by a closing garage door.

WARNING

2. INSTALLATION

Unplug the power cord of your garage door opener
before installation to ensure power is not connected.

WARNING

The installation involves 2 units:
1) Garage Door Monitor

Sensor

2) Wall Console

Garage Door Monitor

Sensor

Step 1 – Select a spot on your garage door to mount

the sensor

Before you install the sensor onto the garage door,
make sure the garage door is closed. The sensor
assembly should be mounted on one of the vertical
supports of your garage door near the bottom.

When the door is closed, the detection rod should be retracted. When
the door is open, the detection rod will be extended .

Note:
When the garage door is opening/closing,
make sure the sensor does not interfere with
the safety reversing sensor or safety beam
sensor supplied with your existing garage
door opener.

Step 2 – Mount the sensor on to your garage door

You can mount the sensor onto your garage
door with double-sided foam tape if the sur-
f ace of your garage door is smooth and clean
enough to provide a good adhesive surface,
such surf ace can usually be found on a me tal
garage door. Please ensure the surface is
smooth and clean.

Important: The bottom

o f t h e s e n s o r should be 1/2 inch above
the ground.

(Refer to Diagram A)

For w ooden garage doors, it is recommend ed
to mount the sensor with screws on to the
garage door with 3 x 18 screws provided.

4 Screws

Double-sided
foam tape

1/2 Inch

Note: Ensure you straighten up the antenna
on the rec eiver to receive the best possible
reception.

Diagram A

Wall Console

The GT-100R Wall Console replaces most garage door “push buttons” or
“wall consoles”. There are 2 different kinds of “push buttons”.

1) Single button

2) Multi-Function Wall Console

1) Single button

If your garage door opener equips with a single button “push button”,
you can replace the existing push button with Skylink

Garage Door

Closer Wall Console GT-100R. Please follow the procedures below.

1. Remove the existing push button by removing

the screws.

2. Disconnect the 2 wires that are connected to

the existing push button.

3. Connect these 2 wires to the 2 terminals on the

GT-100R Wall Console. Loosen the 2 screws
on the terminals, feed the 2 wires to the 2
terminals and tighten 2 screws to secure the
2 wires.

4. After connecting the 2 wires, the red LED under-

neath the push button will be on. The GT-100R
is now charging up. The GT-100R will be fully
charged when the buzzer emits a beep (approx
10 seconds to 1 minute depending on the brand
of garage door opener), the red LED will then
f lash slowly. The GT-100R is now ready to operate.

5. Mount the Wall Console to the wall with 2 screws.

6. Straighten up the antenna on the GT-100R.

Remove
existing
wires

One of
Vertical
Supports

Door closed

Door open

Remove the battery
isolator

4 pcs 3 x 18 screws
2 pcs 3.5 x 25 screws

Double-sided
foam tape

3V Lithium battery

Extension wires

Wall Console
GT-100R

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - minutes; Cancel Door Closer Delay Timer (when the timer is running); Door Closer Delay Timer

2) Multi-Function Wall Console Multi-Function Wall Console normally comes with 3 buttons that can be used to:1) operate the garage door opener lighting,2) lock the receiver so it doesn’t accept remote control operation, and3) push button for door opening / closing Depending on the brand of garage do...

Page 3 - Operation

Operation 3. OPERATION (CONT) Push Button Press the push button to open or close the garage door. Lock Button Lock feature is designed to prevent Skylink ® handheld remotes such as Skylink ® Keychain Remote Model 4B-201 (sold separately) to operate the garage door opener. To activate the lock featur...

Page 4 - CUSTOMER SERVICE

7. WARRANTY If, within one year from date of purchase, this pro duct should become defective(except battery), due to faulty workmanship or materials, it will be repaired orreplaced, without charge. Proof of purchase and a Return Authorization are required. This device complies with Part 15 of the FC...