Siemens Simatic S7-400 - Manuals

Preface v S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 System Documentation Package S7-400/M7-400 • S7-400, M7-400 Programmable Controllers; Hardware andInstallation • S7-400, M7-400 Programmable Controllers; Module Specifications • Automation System S7-400 CPU Data • ...

Preface vi S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Specific Information for S7-400 You require the following manuals and manual packages in order to program andcommission an S7-400: Manual/ Manual Package Contents Standard Softwarefor S7 and M7 STEP 7 BasicInform...

Preface vii S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Specific Information for M7-400 This documentation package describes the hardware of the M7-400. You will needthe following additional documentation for programming and starting up an M7-400: Documentation Conten...

Preface viii S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 A&D Technical Support Worldwide, available 24 hours a day: Johnson City Nuernberg Beijing Technical Support Worldwide (Nuernberg) Technical Support 24 hours a day, 365 days a year Phone: +49 (180) 5050-222 ...

Preface ix S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Service & Support on the Internet In addition to our documentation, we offer our Know-how online on the internet at: http://www.siemens.com/automation/service&support where you will find the following: • T...

xi S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Contents 1 General Technical Specifications 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Standards and Approvals 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Contents xii S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.12 Power Supply Module PS 405 4A; (6ES7405-0DA01-0AA0) 3-32 . . . . . . . . . . . 3.13 Power Supply Module PS 405 10A; (6ES7405-0KA00-0AA0) 3-34 . . . . . . . . . . 3.14 Power Supply Modules PS 405 10A; (6ES7...

Contents xiii S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.17 Digital Output Module SM 422;DO 16 24 VDC/2 A; (6ES7422-1BH11-0AA0) 4-62 . . . . . . . . . . . . . . . . . . . . . 4.18 Digital Output Module SM 422; DO 16 0-125 VDC/1.5 A; (6ES7422-5EH10-0AB0) 4-65 . . . ...

Contents xv S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 6 Interface Modules 6-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.1 Common Features of the Interface Modules 6-2 . . . . . . . . . . . . . . ....

Contents xvii S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13 Interface Submodules 13-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1 Interface Submodules Overview 13-2 . . . . . . . . . . . . . . . . . . . ....

Contents xix S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Figures 1-1 Power supply to the backup battery 1-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Structure of a Rack with 18 Slots 2-2 . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Contents xxiv S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Tables 1-1 Use in an Industrial Environment 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Products that Fulfill the Requirements of the Low-Voltage Directive 1-3 . . . . 1-3 Power...

1-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 General Technical Specifications What are General Technical Specifications? General technical specifications include the following: • The standards and test specifications complied with and met by the modules ofthe S7-40...

General Technical Specifications 1-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1.1 Standards and Approvals Note You will find the current approvals on the identification label of the respectiveproducts. IEC 61131-2 The S7-400/M7-400 programmable controller satisfie...

General Technical Specifications 1-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Low Voltage Directive The products listed in the table below fulfill the requirements of EU low-voltagedirective (73/23/EEC). Adherence to this EU directive was tested in accordancewith I...

General Technical Specifications 1-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Mark for Australia and New Zealand Our products satisfy the requirements of Standard AS/NZS 2064 (Class A). Note You will recognize the approval assigned to your product from the mark on...

General Technical Specifications 1-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 cuULu requirements on hazardous location on the battery power supply forCPUs The power supply to the backup battery of a CPU must be via a non–incendiveplug. The figure below portrays th...

General Technical Specifications 1-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Battery/Power supply CPU iput “Ext. Batt.” incl. cable Ca ≥ Ci + Cc (25nF + Cc) La ≥ Li + Lc (2mH + Lc) The batteries used must have the following properties: • Battery technology: Li/SOC...

General Technical Specifications 1-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 FM Approval Factory Mutual Approval Standard Class Number 3611, Class I, Division 2, GroupA, B, C, D. Temperature class: T4 at 60 ° C ambient temperature Exception: The following applies...

General Technical Specifications 1-9 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Safety Requirements for Installation The S7-400/M7-400 programmable controllers are “open type” equipment to theIEC 61131-2 standard and therefore adhere to the EU directive 73/23/EEC“Low...

General Technical Specifications 1-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Pulse-Shaped Interference The following table shows the electromagnetic compatibility of modules when thereare pulse-shaped disturbance variables. A requirement for this is that theS7-4...

General Technical Specifications 1-11 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Emission of Radio Interference Interference emission of electromagnetic fields in accordance with EN 55011: Limitvalue class A, Group 1. Table 1-6 Interference emission of electromagnet ...

General Technical Specifications 1-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Additional Measures If you want to connect an S7-400 or M7-400 system to the public power system,you must ensure compliance with limit value class B in accordance withEN 55022. Suitable...

General Technical Specifications 1-13 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Storing Backup Batteries Backup batteries must be stored in a cool, dry place. The maximum storage time is10 years. ! WarningImproper handling of backup batteries can cause injury and ma...

General Technical Specifications 1-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1.4 Mechanical and Ambient Climatic Conditions for Operating the S7-400/M7-400 Operating Conditions The S7-400/M7-400 is designed for weather-protected use as a permanentinstallation. T...

General Technical Specifications 1-15 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Table 1-11 Ambient Mechanical Conditions for the MSM 478 Mass Storage Module in Operation Frequency Range in Hz Test Values 10 ≤ f < 58 0.035 mm amplitude 10 ≤ f < 58 58 ≤ f < 5...

General Technical Specifications 1-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Table 1-13 Ambient Climatic Conditions for the S7-400 Climatic Conditions Remark Permitted Range Relative humidity Max. 95 % at +25 ° C No condensation,corresponds to RHstressing level ...

General Technical Specifications 1-17 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Ambient Climatic Conditions for the M7-400 The M7-400 may be used under the following ambient climatic conditions: Table 1-15 Ambient Climatic Conditions for the M7-400 Climatic Condi- t...

General Technical Specifications 1-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1.5 Information on Insulation Tests, Protection Class and Degree of Protection Test Voltages Insulation resistance was demonstrated in routine testing with the following testvoltages in...

General Technical Specifications 1-19 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 1.6 Using S7-400 in a zone 2 explosion–risk area You will find important information in different languages in the chapters below. Chapter overview Chapter Thema 1.6.1 Einsatz der S7-400...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications 1-20 A5E00069467-07 1.6.1 Einsatz der S7-400 im explosionsgefährdeten Bereich Zone 2 Zone 2 Explosionsgefährdete Bereiche werden in Zonen eingeteilt. Die Zonen werden nach der Wahrscheinlichkeit des Vorhan...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1-21 Instandhaltung Für eine Reparatur muss die betroffene Baugruppe an den Fertigungsort geschickt werden. Nur dort darf die Reparatur durchgeführt werden. Besondere Bedingungen 1. Die SIMA...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications 1-22 A5E00069467-07 1.6.2 Use of the S7-400 in a Zone 2 Hazardous Area Zone 2 Hazardous areas are divided up into zones. The zones are distinguished according to the probability of the existence of an expl...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1-23 Maintenance If repair is necessary, the affected module must be sent to the production location. Repairs can only be carried out there. Special Conditions 1. The SIMATIC S7-400 must be ...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications 1-24 A5E00069467-07 1.6.3 Utilisation du S7-400 dans un environnement à risque d'explosion en zone 2 Zone 2 Les environnements à risque d'explosion sont répartis en zones. Les zones se distinguent par la p...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1-25 Entretien Si une réparation est nécessaire, le module concerné doit être expédié au lieu de production. La réparation ne doit être effectuée qu'en ce lieu. Conditions particulières 1. L...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications 1-26 A5E00069467-07 1.6.4 Aplicación de la S7-400 en áreas con peligro de explosión, zona 2 Zona 2 Las áreas con peligro de explosión se clasifican en zonas. Las zonas se diferencian según la probabilidad ...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1-27 Mantenimiento Para una reparación se ha de remitir el módulo afectado al lugar de fabricación. Sólo allí se puede realizar la reparación. Condiciones especiales 1. El SIMATIC S7-400 se ...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications 1-28 A5E00069467-07 1.6.5 Impiego dell'S7-400 nell'area a pericolo di esplosione zona 2 Zona 2 Le aree a pericolo di esplosione vengono suddivise in zone. Le zone vengono distinte secondo la probabilità de...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1-29 Manutenzione Per una riparazione, l'unità interessata deve essere inviata al luogo di produzione. La riparazione può essere effettuata solo lì. Condizioni particolari 1. Il SIMATIC S7-4...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications 1-30 A5E00069467-07 1.6.6 Gebruik van de S7-400 in het explosief gebied zone 2 Zone 2 Explosieve gebieden worden ingedeeld in zones. Bij de zones wordt onderscheiden volgens de waarschijnlijkheid van de aa...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1-31 Instandhouding Voor een reparatie moet de betreffende module naar de plaats van vervaardiging worden gestuurd. Alleen daar mag de reparatie worden uitgevoerd. Speciale voorwaarden 1. He...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications 1-32 A5E00069467-07 1.6.7 Brug af S7-400 i det eksplosionfarlige område zone 2 Zone 2 Eksplosionsfarlige områder inddeles i zoner. Zonerne adskiller sig indbyrdes efter hvor sandsynligt det er, at der er e...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1-33 Vedligeholdelse Skal den pågældende komponent repareres, bedes De sende den til produktionsstedet. Reparation må kun udføres der. Særlige betingelser 1. SIMATIC S7-400 skal monteres i e...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications 1-34 A5E00069467-07 1.6.8 S7-400:n käyttö räjähdysvaarannetuilla alueilla, vyöhyke 2 Vyöhyke 2 Räjähdysvaarannetut alueet jaetaan vyöhykkeisiin. Vyöhykkeet erotellaan räjähdyskelpoisen ilmakehän olemassa o...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1-35 Kunnossapito Korjausta varten täytyy kyseinen rakenneryhmä lähettää valmistuspaikkaan. Korjaus voidaan suorittaa ainoastaan siellä. Erityiset vaatimukset 1. SIMATIC S7-400 täytyy asenta...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications 1-36 A5E00069467-07 1.6.9 Användning av S7-400 i explosionsriskområde zon 2 Zon 2 Explosionsriskområden delas in i zoner. Zonerna delas in enligt sannolikheten att en atmosfär med explosionsfara föreligger...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1-37 Underhåll Vid reparation måste den aktuella komponentgruppen insändas till tillverkaren. Reparationer får endast genomföras där. Särskilda villkor 1. SIMATIC S7-400 måste monteras i ett...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications 1-38 A5E00069467-07 1.6.10 Uso do S7-400 em área exposta ao perigo de explosão 2 Zona 2 As áreas expostas ao perigo de explosão são divididas em zonas. As zonas são diferenciadas de acordo com a probabilid...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1-39 Reparo Os componente em questão deve ser remetido para o local de produção a fim de que seja realizado o reparo. Apenas lá deve ser efetuado o reparo. Condições especiais 1. O SIMATIC S...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications 1-40 A5E00069467-07 1.6.11 Χρήση της συσκευής S7-400 σε επικίνδυνη για έκρηξη περιοχή , ζώνη 2 Ζώνη 2 Οι επικίνδυνες για έκρηξη περιοχές χωρίζονται σε ζώνες . Οι ζώνες διαφέρουν σύ µ φωνα µ ε την πιθανότητ...

General Technical Specifications S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 1-41 Συντήρηση Για µ ια επισκευή πρέπει να σταλθεί το αντίστοιχο δο µ ικό συγκρότη µ α στον τόπο κατασκευής . Μόνο εκεί επιτρέπεται να γίνει η επισκευή . Ιδιαίτερες προϋποθέσεις 1. To δο µ ι...

Racks 2-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Racks Chapter Overview Section Description Page 2.1 Function and Structure of the Racks 2-2 2.2 The Racks UR1; (6ES7400-1TA01-0AA0) and UR2; (6ES7400-1JA01-0AA0) 2-3 2.3 The Rack UR2-H; (6ES7400-2JA00-0AA0) 2-5 2.4...

Racks 2-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 2.1 Function and Structure of the Racks Introduction The racks in the S7-400 have the following tasks: • They hold the modules • They supply the modules with operating voltage • They connect the individual modules...

Racks 2-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 2.2 The Racks UR1; (6ES7400-1TA01-0AA0) and UR2; (6ES7400-1JA01-0AA0) Introduction The UR1 and UR2 racks are used for assembling central racks and expansionracks. The UR1 and UR2 racks have both an I/O bus and a co...

Racks 2-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Technical Specifications of the UR1 and UR2 Racks Rack UR1 UR2 Number of single-width slots 18 9 Dimensions W x H x D (in mm) 482.5 x 290 x 27.5 257.5 x 290 x 27.5 Weight (in kg) 3 4.1 as of version 03 1.5 2.15 as...

Racks 2-5 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 2.3 The Rack UR2-H; (6ES7400-2JA00-0AA0) Introduction The UR2-H rack is used for assembling two central racks or expansion racks inone rack. The UR2-H rack essentially represents two electrically isolated UR2racks ...

Racks 2-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 ! Caution Danger of damage to equipment. If you insert a power supply module in a slot that is not permitted for power supplymodules, the module may be damaged. Slots 1 to 4 are permitted, whereby powersupply modu...

Racks 2-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 2.4 The Rack CR2; (6ES7401-2TA01-0AA0) Introduction The CR2 rack is used for assembling segmented central racks. The CR2 has bothan I/O bus and a communication bus. The I/O bus is split into two local bussegments w...

Racks 2-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 2.5 The Rack CR3; (6ES7401-2TA01-0AA0) Introduction The CR3 rack is used for the assembly of CRs in standard systems (not infault-tolerant systems). The CR3 has an I/O bus and a communication bus. Suitable Modules...

Racks 2-9 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 2.6 The Racks ER1; (6ES7403-1TA01-0AA0) and ER2; (6ES7403-1JA01-0AA0) Introduction The ER1 and ER2 racks are used for assembling expansion racks. The ER1 and ER2 racks have only one I/O bus with the following restr...

Racks 2-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Structure of ER1 and ER2 465 mm 240 mm 482.5 mm 257.5 mm 290 mm 190 mm 40 mm 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 3 4 5 6 7 8 9 I/O bus I...

3-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Power Supply Modules Chapter Overview Section Description Page 3.1 Common Characteristics of the Power Supply Modules 3-2 3.2 Redundant Power Supply Modules 3-4 3.3 Backup Battery (Option) 3-6 3.4 Controls and Indicators...

Power Supply Modules 3-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.1 Common Characteristics of the Power Supply Modules Tasks of the Power Supply Modules The power supply modules of the S7-400 supply the other modules in the rack withtheir operating voltages via ...

Power Supply Modules 3-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Switching the Line Voltage Off/On The power supply modules have a making-current limiter in accordance withNAMUR. Power Supply Module in Invalid Slot If you insert the power supply module of a rack i...

Power Supply Modules 3-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.2 Redundant Power Supply Modules Order Numbers and Function Table 3-2 Redundant power supply modules Type Order Number Input Voltage Output Voltage See Section PS 407 10A R 6ES7407-0KR00-0AA0 85 V...

Power Supply Modules 3-5 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Characteristics The redundant power supply of an S7-400 has the following characteristics: • The power supply module delivers a making current in accordance withNAMUR. • Each of the power supply modu...

Power Supply Modules 3-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.3 Backup Battery (Option) Introduction The power supply modules of the S7-400 have a battery compartment for one ortwo backup batteries. Use of these batteries is optional. Function of the Backup ...

Power Supply Modules 3-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Backup Times The maximum backup time is based on the capacity of the backup batteries usedand the backup current in the rack. The backup current is the sum of all individualcurrents of the inserted b...

Power Supply Modules 3-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.4 Controls and Indicators Introduction The power supply modules of the S7-400 have essentially the same controls andindicators.The main differences are: • Not all the power supply modules have a v...

Power Supply Modules 3-9 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Meaning of the LEDs The meaning of the LEDs on the power supply modules is described in the tablesbelow. Section 3.5 contains a list of the faults indicated by these LEDs and noteson how to acknowled...

Power Supply Modules 3-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Battery Voltage on the Backplane Bus The battery voltage is either supplied by the backup battery or externally into theCPU or receive IM. In its normal state, the level of the battery voltage is b...

Power Supply Modules 3-11 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Function of the Operator Controls Table 3-6 Function of the operator controls of the power supply modules FMR momentary-contact pushbut-ton For acknowledging and resetting a fault indicator after co...

Power Supply Modules 3-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Cover The battery compartment, battery selector switch, voltage selector switch andpower connection are housed under one cover. The cover must remain closedduring operation in order to protect thes...

Power Supply Modules 3-13 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 3.5 Fault/Error Messages via LEDs Introduction The power supply modules of the S7-400 indicate module faults and backupbattery faults via LEDs on the front plate. Overview of the Fault/Error Message...

Power Supply Modules 3-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Table 3-8 INTF, DC5V, DC24V LEDs, continued LED INTF Remedy Cause of Fault DC24V DC5V H D* D Short circuit or overload on 5 V and24 V Check load on the power supplymodule. Possibly remove modules H...

Power Supply Modules 3-15 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 The following power supply modules will switch off in the event of a short circuit oroverload after 1 s to 3 s. The module will try to restart after no more than 3 s. If theerror has been eliminated...

Power Supply Modules 3-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 BAF, BATTF The following table applies to power supply modules with one battery if the BATTINDIC switch is in the BATT position. It shows the faults indicated and lists how toremedy the faults. Tab...

Power Supply Modules 3-17 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 BAF, BATT1F, BATT2F The following table applies to power supply modules with two batteries if the BATTINDIC switch is in the 1BATT position. It shows the faults indicated and lists how toremedy the ...

Power Supply Modules 3-19 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 3.6 Power Supply Module PS 407 4A; (6ES7407-0DA00-0AA0) Function The PS 407 4 A power supply module is designed for connecting to an AC linevoltage of 120/230 VAC and supplies 5 VDC/4 A and 24 VDC/0...

Power Supply Modules 3-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Technical Specifications of the PS 407 4A Programming Package Associated programmingpackage As of STEP7 V 2.0 Dimensions, Weight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight 25x290x217 0....

Power Supply Modules 3-21 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 3.7 Power Supply Module PS 407 4A; (6ES7407-0DA01-0AA0) Function The PS 407 4A power supply module is designed for connecting to either an ACline voltage of 85 to 264 V or a DC line voltage of 88 to...

Power Supply Modules 3-22 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Polarity Reversal of L+ and L- The polarity reversal of L+ and L- with supply voltages of between 88 VDCand 300 VDC has no effect on the function of the power supply. The connectionshould be made a...

Power Supply Modules 3-24 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Power Connection In contrast to the instructions on installing a power supply module described in the“S7-400, M7-400 Programmable Controllers, Hardware and Installation” manual,an AC connector is u...

Power Supply Modules 3-25 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Technical Specifications of the PS 407 10A and the PS 407 10A R Dimensions, Weight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight Cable cross-section 50x290x217 1.36 kg 3 x 1.5 mm 2 (litz wi...

Power Supply Modules 3-27 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Technical Specifications of the PS 407 20 A Programming Package Associated programmingpackage As of STEP7 V 2.0 Dimensions, Weight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight Cable cross-...

Power Supply Modules 3-30 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.11 Power Supply Module PS 405 4A; (6ES7405-0DA00-0AA0) Function The PS 405 4 A power supply module is designed for connecting to a DC linevoltage of 24 VDC and supplies 5 VDC/4 A and 24 VDC/0.5 A...

Power Supply Modules 3-31 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Technical Specifications of the PS 405 4 A Programming Package Associated programmingpackage As of STEP7 V 2.0 Dimensions, Weight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight 25x290x217 0....

Power Supply Modules 3-35 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Technical Specifications of the PS 405 10 A Programming Package Associated programmingpackage As of STEP7 V 2.0 Dimensions, Weight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight 50x290x217 1...

Power Supply Modules 3-36 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 3.14 Power Supply Modules PS 405 10A; (6ES7405-0KA01-0AA0) and PS 405 10A R; (405-0KR00-0AA0) Function The power supply modules PS 405 10A (standard) and PS 405 10A R (redundancy-capable, see Secti...

Power Supply Modules 3-39 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Technical Specifications of the PS 405 20 A Programming Package Associated programmingpackage As of STEP7 V 2.0 Dimensions, Weight, and Cable Cross-Sections Dimensions WxHxD (mm) Weight 75x290x217 2...

4-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Digital Modules Structure of the Chapter The present chapter is subdivided into the following subjects: 1. Overview containing the modules that are available here and a description 2. Information that is generally valid ...

Digital Modules 4-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.1 Module Overview Introduction The following tables summarize the most important characteristics of the digitalmodules. This overview is intended to make it easy to choose the suitable modulefor your ta...

Digital Modules 4-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Table 4-2 Digital Output Modules: Characteristics at a Glance Module Characte-ristics SM 422; DO 16 24 VDC/2 A (-1BH1x) SM 422; DO 16 20-125 VDC/1.5 A (-5EH10) SM 422; DO 32 24 VDC/ 0.5 A (-1BL00) SM 422...

Digital Modules 4-5 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.2 Sequence of Steps from Choosing to Commissioning the Digital Module Introduction The following table contains the tasks that you have to perform one after the otherto commission digital modules succes...

Digital Modules 4-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.3 Digital Module Parameter Assignment Introduction Digital modules can have different characteristics. You can set the characteristicsof dome modules by means of parameter assignment. Tools for Paramet...

Digital Modules 4-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.3.1 Parameters of the Digital Input Modules The parameterized digital input modules use a subset of the parameters andranges of values listed in the table below, depending on functionality. Refer to the...

Digital Modules 4-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.3.2 Parameters of the Digital Output Modules The parameterized digital output modules use a subset of the parameters andranges of values listed in the table below, depending on the functionality. Refer...

Digital Modules 4-9 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.4 Diagnostics of the Digital Modules Programmable and Non-Programmable Diagnostic Messages In diagnostics, we make a distinction between programmable andnon-programmable diagnostic messages. You obtain ...

Digital Modules 4-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Diagnostic Messages of the Digital Modules The table below gives an overview of the diagnostic messages for the digitalmodules with diagnostics capability. You can find out which diagnostic message each...

Digital Modules 4-11 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Causes of Errors and Remedial Measures for Digital Modules Table 4-9 Diagnostic Messages of the Digital Modules, Causes of Errors and RemedialMeasures Diagnostic Message Possible Error Cause Remedy Modul...

Digital Modules 4-13 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.5 Interrupts of the Digital Modules Introduction This section describes the interrupt behavior of the digital modules. The followinginterrupts exist: • Diagnostic Interrupt • Hardware interrupt Note th...

Digital Modules 4-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Hardware Interrupt A digital input module can trigger a hardware interrupt for each channel at a risingor falling edge, or both, of a signal status change. You perform parameter assignment for each chan...

Digital Modules 4-15 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.6 Input Characteristic Curve for Digital Inputs IEC 61131, Type 1 and Type 2 The IEC 61131 standard requires the following for the input current: • In the case of type 2, an input current of y 2 mA alr...

Digital Modules 4-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Input Characteristic Curve for Digital Inputs As long as the current flowing into the module remains v 1.5 mA, the module recognizes this as a “0” signal. 0.5 1.5 2 6 7 0 5 11 13 15 24 30 I min to IEC 6...

Digital Modules 4-17 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.7 Digital Input Module SM 421; DI 32 24 VDC (6ES7421-1BL00-0AA0) Characteristics The SM 421;DI 32 x 24 VDC is a digital input module with the following features: • 32 inputs, isolated in a group of 32....

Digital Modules 4-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Terminal Assignment and Block Diagram of the Digital Input Module SM 421;DI 32 x 24 VDC 123456789 10 11 12131415161718192021222324252627282930313233343536373839404142434445464748 1234567 L+ 0 M 1234567 ...

Digital Modules 4-19 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Technical Specifications of the SM 421; DI 32 x 24 VDC Programming package Associated programmingpackage As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Appro...

Digital Modules 4-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.8 Digital Input Module SM 421; DI 32 24 VDC; (6ES7421-1BL01-0AA0) Characteristics The digital input module SM 421; DI 32 24 VDC has the following features: • 32 inputs, isolated in a group of 32 • 24 ...

Digital Modules 4-23 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.9 Digital Input Module SM 421; DI 16 24 VDC; (6ES7421-7BH00-0AB0) Characteristics The digital input module SM 421; DI 16 24 VDC has the following features: • 16 inputs, isolated in 2 groups of 8 • 24 V...

Digital Modules 4-24 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Terminal Assignment and Block Diagram of the SM 421; DI 16 24 VDC INTF EXTF 1L+ 0 1 2 3 1Vs 4 5 6 7 1M 1M 2L+ 2L+ 0 1 2 3 2Vs 4 5 6 7 2M 2M 1L+ 2M 2L+ 1M M L+ 1L+ 1L+ 2L+ 1M 2M 2M 1M Backplane bus inter...

Digital Modules 4-25 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Terminal Assignment Diagram for Redundant Supply of Sensors The figure below shows how sensors can additionally be supplied by means of Vswith a redundant voltage source – for example, via another module...

Digital Modules 4-27 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.9.1 Assigning Parameters to the SM 421; DI 16 24 VDC Parameter Assignment You will find a description of the general procedure for assigning parameters todigital modules in Section 5.7. Parameters of t...

Digital Modules 4-28 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Ensuring a Wire Break Check Is Carried Out To ensure that a wire break check is carried out, you require an external sensorcircuit using a resistor of 10 to 18 k The resistor should be connected paralle...

Digital Modules 4-29 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.9.2 Behavior of the SM 421; DI 16 24 VDC Effect of Operating Mode and Supply Voltage on the Input Values The input values of the SM 421; DI 16 24 DC depend on the operating mode of the CPU and on the s...

Digital Modules 4-30 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Effect of Errors and Parameter Assignment on the Input Values The input values of the SM 421; DI 16 24 DC are affected by certain errors and the parameter assignment of the module. The following table l...

Digital Modules 4-31 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Behavior when the Input Delay Equals 0.1 ms and an Error Occurs If you have parameterized the following: • An input delay of 0.1 ms • KLV or SV as the response to an error • Substitute “1” In the event o...

Digital Modules 4-40 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Behavior when the Input Delay Equals 0.1 ms and an Error Occurs If you have parameterized the following: • An input delay of 0.1 ms or 0.05 ms • KLV or SV as the response to an error • Substitute “1” In...

Digital Modules 4-41 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.11 Digital Input Module SM 421; DI 16 120 VAC ; (6ES7421-5EH00-0AA0) Characteristics The SM 421; DI 16 120 VAC has the following features: • 16 inputs, isolated • 120 VAC rated input voltage • Suitable...

Digital Modules 4-42 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Terminal Assignment Diagram of the SM 421; DI 16 120 VAC 1234 0 Byte 0 56 1 78 2 9 10 3 11 13 1N 12 1415 4 1617 5 1819 6 2021 7 22 24 23 262728293031323334 36 35 383940414243444546 48 47 25 37 0 1 2 3 4...

Digital Modules 4-43 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Technical Specifications of the SM 421; DI 16 120 VAC Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx. 650 g Data for Specific Module Number of inputs 16 Length of cable ...

Digital Modules 4-46 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Technical Specifications of the SM 421; DI 16 24/60 VUC Programming package Associated programmingpackage As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight App...

Digital Modules 4-47 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.12.1 Assigning Parameters to the SM 421; DI 16 24/60 VUC Parameter Assignment You will find a description of the general procedure for assigning parameters todigital modules in Section 4.3. Parameters ...

Digital Modules 4-48 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Setting the Input Delay for Channel Groups You can only set the input delay for each group of channels. In other words, thesetting for channel 0 applies to inputs 0 to 7 and the setting for channel 8 ap...

Digital Modules 4-49 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Circuit as for active high or active low input ”1” ”0” 0V – L+ U_s ”1” U_s DI_x ”1” ”0” 0V L+ – L+ U_s DI_xN Channel x of the DI 421 16 x 24/60 VUC L+ U_s Input threshold Active high Active low Figure 4-...

Digital Modules 4-50 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.13 Digital Input Module SM 421; DI 16 120/230 VUC; (6ES7 421-1FH00-0AA0) Characteristics The SM 421; DI 16 120/230 VUC is characterized by the following features: • 16 inputs, isolated • Rated input v...

Digital Modules 4-56 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.15 Digital Input Module SM 421; DI 32 120 VUC ; (6ES7421-1EL00-0AA0) Characteristics The SM 421; DI 32 120 VUC is characterized by the following features: • 32 inputs, isolated • Rated input voltage 1...

Digital Modules 4-58 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Technical Specifications of the SM 421; DI 32 120 VUC Dimensions and Weight Dimensions W H D (mm) 25 290 210 Weight Approx. 600 g Data for Specific Module Number of inputs 32 Length of cable • Unshielde...

Digital Modules 4-59 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.16 Digital Output Module SM 422; DO 16 24 VDC/2 A; (6ES7422-1BH10-0AA0) Characteristics The digital output module SM 422; DO 16 24 VDC/2 A has the following features. • 16 outputs, isolated in two grou...

Digital Modules 4-60 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Terminal Assignment and Block Diagram of the SM 422; DO 16 24 VDC/2 A Data register and bus control LED control 123456789 11 12131415161718192021222324252627282930313233343536373839404142434445464748 1 ...

Digital Modules 4-61 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Technical Specifications of the SM 422; DO 16 24 VDC/2 A Programming package Associated programmingpackage As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight App...

Digital Modules 4-63 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Terminal Assignment and Block Diagram of the SM 422; DO 16 24 VDC/2 A Data register and bus control LED control 123456789 11 12131415161718192021222324252627282930313233343536373839404142434445464748 1 2...

Digital Modules 4-65 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.18 Digital Output Module SM 422; DO 16 20-125 VDC/1.5 A; (6ES7422-5EH10-0AB0) Characteristics The SM 422; DO 16 20-125 VDC/1.5 A has the following features: • 16 outputs, each channel is fused; reverse...

Digital Modules 4-66 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Terminal Assignment Diagram of the SM 422; DO 16 20-125 VDC/1.5 A 1234 0 Byte 0 56 1 78 2 9 10 3 11 13 L1+ 12 1415 4 1617 5 1819 6 2021 7 22 24 23 262728293031323334 36 35 383940414243444546 48 47 25 37...

Digital Modules 4-68 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Note If the power supply is switched on by means of a mechanical contact, a voltagepulse may occur at the outputs. The transient pulse lasts a maximum of 0.5 ms. Changing Fuses ! Warning This can result...

Digital Modules 4-69 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.18.1 Assigning Parameters to the SM 422; DO 16 20-125 VDC/1.5 A Parameter Assignment You will find a description of the general procedure for assigning parameters todigital modules in Section 5.7. Para...

Digital Modules 4-70 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.19 Digital Output Module SM 422; DO 32 24 VDC/0.5 A; (6ES7422-1BL00-0AA0) Characteristics The SM 422; DO 32 x 24 VDC/0.5 A has the following features: • 32 outputs, isolated in a group of 32 • Power i...

Digital Modules 4-71 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Terminal Assignment and Block Diagram of the SM 422; DO 32 24 VDC/0.5 A L+ 123456789 11 12131415161718192021222324252627282930313233343536373839404142434445464748 12 4 7 0 3 56 12 4 7 0 3 56 12 4 7 0 3 5...

Digital Modules 4-72 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Technical Specifications of the SM 422; DO 32 24 VDC/0.5 A Programming package Associated programmingpackage As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight ...

Digital Modules 4-77 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.20.1 Assigning Parameters to the SM 422; DO 32 24 VDC/0.5 A Parameter Assignment You will find a description of the general procedure for assigning parameters todigital modules in Section 5.7. Paramete...

Digital Modules 4-78 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 4.20.2 Behavior of the SM 422; DO 32 24 VDC/0.5 A Effect of Operating Mode and Supply Voltage on the Output Values The output values of the SM 422; DO 32 24 VDC/0.5 A depend on the operating mode of the...

Digital Modules 4-79 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.21 Digital Output Module SM 422; DO 8 120/230 VAC/5 A; (6ES7422-1FF00-0AA0) Characteristics The SM 422; DO 8 120/230 VAC/5 A has the following features: • 8 outputs, isolated in groups of 1 • Output cu...

Digital Modules 4-83 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.22 Digital Output Module SM 422; DO 16 120/230 VAC/2 A; (6ES7422-1FH00-0AA0) Characteristics The SM 422; DO 16 120/230 VAC/2 A has the following features: • 16 outputs, isolated in groups of 4 • 2 A ou...

Digital Modules 4-88 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Terminal Assignment Diagram of the SM 422; DO 16 20-120 VAC/2 A 1234 0 Byte 0 56 1 78 2 9 10 3 11 13 1L1 12 1415 4 1617 5 1819 6 2021 7 22 24 23 262728293031323334 36 35 383940414243444546 48 47 25 37 0...

Digital Modules 4-91 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 4.24 Relay Output Module SM 422; DO 16 30/230 VUC/Rel. 5 A; (6ES7422-1HH00-0AA0) Characteristics The SM 422; DO 16 30/230 VUC/Rel. 5 A has the following features: • 16 outputs, isolated in 8 groups of 2 ...

5-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Analog Modules Structure of the Chapter The present chapter is broken down into the following subjects: 1. Overview containing the modules that are available here and a description 2. Information that is generally availa...

Analog Modules 5-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.1 Module Overview Introduction The following tables summarize the most important characteristics of the analogmodules. This overview is intended to make it easy to choose the suitable modulefor your task...

Analog Modules 5-5 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Table 5-2 Analog Output Modules: Characteristics at a Glance Module SM 432; AO 8 13 Bit (-1HF00-) Characteristics Max. permissible common mode voltage Between the channels and the channelsagainst M ANA 3 V...

Analog Modules 5-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.3 Analog Value Representation Introduction This section describes the analog values for all the measuring ranges and outputranges which you can use with the analog modules. Converting Analog Values Analo...

Analog Modules 5-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Example In the following example you can see how the positions not padded with “0” arewritten for low resolution. Table 5-4 Example: Bit Pattern of a 16-Bit and a 13-Bit Analog Value Resolution Analog Val...

Analog Modules 5-9 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Table 5-5 Possible Resolutions of the Analog Values Resolution in Bits Units Analog Value in Bits Decimal Hexadecimal High-Order Byte Low-Order Byte 9 128 80 H 0 0 0 0 0 0 0 0 1 x x x x x x x 10 64 40 H 0 ...

Analog Modules 5-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Binary Representation of the Input Ranges The input ranges shown in Tables 5-6 to 5-8 are defined in two’s complementrepresentation: Table 5-6 Bipolar Input Ranges Units Measured Value Data Word Range Va...

Analog Modules 5-11 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Table 5-8 Life-Zero Input Ranges Units Measured Value Data Word Range Value in % 2 15 2 14 2 13 2 12 2 11 2 10 2 9 2 8 2 7 2 6 2 5 2 4 2 3 2 2 2 1 2 0 w 32767 w 118.515 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Ove...

Analog Modules 5-13 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Analog Value Representation in Current Measuring Ranges Table 5-12 Analog Value Representation in the Current Measuring Ranges ± 20 mA to ± 3.2 mA System Current Measuring Range Dec. Hex. ± 20 mA ± 10 mA ...

Analog Modules 5-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Table 5-14 Analog Value Representation in Current Measuring Ranges 4 to 20 mA System Current Measuring Range Dec. Hex. 4 to 20 mA 118.515% 32767 7FFF 22.96 mA Overflow 117.593% 32512 7F00 117.589% 32511 ...

Analog Modules 5-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog Value Representation for Themocouple Type B Table 5-22 Analog Value Representation for Thermocouple Type B Type B Units Type B Units Type B Units Type B in 5 C Deci- mal Hexa- deci- mal Type B in ...

Analog Modules 5-19 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Analog Value Representation for Thermocouple Type J Table 5-24 Analog Value Representation for Thermocouple Type J Type J Units Type J Units Type J Units Type J in 5 C Deci- mal Hexade- cimal Type J in 5 ...

Analog Modules 5-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog Value Representation for Thermocouple Type L Table 5-26 Analog Value Representation for Thermocouple Type L Type L Units Type L Units Type L Units Type L in 5 C Decimal Hexa- decimal Type L in 5 F...

Analog Modules 5-21 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Analog Value Representation for Thermocouple Types R, S Table 5-28 Analog Value Representation for Thermocouple Types R, S Types R S Units Types R Units Types R Units Types R, S in 5 C Deci- mal Hexa- dec...

Analog Modules 5-22 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog Value Representation for Thermocouple Type U Table 5-30 Analog Value Representation for Thermocouple Type U Type U Units Type U Units Type U Units Type U in 5 C Deci- mal Hexa- deci- mal Type U in...

Analog Modules 5-23 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.3.2 Analog Value Representation for Analog Output Channels Introduction The tables in this chapter contain the analog value representation for outputchannels of the analog output modules. The values in ...

Analog Modules 5-24 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Table 5-32 Unipolar Output Ranges Units Output Val e in Data Word Range Value in % 2 1 5 2 1 4 2 1 3 2 1 2 2 11 2 1 0 2 9 2 8 2 7 2 6 2 5 2 4 2 3 2 2 2 1 2 0 w 32512 0% 0 1 1 1 1 1 1 1 x x x x x x x x Ov...

Analog Modules 5-25 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Table 5-33 Life-Zero Output Ranges Units Output Val e in % Data Word Range Value in % 2 1 5 2 1 4 2 1 3 2 1 2 2 11 2 1 0 2 9 2 8 2 7 2 6 2 5 2 4 2 3 2 2 2 1 2 0 w 32512 0 % 0 1 1 1 1 1 1 1 x x x x x x x x...

Analog Modules 5-26 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Analog Value Representation in Voltage Output Ranges Table 5-34 Analog Value Representation in Output Range ±( 10 V System Voltage Output Range Dec. Hex. ±( 10 V 118.5149% 32767 7FFF 0.00 V Overflow, off...

Analog Modules 5-27 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Analog Value Representation in Current Output Ranges Table 5-36 Analog Value Representation in Output Range ±( 20 mA System Current Output Range Dec. Hex. ±( 20 mA 118.5149% 32767 7FFF 0.00 mA Overflow, o...

Analog Modules 5-28 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.4 Setting the Measuring Method and Measuring Ranges of the Analog Input Channels Two Procedures There are two procedures for setting the measuring method and the measuringranges of the analog input cha...

Analog Modules 5-29 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Replugging Measuring Range Modules If you want to replug a measuring range module, perform the following steps: 1. Use a screwdriver to ease the measuring range module out of the analog input module. Figu...

Analog Modules 5-30 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 2. Insert the measuring range module (correctly positioned (1)) into the analog input module. The measuring range selected is the one that points to marker point onmodule (2). 1 2 Figure 5-2 Inserting th...

Analog Modules 5-31 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.5 Behavior of the Analog Modules Introduction In this section, you will find information on: • How the analog input and output values depend on the operating modes of theCPU and the supply voltage of th...

Analog Modules 5-32 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Behavior on Failure of the Supply Voltage Failure of the load power supply L+ of the diagnostics-capable analog module isindicated in the case of parameterized two-wire transmitters by the EXTF LED onthe...

Analog Modules 5-33 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Effect of Range of Values on the Analog Output Module The behavior of the analog modules depends on where the output values lie withinthe value range. Table 5-40 Behavior of the Analog Output Modules as a...

Analog Modules 5-34 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Example of Determination of the Output Error of a Module An analog output module SM 432; AO 8 13 Bit is being used for voltage output. The output range “ " 10 V” is used. The module is operating at a...

Analog Modules 5-35 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.6 Conversion, Cycle, Setting and Response Time of Analog Modules Conversion Time of Analog Input Channels The conversion time consists of a basic conversion time and additional processingtimes of the mo...

Analog Modules 5-36 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Basic Execution Time of the Analog Input Channels The basic execution time corresponds to the cycle time for all the enabledchannels. Setting the Smoothing of Analog Values You can set the smoothing of t...

Analog Modules 5-37 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Example The following figure shows the number of module cycles for a step response afterwhich the smoothed analog value is approximately 100% applied, as a function ofthe smoothing that has been set. The ...

Analog Modules 5-38 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Basic Execution Time of the Analog Output Channels The basic execution time corresponds to the cycle time for all the enabledchannels. Tip You should disable any analog channels that are not being used t...

Analog Modules 5-39 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.7 Analog Module Parameter Assignment Introduction Analog modules can have different characteristics. You can set the characteristicsof the modules by means of parameter assignment. Tools for Parameter A...

Analog Modules 5-40 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.7.1 Parameters of the Analog Input Modules The analog input modules use a subset of the parameters and ranges of valueslisted in the table below, depending on the functionality. Refer to the section on...

Analog Modules 5-42 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.7.2 Parameters of the Analog Output Modules The analog output modules use a subset of the parameters and ranges of valueslisted in the table below, depending on the functionality. Refer to the section ...

Analog Modules 5-43 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.8 Connecting Sensors to Analog Inputs Introduction You can connect different sensors to the analog input modules depending on themeasuring method; voltage and current sensors, and resistors. This sectio...

Analog Modules 5-44 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Abbreviations and Mnemonics Used in the Figures Below The abbreviations and mnemonics used in the figures below have the followingmeanings: M +: Measuring line (positive) M –: Measuring line (negative) M...

Analog Modules 5-45 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Non-Isolated Sensors The non-isolated sensors are connected with the local ground potential (localground). When using non-isolated sensors, you must connect M ANA to chassis ground. Connecting Non-Isolate...

Analog Modules 5-46 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.9 Connecting Voltage Sensors Note The necessary connecting cables, which result from the potential connection of theanalog input module and the sensors, are not drawn in the figures shown below. In oth...

Analog Modules 5-47 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.10 Connecting Current Sensors Note The necessary connecting cables, which result from the potential connection of theanalog input module and the sensors, are not drawn in the figures shown below. In oth...

Analog Modules 5-48 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Connecting Two-Wire Transmitters +24 V Sensor, for example,pressure gauge +– L + M+M - M+M - M Two-wire transmitter Two-wire transmitter +– M P P M ANA * Connection required in the case of modules with M...

Analog Modules 5-49 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Connecting Four-Wire Transmitters M+M–M+M– M ANA Sensor, for example,pressure gauge +– Four-wire transmitter +– U H * Connection required in the case of modules with M ANA P P * * Figure 5-12 Connecting F...

Analog Modules 5-50 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.11 Connecting Resistance Thermometers and Resistors Note The necessary connecting cables, which result from the potential connection of theanalog input module and the sensors, are not drawn in the figu...

Analog Modules 5-51 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Four-Conductor Connection of a Resistance Thermometer The voltage generated at the resistance thermometer is measured via the M + and M – terminals. When you connect, watch out for the polarity of the con...

Analog Modules 5-52 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Three-Conductor Connection of a Resistance Thermometer During three-conductor connection to modules with 4 terminals per resistancethermometer, you must set up a jumper between M– and I C – and SE– and A...

Analog Modules 5-53 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.12 Connecting Thermocouples Design of Thermocouples A thermocouple consists of a pair of sensors and the necessary installation andconnecting parts. The thermocouple consists of two wires of dissimilar ...

Analog Modules 5-54 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Compensation of the Reference Junction Temperature There are several options for you to choose from for acquiring the referencejunction temperature in order to obtain an absolute temperature value from t...

Analog Modules 5-55 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Theory of Operation of Internal Compensation With internal compensation, you can establish the reference point across theterminals of the analog input modules. In this case, you must run the compensatingl...

Analog Modules 5-56 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Connection of Thermocouples without Compensation or Using the ReferenceTemperature Value Connect the thermocouples to the inputs of the module, either directly or by meansof compensating lines. Each chan...

Analog Modules 5-57 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Recommended Compensating Box We recommend you to use a comparison point (with integrated power supply unit)from Siemens as a compensating box. You will find the necessary ordering data inthe table below. ...

Analog Modules 5-58 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Connecting Thermocouples and Resistance Thermometers Connect the resistance thermometer to channel 0 of the module. Make sure thatyou parameterize the “RTD on Channel 0“ reference junction in STEP 7 for ...

Analog Modules 5-59 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.13 Connecting Loads/Actuators to Analog Outputs Introduction You can use the analog output modules to supply loads and actuators with currentand voltage. This section contains general information that i...

Analog Modules 5-60 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.14 Connecting Loads/Actuators to Voltage Outputs Connecting Loads to a Voltage Output Connecting loads to a voltage output is possible both in a four-conductor and atwo-conductor connection. Note The n...

Analog Modules 5-61 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 +24 V L + Q V S+ S– M ANA 0 V M U ISO Chassis ground R L Figure 5-21 Connecting Loads to a Voltage Output of an Isolated AO over aFour-Conductor Connection Two-Conductor Connection of Loads to a Voltage O...

Analog Modules 5-62 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.15 Connecting Loads/Actuators to Current Outputs Note The necessary connecting cables, which result from the potential connection of theanalog output module, are not drawn in the figures shown below. I...

Analog Modules 5-63 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.16 Diagnostics of the Analog Modules Programmable and Non-Programmable Diagnostic Messages In diagnostics, we make a distinction between programmable andnon-programmable diagnostic messages. You obtain ...

Analog Modules 5-64 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Diagnostic Messages of the Analog Input Modules The table below gives an overview of the diagnostic messages for the analog inputmodules with diagnostics capability. You can find out which diagnostic mes...

Analog Modules 5-65 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Note A prerequisite for detecting the errors indicated by programmable diagnosticmessages is that you must have assigned parameters to the analog moduleaccordingly in STEP 7. Causes of Errors and Remedial...

Analog Modules 5-67 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.17 Analog Module Interrupts Introduction In this Section, the interrupt behavior of the analog modules is described. Thefollowing interrupts exist: • Diagnostic Interrupt • Hardware interrupt Note that ...

Analog Modules 5-68 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Hardware Interrupt with Trigger “Upper or Lower Limit Exceeded” Define a working range by setting parameters for an upper and lower limit value. Ifthe process signal (for example, the temperature) leaves...

Analog Modules 5-69 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Hardware Interrupt on Trigger “Reached End of Scan Cycle” By parameterizing the hardware interrupt a the end of the scan cycle, you have theoption of synchronizing a process with the scan cycle of the ana...

Analog Modules 5-70 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.18 Analog Input Module SM 431; AI 8 13 Bit; (6ES7431-1KF00-0AB0) Characteristics The analog input module SM 431; AI 8 13 Bit has the following features: • 8 inputs for voltage/current measurement • 4 i...

Analog Modules 5-71 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Block Diagram of the SM 431; AI 8 13 Bit A D +5V 0V CH1 CH7 CH0 +5V –5V 0V Suppressor circuit, current jumpering MV0+ MI0+ MI0+ M0– CH1 CH7 F_CON Bus control M Bus S7-400 ANA Frontconnectormonitoring Bus ...

Analog Modules 5-72 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Terminal Assignment Diagram of the SM 431; AI 8 13 Bit MANA V A V A Voltage measurement Current measure-ment Resistance mea-surement MV0+ MV0+ M0+ M0– M1+ M1– M2+ M2– M3+ M3– M0– MV1+ M1– MV2+ M2– MV3+ M...

Analog Modules 5-73 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Technical Specifications of the SM 431; AI 8 13 Bit Programming package Associated programmingpackage As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx. 5...

Analog Modules 5-74 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Status, Interrupts, Diagnostics Interrupts None Diagnostic functions None Substitute value can be applied No Data for Selecting a Sensor Input range (rated values)/inputresistance • Voltage " 1 V/200...

Analog Modules 5-75 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.18.2 Measuring Methods and Measuring Ranges of theSM 431; AI 8 13 Bit Measuring Methods You can set the following measuring methods for the input channels: • Voltage measurement • Current measurement • ...

Analog Modules 5-76 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Measuring Ranges You set the measuring ranges by means of the “Measuring Range” parameter inSTEP 7. Table 5-50 Measuring Ranges of the SM 431; AI 8 x 13 Bit Method Selected Measuring Range Description U:...

Analog Modules 5-78 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Terminal Assignment Diagram of the SM 431; AI 8 14 Bit ThermocouplesVoltage measurementCurrent measurement Resistance measurementResistance thermometer M1+ M2– M3– M4– M5– M6– M7– CH0 CH1 CH2 CH3 CH4 CH5...

Analog Modules 5-83 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.19.1 Commissioning the SM 431; AI 8 14 Bit You set the mode of operation of the SM 431; AI 8 14 Bit by means of measuring range modules on the module and in STEP 7. Measuring Range Module A measuring ra...

Analog Modules 5-84 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Table 5-51 Parameters of the SM 431; AI 8 14 Bit, continued Parameter Scope Parameter Type Default 1 Value Range • Interferencesuppression 60 Hz; 50 Hz 50 Hz Static Channel • Smoothing NoneLowAverageHigh...

Analog Modules 5-85 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.19.2 Measuring Methods and Measuring Ranges of theSM 431; AI 8 14 Bit Measuring Methods You can set the following measuring methods for the input channels: • Voltage measurement • Current measurement • ...

Analog Modules 5-86 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Wiring for Resistance and Temperature Measurement The following conditions apply when measuring the resistance and temperaturewith the SM 431; AI 8 x 14 Bit: Table 5-53 Channels for Resistance and Temper...

Analog Modules 5-88 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Table 5-55 Measuring Ranges of the SM 431; AI 8 x 14 Bit, continued Method Selected Description Measuring Range Module Setting Measuring Range (Type of Sensor) TC-L: Thermocouple(linear)(temperaturemeasu...

Analog Modules 5-89 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Wire Break Check for Temperature or Resistance Measurement The wire break check is intended primarily for temperature measurements (TC,RTD) or resistance measurements. Always parameterize the wire break c...

Analog Modules 5-90 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.20 Analog Input Module SM 431; AI 8 14 Bit; (6ES7431-1KF20-0AB0) Characteristics The analog input module SM 431; AI 8 14 Bit has the following features: • Rapid A/D changeover, therefore particularly s...

Analog Modules 5-91 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Terminal Assignment Diagram of the SM 431; AI 8 14 Bit Voltage measurementCurrent measurement Resistance measurement M1+ M2– M3– M4– M5– M6– M7– CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 L+ V A A M Tr Tr L+ M0+M0– ...

Analog Modules 5-94 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.20.1 Commissioning the SM 431; AI 8 14 Bit You set the mode of operation of the SM 431; AI 8 14 Bit by means of measuring range modules on the module and in STEP 7. Measuring Range Modules A measuring ...

Analog Modules 5-95 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Smoothing of the Measured Values You will find information that is generally applicable to the smoothing of analogvalues in Section 5.6. You can only set strong smoothing for the SM 431; AI 8 14 Bit. The ...

Analog Modules 5-96 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Step Response with Strong Smoothing The following figure illustrates the contents of Table 5-57. It shows the filter settlingtime after which, in the case of a step response, the smoothed analog value is...

Analog Modules 5-97 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Circuit Variants of the Channels Two channels are set in each case with the measuring range module. There aretherefore restrictions as regards the measuring method for the adjacent channels0/1, 2/3, 4/5 a...

Analog Modules 5-98 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Unused Channels Unused channels can usually be left open. Put the measuring range modules inposition “B”. You can improve the noise immunity of the module in a measuringenvironment with serious interfere...

Analog Modules 5-99 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.21 Analog Input Module SM 431; AI 16 13 Bit; (6ES7431-0HH00-0AB0) Characteristics The analog input module SM 431; AI 13 16 Bit has the following features: • 16 inputs for voltage/current measurement • U...

Analog Modules 5-101 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Terminal Assignment Diagram of the SM 431; AI 16 x 13 Bit Voltage measurementCurrent measurement M1+ M2– M3– M4– M5– M6– M7– CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 L+ M0+M0– M1– M2+ M3+ M4+ M5+ M6+ M7+ M M8– M9...

Analog Modules 5-104 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 5.21.1 Commissioning the SM 431; AI 16 13 Bit You set the mode of operation of the SM 431; AI 16 13 Bit by means of measuring range modules on the module and in STEP 7. Measurement Range Modules A measu...

Analog Modules 5-106 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Unused Channels Unused channels can usually be left open. Put the measuring range modules inposition “B”. You can improve the noise immunity of the module in a measuringenvironment with serious interfer...

Analog Modules 5-108 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Block Diagram of the SM 431; AI 16 16 Bit Bus S7-400 Bus control A D CH0 CH1 + 15 V + 5 V 0 V –15 V + 5 V 0 V I const Diagnostics in L+ loop L + M PGA Multiplexer Opto relay CH14 CH15 Meas. range Meas. ...

Analog Modules 5-109 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Terminal Assignment Diagram of the SM 431; AI 16 16 Bit ThermocouplesVoltage measurementCurrent measurement Resistance measurementResistance thermometer M1+ M2– M3– M4– M5– M6– M7– CH0 CH1 CH2 CH3 CH4 CH...

Analog Modules 5-110 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Technical Specifications of the SM 431; AI 16 16 Bit Programming package Associated programmingpackage As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx...

Analog Modules 5-116 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Smoothing of the Measured Values You fill find information that is generally applicable to the smoothing of analogvalues in Section 5.6. The following figure indicates for the module the number of modul...

Analog Modules 5-118 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Example If you have select “current (two-wire transmitter)” for channel 6, you can onlydisable the measuring method or set “current (two-wire transmitter)” for channel 7. Circuit for Resistance and Temp...

Analog Modules 5-121 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Wire Break Check The wire break check is intended primarily for temperature measurements (TC,RTD) or resistance measurements. Always parameterize the wire break check inthese cases as this ensures that i...

Analog Modules 5-123 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Block Diagram of the SM 431; AI 8 RTD 16 Bit Backplane bus interface BusS7-400 SO+0SE+0SE–0AGND SO+7SE+7SE–7AGND CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 A/D converter Isolation Internal voltage supply Figure 5-3...

Analog Modules 5-124 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Terminal Assignment Diagram of the SM 431; AI 8 RTD 16 Bit SO0 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 SE+0SE–0 AGND 293031323334353637 39404142434445464748 38 123456789 10111213141516171819202122232425262728 I...

Analog Modules 5-128 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Displaying Parameter Assignment Errors The SM 431; AI 8 RTD 16 Bit is capable of diagnostics. Below you will find an overview of the displays that are possible for modules with parameter assignmenterror...

Analog Modules 5-129 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.23.2 Measuring Methods and Measuring Ranges of the SM 431;AI 8 RTD 16 Bit Measuring Methods As the measuring method for the input channels, you can set the temperaturemeasurement. Unused Channels Disab...

Analog Modules 5-131 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Block Diagram of the SM 431; AI 8 16 Bit Backplane bus interface BusS7-400 M0+ M0+R0 M0– CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH0 A/D converter Internal supply Figure 5-41 Block Diagram of the SM 431; AI 8 x 16 B...

Analog Modules 5-132 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Terminal Assignment Diagram of the SM 431; AI 8 16 Bit R0 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 M0+M0+ M0– INTFEXTF Word 0 Word 2 Word 4 Word 6 Word 1 Word 3 Word 5 Word 7 V A V A Tr Tr R1 M1+M1+ M1– R2 M2+M2...

Analog Modules 5-133 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Technical Specifications of the SM 431; AI 8 16 Bit Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx. 650 g Data for Specific Module Number of inputs 8 Length of cable • S...

Analog Modules 5-136 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Table 5-74 Parameters of the SM 431; AI 8 16 Bit, continued Parameter Scope Parameter Type Default 2) Value Range • Smoothing NoneLowAverageHigh None • Reference junction (reference to the coldjunction)...

Analog Modules 5-137 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Step Response at an Interference Frequency Suppression of 10 Hz 100 0 Smoo-thing:None:Low:Average:High: Response time in ms Signal variationin percent Step response for any analog input signal 100 200 16...

Analog Modules 5-138 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Step Response at an Interference Frequency Suppression of 60 Hz 100 0 Smoo-thing:None:Low:Average:High: Response time in ms Signal variationin percent Step response for any analog input signal 160 80 24...

Analog Modules 5-141 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.25 Analog Output Module SM 432; AO 8 13 Bit; (6ES7432-1HF00-0AB0) Characteristics The SM 432; AO 8 x 13 Bit has the following features: • 8 outputs • The individual output channels can be programmed as...

Analog Modules 5-142 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Terminal Assignment Diagram of the SM 432; AO 8 x 13 Bit Voltage output Current output S0– CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 L+ M L+ QV0S0+ M QI0 QI1 QI2 QI3 CH0 CH2 CH3 QI4 QI5 QI6 QI7 CH4 CH5 CH6 CH7 L+...

Analog Modules 5-143 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Technical Specifications of the SM 432; AO 8 x 13 Bit Programming package Associated programmingpackage As of STEP 7 V 2.0 Dimensions and Weight Dimensions W H D (in millimeters) 25 290 210 Weight Approx...

Analog Modules 5-145 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 5.25.1 Commissioning the SM 432; AO 8 13 Bit Parameter You will find a description of the general procedure for assigning parameters toanalog modules in Section 5.7. You will find an overview of the prog...

6-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Interface Modules Chapter Overview Section Description Page 6.1 Common Features of the Interface Modules 6-2 6.2 The Interface Modules IM 460-0; (6ES7460-0AA00-0AB0, 6ES7460-0AA01-0AB0) and IM 461-0; (6ES7461-0AA00-0AA0,...

Interface Modules 6-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 6.1 Common Features of the Interface Modules Function Interface modules (a send IM and a receive IM) are required if one or moreexpansion units (EU) are to be connected to a central controller (CC). Th...

Interface Modules 6-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Connection possibilities for central racks and expansion racks Central rack CR Expansion rack ER 1 Expansion rack ER 4 Expansion rack ER 1 Expansion rack ER 1 Expansion rack ER 4 Expansion without 5 V l...

Interface Modules 6-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Rules for Connection When you connect a central rack to expansion racks, you must observe thefollowing rules: • You can connect up to 21 ERs of the S7-400 to one CR. • The ERs are assigned numbers to i...

Interface Modules 6-5 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 The following figure shows you a typical configuration with send IMs, receive IMsand terminators. CC Send IM Receive IM Receive IM Terminator Figure 6-1 Example: Configuration with Send IMs, Receive IMs...

Interface Modules 6-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Installation and Removal of the Modules During Operation Please read the following warning on the insertion and removal of the interfacemodules and associated connecting cables. ! Caution Data may be l...

Interface Modules 6-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 6.2 The Interface Modules IM 460-0; (6ES7460-0AA00-0AB0, 6ES7460-0AA01-0AB0) and IM 461-0; (6ES7461-0AA00-0AA0, 6ES7461-0AA01-0AA0) Position of the Operator Controls and Indicators of the IM 460-0 and I...

Interface Modules 6-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Function The interface module pair IM 460-0 (send IM) and IM 461-0 (receive IM) are usedfor a local link. The communication bus is transferred at the full transmission rate. Parameter Assignment for th...

Interface Modules 6-9 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Operator Controls and Indicators of the Receive IM INTF LED (red) Lights up if a rack number > 21 or = 0 was set. Lights up if you have changed the rack number under voltage. EXTF LED (red) Lights up...

Interface Modules 6-11 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Function The interface module pair IM 460-1 (send IM) and IM 461-1 (receive IM) are usedfor a local link (up to a maximum 1.5 m in total). A 5 V supply voltage is alsotransferred with these interface m...

Interface Modules 6-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Operator Controls and Indicators on the Send IM EXTF LED(red) Lights up in the event of an external fault Line 1 or line 2 is faulty(terminator missing or open circuit) C1 LED(green) Line 1 (via front...

Interface Modules 6-13 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Technical Specifications of the IM 460-1 and IM 461-1 Maximum line length (total) 1.5 m Dimensions W x H x D (mm) 25 x 290 x 280 Weight • IM 460-1 • IM 461-1 600 g 610 g Current consumption from the S7...

Interface Modules 6-15 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Function The interface module pair IM 460-3 (send IM) and IM 461-3 (receive IM) are usedfor a remote link of up to a maximum 102 m (exactly: 100 m plus inputs/outputs of0.75 m in the line). The communi...

Interface Modules 6-17 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Technical Specifications of the IM 460-3 and IM 461-3 Maximum line length (total) 102 m Dimensions W x H x D (mm) 25 x 290 x 280 Weight • IM 460-3 • IM 461-3 630 g 620 g Current consumption from the S7...

Interface Modules 6-19 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Function The interface module pair IM 460-4 (send IM) and IM 461-4 (receive IM) are usedfor a remote link of up to a maximum 605 m (exactly: 600 m plus inputs/outputs of1.5 m in the line). Parameteriza...

Interface Modules 6-21 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Technical Specifications of the IM 460-4 and IM 461-4 Maximum line length (total) 605 m Dimensions W x H x D (mm) 25 x 290 x 280 Weight • IM 460-4 • IM 461-4 630 g 620 g Current consumption from the S7...

7-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 IM 463-2 Chapter Overview Section Description Page 7.1 Using SIMATIC S5 Expansion Units in an S7-400 7-2 7.2 Rules for Connecting S5 Expansion Units 7-3 7.3 Operator Controls and Indicators 7-4 7.4 Installing and Connect...

IM 463-2 7-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 7.1 Using SIMATIC S5 Expansion Units in an S7-400 Area of Application The IM 463-2 interface module is used for distributed connection of S5 expansionunits to an S7-400. You can use the IM 463-2 in the CR of th...

IM 463-2 7-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 7.2 Rules for Connecting S5 Expansion Units Introduction When you connect S5 expansion units to an S7-400 via the IM 463-2, there arerules to observe with regard to cable length, maximum expansion, use of atermi...

IM 463-2 7-5 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 LEDs Table 7-2 LEDs of the IM 4632 LED Meaning LED EXTF (red) Lights up in the event of an external fault. Chain 1 or chain 2 has afault (power supply failed in the EU; terminating connector missing;wire break, ...

IM 463-2 7-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 7.4 Installing and Connecting the IM 463-2 Introduction To install an IM 463-2 in a CR of the S7-400, proceed in the same way as wheninstalling other S7-400 modules (see Installation Manual, Chapter 5). To conn...

IM 463-2 7-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Plugging in the Connecting Cable To plug in the connecting cable, follow the steps outlined below: 1. Open the cover of the IM 463-2. 2. Plug the new connector of the connecting cable into one of the connectors ...

IM 463-2 7-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 7.5 Setting the Operating Modes of the IM 314 Introduction To operate the IM 463-2, you must set on the IM 314 the S5 expansion unit usedand the address area of the S5 I/O modules. Setting the S5 Expansion Unit...

IM 463-2 7-9 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Setting the Address Area The address area of the S5 I/O modules is set on the IM 314. This setting appliesonly for the digital and analog I/O modules. The address areas P, Q, IM3, and IM4 are available. Set the ...

IM 463-2 7-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 7.6 Configuring S5 Modules for Operation in the S7-400 You configure the S5 modules using STEP 7. See the description of STEP 7 or theonline help function for details of how to proceed. The following figure sh...

IM 463-2 7-11 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 7.7 Pin Assignments of the 721 Connecting Cable Table 7-6 Assignment of the Connecting Cable 721 ÍÍÍÍÍÍÍÍÍÍÍ ÍÍÍÍÍÍÍÍÍÍÍ ÍÍÍÍÍÍÍÍÍÍÍ 34 50 17 1 ÍÍÍÍÍÍÍÍÍÍÍ ÍÍÍÍÍÍÍÍÍÍÍ ÍÍÍÍÍÍÍÍÍÍÍ 34 50 17 1 Connector 50-Pin Co...

IM 463-2 7-13 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 7.8 Terminating Connector for IM 314 Introduction The IM 314 of the last expansion unit of each chain is terminated with the6ES5 760-1AA11 terminating connector. Table 7-7 Assignment of the Terminator 760-1AA11...

8-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 PROFIBUS DP Master InterfaceIM 467/IM 467 FO Chapter Overview Section Description Page 8.1 PROFIBUS DP Master Interface IM 467/IM 467 FO 8-2 8.2 Configuration 8-6 8.3 Connection to PROFIBUS DP 8-8 8.4 Technical Specifica...

PROFIBUS DP Master Interface IM 467/IM 467 FO 8-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 8.1 PROFIBUS DP Master Interface IM 467/IM 467 FO Order Numbers IM 467 6ES7467-5GJ02-0AB0 (RS 485) IM 467 FO 6ES7467-5FJ00-0AB0 (F0) Application PROFIBUS DP, standardized to...

PROFIBUS DP Master Interface IM 467/IM 467 FO 8-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 PROFIBUS DP interface9-pin subminiature D LEDs Mode selector Figure 8-1 Configuration of the IM 467/467 FO Communication Services The IM 467/IM 467 FO offers two communicatio...

PROFIBUS DP Master Interface IM 467/IM 467 FO 8-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 8.1.1 Indicators and the Mode Selector LED The LED plate on the front panel of the IM 467/IM 467 FO has the following four indicators: INTF EXTF RUNSTOP Figure 8-2 LEDs of t...

PROFIBUS DP Master Interface IM 467/IM 467 FO 8-5 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Controlling the Operating Mode There are two ways to control the operating mode of the IM 467/IM 467 FO: • By using the mode selector • By using the programming device/PC Mod...

PROFIBUS DP Master Interface IM 467/IM 467 FO 8-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 8.2 Configuration The IM 467/IM 467 FO is configured with STEP 7. The configuration data areretained even in the event of a power failure; a memory module is not required.Us...

PROFIBUS DP Master Interface IM 467/IM 467 FO 8-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Prerequisites The IM 467/IM 467 FO is supported by all the CPU operating systems beginningwith the release numbers listed below. You will also find the following information ...

PROFIBUS DP Master Interface IM 467/IM 467 FO 8-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 8.3 Connection to PROFIBUS DP There are two ways of connecting to PROFIBUS DP: • Electrical connection via a bus connector • Optical connection using a fiber-optic cable 8.3...

PROFIBUS DP Master Interface IM 467/IM 467 FO 8-9 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Connector Pin Assignment The electrical interface used to connect to PROFIBUS DP (9-pin subminiature D female connector) is specified in thefollowing table. 123456789 PE–RxD/...

PROFIBUS DP Master Interface IM 467/IM 467 FO 8-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 8.3.3 Connecting a Fiber-Optic Cable to the IM 467 FO Accessories Required • Pack of Simplex connectors and polishing sets (6GK1901-0FB00-0AA0) • Pack of plug-in adapters (...

PROFIBUS DP Master Interface IM 467/IM 467 FO 8-11 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Reusing Fiber-Optic Cables NoteIf you insert used fiber-optic cables in the plug-in adapter again, you must cut offthe bent lengths of both fiber-optic cable cores and insta...

PROFIBUS DP Master Interface IM 467/IM 467 FO 8-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 8.4 Technical Specifications 8.4.1 Technical Specifications of the IM 467 6ES7467-5GJ02-0AB0. Dimensions and Weight Dimensions W x H x D (mm) Weight 25 x 290 x 210 700 g PR...

PROFIBUS DP Master Interface IM 467/IM 467 FO 8-13 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 8.4.2 Technical Specifications of the IM 467 FO 6ES7 467-5FJ00-0AB0 Dimensions and Weight Dimensions W x H x D (mm) Weight 25 x 290 x 210 700 g PROFIBUS DP • Standard • Tran...

9-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Cable Duct and Fan Subassemblies Chapter Overview Section Description Page 9.1 Fan Monitoring in the Fan Subassemblies 9-2 9.2 Cable Duct; (6ES7408-0TA00-0AA0) 9-4 9.3 The 120/230 VAC Fan Subassembly; (6ES7408-1TB00-0XA0...

Cable Duct and Fan Subassemblies 9-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 9.1 Fan Monitoring in the Fan Subassemblies In this section, you will find out how to monitor the fans. There is a signaling concept example at the end of the section. LEDs The three red...

Cable Duct and Fan Subassemblies 9-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Signaling Concept Example You can check the fault-free functioning of the fan subassembly using digital inputs. You can cause the power supply to be cut off after the failure of at least ...

Cable Duct and Fan Subassemblies 9-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 9.2 Cable Duct; (6ES7408-0TA00-0AA0) Function The cable duct is used in installations outside the cabinet for • Cable clamping and/or for • Shielding or for • Air circulation without fan...

Cable Duct and Fan Subassemblies 9-5 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 9.3 The 120/230 VAC Fan Subassembly; (6ES7408-1TB00-0XA0) Operator Controls and Indicators on the 120/230 VAC Fan Subassembly LEDs F1, F2, F3 Quick-release lock Relay contacts 1, 2, 3 Rel...

Cable Duct and Fan Subassemblies 9-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Shielding Clamps If you do not require the shielding clamps supplied, do not install them in the fansubassembly. Technical Specifications Dimensions, Weights Dimensions WxHxD (mm) 482.5 ...

Cable Duct and Fan Subassemblies 9-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 9.4 The 24 VDC Fan Subassembly; (6ES7408-1TA00-0XA0) Operator Controls and Indicators on the 24 VDC Fan Subassembly LEDs F1, F2, F3 Quick-release lock Relay contacts 1, 2, 3 Relay contact...

Cable Duct and Fan Subassemblies 9-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Signaling Concept The signaling concept of the 24 VDC fan subassembly is identical to the signalingconcept of the 120/230 VAC fan subassembly. Fuse Included in this fan subassembly are s...

10-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 RS 485 Repeater In this Chapter In this chapter, you will find a detailed description of the RS 485 repeater. Included in the description are: • The purpose of the RS 485 repeater • The maximum cable lengths possible be...

RS 485 Repeater 10-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 10.1 Application and Characteristics (6ES7972-0AA01-0XA0) What is an RS 485 Repeater? The RS 485 repeater amplifies data signals on bus lines and interconnects bussegments. Application of the RS 485 Rep...

RS 485 Repeater 10-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 10.2 Appearance of the RS 485 Repeater; (6ES7972-0AA01-0XA0) The table below shows the appearance of the RS 485 repeater and lists itsfunctions. Table 10-3 Description and Functions of the RS 485 Repeate...

RS 485 Repeater 10-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 10.3 RS 485 Repeater in Ungrounded and Grounded Operation Grounded or Ungrounded The RS 485 repeater is ... • grounded, if all other nodes in the segment are also operated with a groundedpotential • ung...

RS 485 Repeater 10-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Amplification of the Bus Signals The amplification of the bus signals takes place between the port for bus segment1 or the PG/OP interface and the port for bus segment 2. 10.4 Technical Specifications T...

RS 485 Repeater 10-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Block Diagram of the RS 485 Repeater • Bus segment 1 and bus segment 2 are galvanically isolated from each other. • Bus segment 2 and the PG/OP socket are galvanically isolated from each other. • Signals...

11-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 CPUs for M7-400 In this Chapter This chapter describes the CPUs of the M7-400 automation computer: • CPU 486-3, • CPU 488-3, The CPUs differ essentially in their clock frequencies. You will find a comparison oftheir per...

CPUs for M7-400 11-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 11.3 Function Elements Introduction In this section you will become familiar with the individual function elements of theCPU 486-3 and CPU 488-3. You require the information here to be able to respondto...

CPUs for M7-400 11-5 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 CPU Elements The following table gives the meanings of the individual elements of the CPU 486-3and CPU 488-3. Table 11-3 Elements of the CPU 486-3 and CPU 488-3 Element Meaning Status and fault LEDs The ...

CPUs for M7-400 11-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 11.3.1 Status and Fault LEDs Status and Fault LEDs The CPU 486-3 and CPU 488-3 have the following status and fault LEDs: INTF EXTF SD HD USR1 USR2 RUN STOP Figure 11-2 Status and Fault LEDs on the CPU 4...

CPUs for M7-400 11-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Meaning of the Status and Fault LEDs The status and fault LEDs are explained in Table 11-4 in the order in which they arearranged on the CPU 486-3 and CPU 488-3 modules. The following status andfault LED...

CPUs for M7-400 11-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 11.3.2 Memory Cards Introduction The CPU 486-3 and CPU 488-3 offer the possibility of operating a memory card inthe same way as a diskette. In this section, you will learn how you can use theseoptions. ...

CPUs for M7-400 11-9 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 11.3.3 Mode Selector Switch Mode Selector Switch The mode selector switch of the CPUs is a keyswitch. You can see the positions of the mode selector switch in the following figure. MRES STOP RUN RUN-P Fi...

CPUs for M7-400 11-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Table 11-5 Positions of the Mode Selector Switch Position of the Mode Selector Switch Explanations STOP I/O access is disabled for the user program of the CPU. The userprogram cannot control the proces...

CPUs for M7-400 11-11 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 11.3.4 Submodule Receptacles for Interface Submodules Submodule Receptacle Definition The submodule receptacle is a slot for a submodule. The CPU 486-3 andCPU 488-3 have a receptacle for the memory card...

CPUs for M7-400 11-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Numbering on the Submodule Receptacles Each receptacle for an interface submodule has a submodule receptacle numberassigned to it. The submodule receptacle number depends on the module slot andon the a...

CPUs for M7-400 11-13 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 11.3.5 Memory Submodules Suitable for the Main Memory Introduction You must order the MEM 478 DRAM memory submodules for the main memory ofthe CPUs separately. They are also shipped separately. These me...

CPUs for M7-400 11-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 11.3.6 Expansion Socket Introduction The CPU 486-3 and CPU 488-3 are each equipped with an expansion socket. TheISA bus is continued via the expansion socket. Which Expansions Can Be Connected? One EXM...

CPUs for M7-400 11-15 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 11.3.7 Multipoint Interface (MPI) X1 Interface The X1 interface of the CPU 486-3 and CPU 488-3 for connecting devices such asPCs/programming devices is a multipoint interface (MPI) and is connected via ...

CPUs for M7-400 11-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 11.4 The BIOS Setup Overview The BIOS setup handles the configuration of the relevant CPUs in your M7-400system. The settings and technical information concerning the configuration of thisprogrammable ...

CPUs for M7-400 11-17 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 11.4.1 BIOS Power Up Power Up without Error Message After switching on or after warm restart of the CPU, the BIOS (Basic Input OutputSystem) starts a ”Power On Self Test” (POST) and displays the results...

CPUs for M7-400 11-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Power Up with Error Message If one of the following errors occurs: • Memory test error • Hard disk configuration error • CMOS checksum error, the INTF LED remains lit as well as the STOP LED. A window ...

CPUs for M7-400 11-19 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 11.4.2 BIOS Hot Keys BIOS Hot Keys After power up, the BIOS offers the user a range of functions under MS-DOS.These functions are executed by pressing the following groups of keyssimultaneously: Table 1...

CPUs for M7-400 11-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 11.4.3 Operator Inputs in the BIOS Setup Definition of the Setup Fields Within the BIOS setup, there are fields in which you can make entries or selections.These fields have the following functions: • ...

CPUs for M7-400 11-21 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Key Control within the Setup Menu The following keys are used for control within the Setup menu and the associatedsetup page (conforming to the Windows TM Standard): ENTER With this key, you jump to the...

CPUs for M7-400 11-22 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 ↑ ↓ With the cursor control keys, you can jump from line to line within alist box. The line you are in is marked with a dark bar. You can page with the cursor control keys within an edit box if there a...

CPUs for M7-400 11-23 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 11.4.4 Opening and Exiting the BIOS Setup Opening the Setup Menu To open the Setup menu, press the following keys simultaneously while the CPU is powering up and the POST window (Figure 11-6) is on the ...

CPUs for M7-400 11-24 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Exiting the BIOS Setup To exit the BIOS setup, activate the EXIT button shown in Figure 11-9 or press ESC . The “Setup Exit” dialog box then appears (see Figure 11-10). Figure 11-10 “Setup Exit” Dialog...

CPUs for M7-400 11-25 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 What is the Purpose of the Setup Page? This setup page contains notes that help you to use the Setup menu. OK Button Activating this button returns to the Setup menu. 11.4.6 Setup Page “IF modules” Open...

CPUs for M7-400 11-26 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Accepting Edited Values Only the values for which the relevant interface submodule has been designed areaccepted by the system in the edit boxes. If, for example, you enter three valuesunder “Interrupt...

CPUs for M7-400 11-27 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Interrupt Source Here, you set interrupts A to C (see the “Interface Submodules” chapter) providedfor the interface submodule. The values positioned on the left are setpoints. Youcan edit these. The val...

CPUs for M7-400 11-28 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Value (Gray Type) Under the address set with “Config. Index”, you can now enter the configurationvalue. You will find this value and its significance in the chapter “InterfaceSubmodules” under the rele...

CPUs for M7-400 11-29 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 11.4.7 Setup Page “Timeout Function” Opening the Setup Page If you have selected “Timeout Function” in the Setup menu (Figure 11-9 onpage 11-23) and activated the OPEN button, this setup page appears on...

CPUs for M7-400 11-30 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 CANCEL Button Activating this button returns to the Setup menu. Deletes all changes you havemade on the setup page. 11.4.8 Setup Page “Security” Opening the Setup Page If you have selected “Security” i...

CPUs for M7-400 11-31 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Password Enter SetupBy activating this check box, you can assign a password that authorizes access tothe Setup. System BootBy activating this check box, you can assign a password that permits booting of...

CPUs for M7-400 11-32 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 11.4.9 Setup Page “Date and Time” Opening the Setup Page If you have selected “Date and Time” and activated the OPEN button in the Setupmenu (Figure 11-9 on page 11-23), this BIOS setup page appears on...

CPUs for M7-400 11-33 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 11.4.10 “Hard Disk” Setup Page Opening the Setup Page If you have selected “Hard Disk” and activated the OPEN button in the Setup menu(Figure 11-9 on page 11-23), this BIOS setup page appears on the scr...

CPUs for M7-400 11-34 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Translation Mode In Translation Mode you have four possible settings: • Autoreads the hard disk parameters and automatically sets the correct mode(Normal, LBA, Large). The Translation Mode “Auto” is se...

CPUs for M7-400 11-35 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 11.4.11 Setup Page “Floppy/Card” Opening the Setup Page If you have selected “Floppy/Card” and activated the OPEN button in the Setupmenu (Figure 11-9 on page 11-23), this setup page appears on the scre...

CPUs for M7-400 11-36 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 11.4.12 Setup Page “Boot Options” Opening the Setup Page If you have selected “Boot Options” and activated the OPEN button in the Setupmenu (Figure 11-9 on page 11-23), this setup page appears on the s...

CPUs for M7-400 11-38 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 11.4.13 Setup Page “System” Opening the Setup Page If you have selected “System” and activated the OPEN button in the Setup menu(Figure 11-9 on page 11-23), this setup page appears on the screen(Figure...

CPUs for M7-400 11-39 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 System Cache For the memory areas of the System ROM, the VIDEO ROM, and the addresses ofBIOS expansions, you can set whether they are copied to the Shadow RAM andwhether the cache should be used. • Syst...

CPUs for M7-400 11-40 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 11.5 I/O Addresses, Main Memory and Interrupt Assignments Introduction This section gives you detailed information, in the form of a table, on the I/Oaddress space assignment, main memory and interrupt...

CPUs for M7-400 11-41 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Memory Areas for AT Cards AT cards which are inserted in the expansion module ATM 478 can occupy thefollowing memory areas: Range M7 RMOS32 M7 RMOS32 with MS-DOS M7 RMOS32 with Without EMS With EMS with...

CPUs for M7-400 11-42 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Interrupt Assignment Table 11-9 Interrupt Assignment Interrupt Function NMI Group interrupt for faults and reset signals IRQ0 System timer IRQ1 Reserved for keyboard IRQ2 Cascading of the 2nd interrupt...

M7-400 Expansions 12-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.1 Overview Introduction You can expand your automation computer from the M7-400 range by addingexpansion modules for interface submodules, short AT modules, and/or the massstorage module. The inter...

M7-400 Expansions 12-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 e.g. FM 456-4 e.g. EXM 478 e.g. ATM 478 e.g. MSM 478 Figure 12-2 Maximum Expansion with Expansion Modules

M7-400 Expansions 12-5 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Permissible Combinations You can see from the table below which expansions can be connected to theprogrammable M7-400 modules. Table 12-1 Expansion Possibilities of the CPU 486-3, CPU 488-3, or FM 456 ...

M7-400 Expansions 12-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.2 EXM 478 Expansion Module; (6ES7 478-2AC00-0AC0) Characteristics The EXM 478 expansion module is used to house up to three interfacesubmodules. By installing the relevant interface submodule in th...

M7-400 Expansions 12-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 12.2.1 Addressing the EXM 478 Expansion Module Introduction In order to be able to program the interface submodules in the EXM 478 expansionmodule, you must be able to determine their addresses. There ...

M7-400 Expansions 12-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Numbering of the Submodule Receptacles Each receptacle (slot) for an interface submodule has a submodule receptaclenumber assigned to it. The submodule receptacle number depends on theconfiguration of...

M7-400 Expansions 12-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Division of Addresses in the M7-400-Specific I/O Address Area The EXM 478 expansion module is operated on the ISA bus of the programmablemodule. The I/O address area from C000 H (to D2FF H ) in the C...

M7-400 Expansions 12-11 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Addresses Within an Expansion Module Each expansion module occupies 256 bytes (100 H ) within the CPU/FM address area. The division of the 256 addresses within an expansion module can be seenfrom Tabl...

M7-400 Expansions 12-13 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 12.2.2 Interrupt Assignments, Signal Switching EXM 478 Introduction Up to three interrupts per interface submodule are permitted in an EXM 478expansion module. The various possible methods of interrup...

M7-400 Expansions 12-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.2.3 Technical Specifications of the EXM 478 Expansion Module Technical Specifications of the EXM 478 The table below contains the technical specifications of the EXM 478 expansionmodule: EXM 478 6...

M7-400 Expansions 12-15 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 12.3 ATM 478 AT Adapter Module; (6ES7 478-2CA00-0AC0) Characteristics The ATM 478 AT adapter module is used to accommodate a short AT module(card). The ATM 478 AT adapter module has a 120-pin connecto...

M7-400 Expansions 12-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.3.1 Pin Assignments of the AT Module Pin Assignments The ATM 478 AT adapter module has a 98-pin standard direct connector for shortAT modules (see Figure 12-8). 16 bit data 8 bit data Figure 12-8 ...

M7-400 Expansions 12-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Table 12-5 Pin Assignments of the 98-Pin Standard Direct Connector (ATConnector), continued Pin Signal Name Pin Signal Name AT Expansion D1 MEMCS_16_N C1 SBHE_N D2 I/OCS16_N C2 LA23 D3 IRQ10 C3 LA22 ...

M7-400 Expansions 12-19 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 12.3.2 Technical Specifications of the ATM 478 AT Adapter Module Technical Specifications of the ATM 478 The table below contains the technical specifications of the ATM 478 AT adaptermodule: ATM 478 ...

M7-400 Expansions 12-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Example of Power Loss Calculation The following table contains a calculation example for the total power losses for anAT adapter module with an AT module. Table 12-6 Calculation Example for Total Pow...

M7-400 Expansions 12-21 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Permissible Dimensions of AT Modules The following illustration shows you the maximum and minimum dimensions inmillimeters that AT modules must meet for the ATM 478 AT adapter module. Ifthese dimensio...

M7-400 Expansions 12-22 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 12.4 MSM 478 Mass Storage Module; (6ES7 478-2BA00-0AC0) Characteristics The MSM 478 mass storage module is used for storing programs and largerquantities of data. It also has an AT-compatible paralle...

M7-400 Expansions 12-23 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 12.4.1 LPT1 Parallel Port Characteristics The MSM 478 mass storage module has an AT-compatible parallel port (LPT) forconnecting a printer with Centronics interface. The parallel port can also be used...

M7-400 Expansions 12-25 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 12.4.2 Technical Specifications of the MSM 478 Mass Storage Module Technical Specifications of the MSM 478 The table below contains the technical specifications of the MSM mass storagemodule: 478 With...

13-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Interface Submodules Chapter Overview Section Description Page 13.1 Interface Submodules Overview 13-2 13.2 Submodule IDs and Insertion Rules 13-4 13.3 IF 962-VGA Interface Submodule for M7-300/400;(6ES7962-1BA00-0AC0) ...

Interface Submodules 13-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.1 Interface Submodules Overview Introduction The interface submodules are designed for use in the M7-300 and M7-400automation computers. They can be operated in the M7-400 programmablemodules an...

Interface Submodules 13-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Interrupt Assignments When configuring the interface submodules in the BIOS setup, you can assign ISAinterrupts to the three interrupts of an interface submodule (IRQa, IRQb, IRQc). Forthis purpose,...

Interface Submodules 13-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.2 Submodule IDs and Insertion Rules Submodule IDs The following table contains an overview of the submodule IDs for the interfacesubmodules. Table 13-2 Overview of the Submodule IDs for the Inte...

Interface Submodules 13-5 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13.3 IF 962-VGA Interface Submodule for M7-300/400; (6ES7962-1BA00-0AC0) Characteristics The IF 962-VGA interface submodule is used to connect a keyboard and a VGAscreen. The interfaces to the keybo...

Interface Submodules 13-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.3.1 Pin Assignments Socket X1 VGA Screen Connection Table 13-4 Socket X1, VGA Screen Connection IF 962-VGA (15-Pin High-Density Sub DSocket Connector) Pin Meaning 1 Analog red 2 Analog green 3 A...

Interface Submodules 13-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13.3.2 Addressing, Interrupts, and Submodule ID Addressing Addressing corresponds to the AT standard. The following addresses are occupied by the IF 962-VGA interface submodule:Memory addresses: A00...

Interface Submodules 13-9 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Operating Modes The WD90C24 VGA controller is used on the IF 962-VGA interface submodule.Table 13-7 shows you the video modes supported by the BIOS of the IF 962-VGAinterface submodule. Table 13-7 V...

Interface Submodules 13-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.4 IF 962-COM Interface Submodule for M7-300/400; (6ES7962-3AA00-0AC0) Characteristics The IF 962-COM interface submodule is used to connect devices with a serial port.It contains two serial AT-...

Interface Submodules 13-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.4.2 Addressing and Interrupts Addressing The IF 962-COM interface submodule can be addressed in the following two ways: • In the AT-compatible I/O address area • In the M7-300/400-reserved I/O ...

Interface Submodules 13-13 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Addressing in the M7-300/400-Reserved I/O Address Ares Regardless of possible addresses in the AT-compatible I/O address area, theIF 962-COM interface submodule can be addressed in this reserved ad...

Interface Submodules 13-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Table 13-13 Meaning of the Addressing Type Bits in the Configuration Register(IF 962-COM) I/O Address Addressing Type COM b/a I/O Address Bit 6/2 Bit 5/1 Bit 4/0 Addressing only possible in the re...

Interface Submodules 13-15 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Interrupt Request The interface submodule supplies an interrupt request (IRQa and IRQb) for eachserial port. You can define the assignment of the interrupt requests IRQa and IRQb to theappropriate ...

Interface Submodules 13-16 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.5 IF 962-LPT Interface Submodule for M7-300/400; (6ES7962-4AA00-0AC0) Characteristics The IF 962-LPT interface submodule contains an AT-compatible parallel (LPT) portfor connecting a printer wi...

Interface Submodules 13-17 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13.5.1 Pin Assignments X1 Socket Table 13-15 Socket X1, IF 962-LPT (25-Pin Sub D Socket Connector) Pin Meaning Direction 1 /STROBE Input/output 2 Data 0 Input/output 3 Data 1 Input/output 4 Data 2 ...

Interface Submodules 13-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.5.2 Addressing and Interrupts Addressing The IF 962-LPT interface submodule can be addressed in the following two ways: • In the AT-compatible I/O address area • In the M7-300/400-reserved I/O ...

Interface Submodules 13-19 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Example of Setting an AT-Compatible I/O Address In the following example, the I/O address 0278 H is to be set in the BIOS setup. Proceed as follows to do this: 1. Select the “IF Modules” page in th...

Interface Submodules 13-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Default Settings in the BIOS The following I/O addresses and interrupt numbers are set as defaults in the BIOSfor LPT ports: Port I/O Address Interrupt No. With mass storage module MSM 478 LPT1 (o...

Interface Submodules 13-21 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Table 13-20 Meaning of the Addressing Type Bits in the Configuration Register(IF 962-LPT) I/O Address Addressing Type I/O Address Bit 1 Bit 0 Addressing only possible in the reserved I/O address ar...

Interface Submodules 13-23 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13.6 IF 961-DIO Interface Submodule for M7-300/400; (6ES7961-1AA00-0AC0) Characteristics The IF 961-DIO interface submodule has the following characteristics: • 8 inputs, isolated in groups of 2 In...

Interface Submodules 13-24 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.6.1 Pin Assignments X1 Socket There is a 25-pin sub D socket connector on the frontside of the submodule forplugging in the connecting cable. Figure 13-6 shows the pin assignments of the submod...

Interface Submodules 13-25 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Figures 13-7 and 13-8 show the circuit block diagrams and the terminal connectiondiagrams for wiring the digital inputs and digital outputs. Terminal connection diagram Circuit blockdiagram Interna...

Interface Submodules 13-26 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.6.2 Addressing and Interrupts Addressing in the M7-300/400-Reserved I/O Address Area The base address depends on the interface submodule slot in the expansionmodule or the programmable module. ...

Interface Submodules 13-27 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Digital Output Function Tables 13-24 and 13-25 give an overview of the digital output function. Table 13-24 Offset Address for the Digital Output Function (IF 961-DIO) Offset Address Function Remar...

Interface Submodules 13-28 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Interrupt Register The cause of the interrupt is stored in this register. Tables 13-28 and 13-29 give anoverview of the interrupt register. Table 13-28 Offset Address for the Interrupt Register (I...

Interface Submodules 13-29 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Selection Register Rising Edge Tables 13-32 and 13-33 give an overview of the selection register for interruptgeneration at a rising edge of a digital input. Table 13-32 Offset Address for the Sele...

Interface Submodules 13-30 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Mode Register Tables 13-36 and 13-37 give an overview of the mode register. Table 13-36 Offset Address for the Mode Register (IF 961-DIO) Offset Address Function Remarks 7 Mode register Read/write...

Interface Submodules 13-33 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13.7 IF 961-AIO Interface Submodule for M7-300/400; (6ES7961-2AA00-0AC0) Characteristics The IF 961-AIO interface submodule has the following characteristics: • 4 analog inputs, each as voltage and...

Interface Submodules 13-34 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.1 Pin Assignments and Terminal Connection Diagram X1 Socket There is a 25-pin sub D socket connector on the frontside of the submodule forplugging in the connecting cable. Figure 13-10 shows ...

Interface Submodules 13-35 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Meaning of Signals The following table shows the meanings of the signals in Figure 13-10. Table 13-38 Meaning of the Signals of the X1 Socket of the IF 961-AIO InterfaceSubmodule Signal Meaning MV ...

Interface Submodules 13-36 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Grounding for the Analog Inputs If the valid Common Mode area (V CM ) cannot be retained, the analog inputs must be grounded. To do this, the ground lines of the individual analog inputs (1) and t...

Interface Submodules 13-37 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13.7.2 Connecting Measured Value Sensors to Analog Inputs Introduction Depending on the measuring type, you can connect various measured valuesensors to the analog inputs: • Voltage sensors • Curre...

Interface Submodules 13-38 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Isolated Measured Value Sensors Potential differences can occur between the individual measured value sensors inthe case of isolated measured value sensors. These potential differences canoccur as...

Interface Submodules 13-39 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Non-Isolated Measured Value Sensors Potential differences must not arise between non-isolated measured value sensors.If necessary, you must take additional installation measures (equipotential bond...

Interface Submodules 13-40 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Connection of Current Sensors as Two-Wire and Four-Wire Transducers Figures 13-16 and 13-17 show you how to connect current sensors as two-wireand four-wire transducers to analog input modules. Th...

Interface Submodules 13-42 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.3 Connecting Loads/Actuators to Analog Outputs Abbreviations Used The abbreviations used in Figures 13-20 to 13-21 have the following meanings: QI: Analog output current QV: Analog output vol...

Interface Submodules 13-43 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Connecting Loads to the Voltage Output The following figure shows the wiring of two channels as an example. +24 V R L1 L + QV 1 S 1 Ground bus QV 0 S 0 R L2 M 0 V V CM1 V CM0 Figure 13-21 Connectin...

Interface Submodules 13-44 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.4 Conversion Time and Cycle Time of the Analog Input Channels Introduction This section contains the definitions of and relationships between the conversiontime and the cycle time of analog i...

Interface Submodules 13-45 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13.7.5 Conversion Time, Cycle Time, Settling Time, and ResponseTime of the Analog Output Channels Introduction This section contains the definitions and relationships of times relevant to theanalog...

Interface Submodules 13-46 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.6 Starting Up the IF 961-AIO Interface Submodule Electrical Installation You must connect the ground terminal (M and S 0/ S 1 ) of the analog input/output module with the ground terminal of t...

Interface Submodules 13-47 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13.7.8 Analog Output Function Analog Output Function The 12-bit digital value to be converted is loaded left-justified into the DAC dataregisters of the relevant DAC channel. After the data has bee...

Interface Submodules 13-48 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.9 Analog Input Function Analog Input Function Tables 13-41 ad 13-42 contain an overview of the read and write registers for theanalog input function. The data format of analog input values is...

Interface Submodules 13-49 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Table 13-42 Meaning of the Control Bits in the Analog Input Function (IF 961-AIO) Offset Address D15 Writing D0 Remark 08 H A C I N T 0 0 0 0 0 0 0 0 0 0 0 ta ta ta Control register 1 0A H 0 0 0 0 ...

Interface Submodules 13-50 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Cyclic Conversion of the ADC Channels Below are listed the steps required for cyclic conversion of the ADC channels: 1. Set the AC bit in control register 1 to “1” (offset address “08 H ”). 2. Wai...

Interface Submodules 13-51 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13.7.10 Analog Value Representation for the Measuring Ranges of theAnalog Inputs Voltage and Current Measuring Ranges Table 13-43 contains the representation of the digitized measured value for • T...

Interface Submodules 13-52 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.11 Analog Value Representation for the Measuring Ranges of theAnalog Outputs Voltage and Current Output Ranges Table 13-44 contains the representation of • The voltage output range ± 10 V and...

Interface Submodules 13-53 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13.7.12 Diagnostics, Interrupts, and Submodule ID Interrupt Request The interface submodule supplies an interrupt request (IRQa). You can define the assignment of the IRQa interrupt request to the ...

Interface Submodules 13-54 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.7.13 Technical Specifications Technical Specifications The IF 961-AIO interface submodule receives its supply voltage from the M7-400programmable modules or from the M7-300/400 expansion module...

Interface Submodules 13-56 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.8 IF 961-CT1 Interface Submodule for M7-300/400; (6ES7961-3AA00-0AC0) Characteristics The IF 961-CT1 interface submodule is used for connecting incremental encoders.It has the following charact...

Interface Submodules 13-57 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13.8.1 What Can the IF961-CT1 Interface Submodule Do? Introduction This section contains an overview of the functionality of the IF 961-CT1 interfacesubmodule. This functionality is achieved using ...

Interface Submodules 13-58 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Interrupts The IF 961-CT1 can initiate an interrupt when comparison values are reached or inthe event of overflow, underflow, or zero pass of the counter. Diagnostic Interrupt The IF 961-CT1 can i...

Interface Submodules 13-59 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13.8.2 Addressing and Interrupts Addressing The IF 961-CT1 interface submodule is addressed with the M7-300/400-reservedI/O address area (starting from C000 H ). Addressing in the M7-300/400-Reserv...

Interface Submodules 13-61 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13.9 IF 964-DP Interface Submodule for S7-400 and M7-400 Order Numbers You can use the IF 964-DP interface submodule with order number6ES7964-2AA00-0AB0 (up to 07/99) in the M7-400.You can use the ...

Interface Submodules 13-62 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Additional Front Cover The IF 964-DP interface submodule with order number 6ES7964-2AA01-0AB0 hasan additional front cover, which is similar to the front cover of the IF 960HFsynchronization submo...

Interface Submodules 13-63 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 13.9.1 Pin Assignments X1 Connector There is a 9-pin sub D socket connector on the frontside of the submodule forplugging in the connecting cable. See Table 13-45 for the pin assignments. Table 13-...

Interface Submodules 13-64 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 13.9.2 Addressing and Interrupts In the M7-300/400-Reserved I/O Address Area The base address depends on the interface submodule slot in the expansionmodule or the programmable module. See the des...

A-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Parameter Sets for Signal Modules Chapter Overview Section Description Page A.1 How to Assign the Parameters for Signal Modules in the User Program A-2 A.2 Parameters of the Digital Input Modules A-4 A.3 Parameters of th...

Parameter Sets for Signal Modules A-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 A.1 How to Assign the Parameters for Signal Modules in the User Program Parameter Assignment in the User Program You have already assigned parameters to the modules in STEP 7. In the us...

Parameter Sets for Signal Modules A-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Description of the Parameters The following sections contain all the modifiable parameters for the various moduleclasses. The parameters of the signal modules are described: • in the onl...

Parameter Sets for Signal Modules A-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 A.2 Parameters of the Digital Input Modules Parameters The table below contains all the parameters you can set for digital input modules. You will see which parameters you can modify fr...

Parameter Sets for Signal Modules A-5 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Byte 0 7 6 0 Hardware interrupt enable Diagnostic interrupt enable Byte 1 7 6 0 On rising edge at channel 0 On rising edge at channel 2 On rising edge at channel 4 On rising edge at chan...

Parameter Sets for Signal Modules A-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 A.3 Parameters of the Digital Output Modules Parameters The table below contains all the parameters you can set for digital output modules.The comparison shows: • Which parameters you ca...

Parameter Sets for Signal Modules A-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Structure of Data Record 1 The figure below shows the structure of data record 1 (bytes 0, 1 and 2) for theparameters of the digital output modules. You enable a parameter by setting th...

Parameter Sets for Signal Modules A-11 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Structure of Data Record 1 The figure below shows the structure of data record 1 for the parameters of theanalog input modules. You enable a parameter by setting the corresponding bit t...

B-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Diagnostic Data of the Signal Modules Chapter Overview Section Description Page B.1 Evaluating the Diagnostic Data of the Signal Modules in the UserProgram B-2 B.2 Structure and Contents of Diagnostic Data Bytes 0 and 1 ...

Diagnostic Data of the Signal Modules B-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 B.1 Evaluating the Diagnostic Data of the Signal Modules in the User Program In This Appendix This Appendix describes the structure of the diagnostic data in the system data.You mus...

Diagnostic Data of the Signal Modules B-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 B.2 Structure and Contents of Diagnostic Data Bytes 0 and 1 The structure and contents of the different bytes of the diagnostic data aredescribed below. The following general rule ap...

Diagnostic Data of the Signal Modules B-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 B.3 Diagnostic Data of the Digital Input Modules as of Byte 2 The structure and contents of the different bytes of the diagnostic data for specialdigital input modules are described...

Diagnostic Data of the Signal Modules B-7 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Bytes 9 to 24 of the SM 421; DI 16 24/60 VUC Data record 1 with bytes 9 to 24 contains the channel-specific diagnostic data. Thefigure below shows the assignment of the diagnostic by...

Diagnostic Data of the Signal Modules B-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 B.4 Diagnostic Data of the Digital Output Modules as of Byte 2 The structure and contents of the different bytes of the diagnostic data for specialdigital output modules are describ...

Diagnostic Data of the Signal Modules B-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 B.5 Diagnostic Data of the Analog Input Modules as of Byte 2 The structure and contents of the different bytes of the diagnostic data for thespecial analog input modules are descri...

C-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Spare Parts and Accessories Spare Parts and Accessories For Racks Number wheel for slot labeling C79165-Z1523-A22 Spare slot covers (qty 10) 6ES7490-1AA00-0AA0 For Power Supplies Spare connector for PS 405 (DC) 6ES7490-0...

Spare Parts and Accessories C-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 For IMs Terminating connector for IM 461-0 6ES7461-0AA00-7AA0 Terminating connector for IM 461-1 6ES7461-1AA00-7AA0 Terminating connector for IM 461-3 6ES7461-3AA00-7AA0 IM 463-2, send IM, 60...

Spare Parts and Accessories C-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Cables Connecting cables for printers with • Serial port (COM, 10 m) • Parallel port (Centronics) 9AB4173-2BN10-0CA06AP1901-0AL00 Connecting cable for interface module • 1 6ES7368 3BB00 0AA0 g...

D-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Guidelines for Handling ElectrostaticSensitive Devices (ESD) Introduction In this appendix, we explain • what is meant by “electrostatic sensitive devices” • the precautions you must observe when handling and working wit...

Guidelines for Handling Electrostatic Sensitive Devices (ESD) D-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 D.1 What is ESD? Definition All electronic modules are equipped with large-scale integrated ICs or components.Due to their design, these electronic elements ...

Guidelines for Handling Electrostatic Sensitive Devices (ESD) D-3 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 D.2 Electrostatic Charging of Persons Charging Every person with a non-conductive connection to the electrical potential of itssurroundings can be charged ele...

Guidelines for Handling Electrostatic Sensitive Devices (ESD) D-4 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 D.3 General Protective Measures Against Electrostatic Discharge Damage Ensure Sufficient Grounding Make sure that the personnel, working surfaces and packagi...

E-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 List of Abbreviations Abbreviation Explanation AC Alternating current ADC Analog to digital converter AI Aanalog input AO Analog output AS Automation system BAF Battery failure BUSF1;BUSF2 LED – bus failure on the MPI/Pr...

Glossary-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Glossary Address An address denotes a specific operand or address area; examples of this are:input I 12.1; memory word MW 25; data block DB 3. Aggregate current Sum of the currents of all output channels on a digi...

Glossary Glossary-2 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Bus connector A physical connection between the bus nodes and the bus cable. Bus segment A bus segment is a self-contained section of a serial bus system. Bus segmentsare interconnected by means of ³ rep...

Glossary Glossary-8 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Ground, to To ground means to connect an electrically conductive part via a groundingsystem to the grounding electrode (one or more conductive parts having a verygood contact to ground). Hardware interru...

Glossary Glossary-9 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Interrupt, diagnostic ³ Diagnostic Interrupt Interrupt, end-of-scan-cycle ³ Hardwareinterrupt Interrupt, hardware ³ Hardware interrupt Interrupt response time The interrupt response time is the time from ...

Glossary Glossary-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Local data Local data are data assigned to a ³ code block that is declared in its ³ declaration section and its variable declaration. It includes (depending on the block): formal parameters, ³ static da...

Glossary Glossary-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Non-isolated In the case of non-isolated input/output modules, the reference potentials of thecontrol and load circuit are electrically connected. OB ³ Organization block Organization block Organization...

Glossary Glossary-13 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Priority class The operating system of an S7 CPU has a maximum of 28 priority classes(= program execution levels) – for cyclic program scanning or program scanningcontrolled by hardware interrupt, for ex...

Glossary Glossary-14 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Programming device A programming device (PG) is an industry-standard, compact personal computer.A PG is completely equipped for programming SIMATIC programmablecontrollers. Protection level The SIMATIC ...

Glossary Glossary-18 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 STARTUP The STARTUP mode is traversed during the transition from STOP mode to RUNmode.STARTUP can be triggered by the ³ mode selector or following power-on or by means of an operator input on the progra...

Glossary Glossary-20 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Warm restart This is a reboot after a power failure using a set of dynamic data programmed bythe user and a user program section defined in the system.A warm restart is indicated by setting a status bit...

Index-1 S7-400, M7-400 Programmable Controllers Module SpecificationsA5E00069467-07 Index A Accessories, C-1Accessories, M7-400, memory card, 11-8Actuator connection, to analog output module, 5-59 Actuators, connecting, 13-42ADC-DAC error, analog input module, 5-66Address, Glossary-1Address area, se...

Index Index-6 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 Functional grounding, Glossary-7Fuse blown, Glossary-7 digital module, 4-12digital output module, 4-8 G Global data, Glossary-7Ground, Glossary-7Ground short circuit, analog input module, 5-66Grounded operatio...

Index Index-10 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 PARM_MOD, SFC 57, A-2Password, M7-400, 11-31Performance features, M7-400, CPUs, 11-2Permissible potential differences, 7-3PG cable, 11-15, C-2Pin assignment, RS 485 repeater, 10-6PLC, Glossary-13Point-to-poin...

Index Index-12 S7-400, M7-400 Programmable Controllers Module Specifications A5E00069467-07 T Technical specifications IF 961-AIO, 13-54IF 961-DIO, 13-31IF 962-COM, 13-15IF 962-LPT, 13-22IF 962-VGA, 13-8IF 964-DP, 13-65IM 460-0 and 461-0, 6-9IM 460-1 and 461-1, 6-13IM 460-3 and 461-3, 6-17IM 460-4 a...