Siemens T1000 - Manuals - manualsarea.com

Page 2 - Environmental conditions; fl

2/13 SPPA-T1000 System Overview Siemens CI 760 : 2006/2007 Input/ Output modules mounted in I/O stations serve as the interface to the process. These I/O stations communicate with the CC via PROFIBUS and other fi eld bus systems. Thus SoftAS acquires analog values and statuses from the process via t...

Page 3 - Closed Loop Control

3/13 SPPA-T1000 System Overview Siemens CI 760 : 2006/2007 It is recommended to observe in addition the following rules and guidelines in order to provide for a low-inductive functional compensation and a suf fi cient internal and external lightning protection:IEC 1024, Section 1 Internal and extern...

Page 5 - System Overview; Predictive control; State feedback controllers; Process

5/13 SPPA-T1000 System Overview Siemens CI 760 : 2006/2007 Predictive control Interdependencies in the process & disturbances in variables are integrated into fuzzy control design.Fuzzy logic controls are primarily used for the non-linear processes, which cannot be exactly represented in mathema...

Page 6 - SoftTurbo

6/13 SPPA-T1000 System Overview Siemens CI 760 : 2006/2007 is much better as compared to the conventional controllers as it reacts faster to the disturbances located at the beginning of the process.A number of fi rst order delay elements are set up and their outputs are connected to the controller a...

Page 7 - SoftFS - Fail Safe System; PROFIBUS; PROFIBUS Process Field Bus

7/13 SPPA-T1000 System Overview Siemens CI 760 : 2006/2007 ensure highest degrees of safety and availability.The SoftTurbo provides fl exibility to choose the con fi guration and the extent of redundancy in the most cost effective manner. SoftFS - Fail Safe System SoftFS is a unique Triple Modular R...

Page 8 - System Bus; Interfaces; GUES

8/13 SPPA-T1000 System Overview Siemens CI 760 : 2006/2007 System Bus This bus is used for communication between the individual participants. The participants on this bus can be: • SoftOM Servers/HMI • Central Controllers (CC) • GUES + Server/Client • Diagnostic Systems • Gateway Servers • OPC inter...

Page 9 - DAD; Field Interface Module

9/13 SPPA-T1000 System Overview Siemens CI 760 : 2006/2007 logics. It also integrates the entire hardware engi- neering of the I&C system. GUES + is a multi-user window-based engineering and commissioning tool. It provides a comprehen- sive technology environment right from project planning to t...

Page 10 - Non redundant system; Redundancy; The redundancy is explained by the following

10/13 SPPA-T1000 System Overview Siemens CI 760 : 2006/2007 large extent, the pre-commissioning checks. Connection between the FIM and I/O module is through a prefab plug-in cable. This reduces Installation and Commissioning times. • Possibility to interface higher voltage digital signals (e.g. 110V...

Page 11 - Fully redundant; I/O redundancy class is explained as follows:; The SoftOM redundancy is; Non redundant

11/13 SPPA-T1000 System Overview Siemens CI 760 : 2006/2007 Example 3 : It is the con fi guration in which the system bus and the terminal bus are redundant but the OM server is non-redundant. Example 4 : It is the con fi guration in which redundancy is at all levels i.e. terminal bus redundant, sys...

Page 13 - Engineering comfort

13/13 SPPA-T1000 System Overview Siemens CI 760 : 2006/2007 Secure investments SPPA-T1000 ensures that the investments on a Distributed Control System are secured against obsolescence of both hardware and software. The system can be seamlessly integrated into future technologies without the necessit...

Page 14 - SPP

SPPA-T1000 Typical system con fi guration Siemens CI 760 : 2006/2007 SPP A -T1000 Sy st em Con fi guration