Siemens Hicom 300 E CS - Manuals

Page 2 - N e t wo r k To p o l o g y; C o n f i g u r a t i o n; Use the following steps to configure the Siemens Hicom 300 E CS PBX:

Cisco Systems, Inc. All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 2 of 34 side, the Siemens PBX must send at least 10 digits for the router to properly route the call. Otherwise, the Cisco 2621 router sends back a releas...

Page 3 - S i e m e n s H i c o m 3 3 0 E C S P B X C o n f i g u ra t i o n M e n u s a n d C o m m a n d s; Add the new access code to DPLN.; H500: AMO DPLN STARTED

Cisco Systems, Inc. All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 3 of 34 S i e m e n s H i c o m 3 3 0 E C S P B X C o n f i g u ra t i o n M e n u s a n d C o m m a n d s Step 1. Add the new access code to DPLN. <di...

Page 6 - | DIGIT INTERPRETATION VALID FOR DIAL PLAN 0 |

Page 7 - Add the new trunk board using BCSU.; H500: AMO BCSU STARTED

Cisco Systems, Inc. All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 7 of 34 Step 2. Add the new trunk board using BCSU. <dis-bcsu TYPE = tmd; DIS-BCSU:TMD; H500: AMO BCSU STARTED ----------------------------------------...

Page 8 - Configure Class of Parameter for device handler using COP.; H500: AMO COP STARTED; Add the new trunk group access code using TGACC.; H500: AMO TGACC STARTED

Cisco Systems, Inc. All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 8 of 34 Step 4. Configure Class of Parameter for device handler using COP. <dis-cop COPNO = 0; DIS-COP:0; H500: AMO COP STARTED | | | | | | | | S E A |...

Page 9 - DISPLAY; H500: AMO TCSU STARTED

Cisco Systems, Inc. All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 9 of 34 Step 6. Add the channels using TCSU. TCSU – B Channel <dis-tcsu PEN1 = 1-2-103-1; DIS-TCSU:1-2-103-1; H500: AMO TCSU STARTED +-----------------...

Page 11 - C o n f i g u r i n g t h e C i s c o C a l l M a n a g e r

Cisco Systems, Inc. All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 11 of 34 C o n f i g u r i n g t h e C i s c o C a l l M a n a g e r Figure 1 Configuring the 6608-E1 Gateway

Page 13 - R o u t e Pa tt e r n C o n f i g u r a t i o n

Cisco Systems, Inc. All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 13 of 34 R o u t e Pa tt e r n C o n f i g u r a t i o n

Page 14 - Te s t R e s u l t s; the ISDN PRI link between a Cisco 2621 and the PBX.

Cisco Systems, Inc. All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 14 of 34 Te s t R e s u l t s As shown in the diagram below, a Siemens Hicom 300 E CS PBX was connected via an ISDN T1 PRI link to a Cisco 2621, which in ...

Page 15 - link in high impedance mode.; User/Network Settings

Cisco Systems, Inc. All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 15 of 34 Test Configuration Layer 1 (Physical Layer) The Siemens configuration screen for the DS1 trunk interface is reached with the command: <cha-bss...

Page 16 - Table 3; Calls Made

Cisco Systems, Inc. All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 16 of 34 . Table 1 PBX 1 - NI2 (Network) Cisco 2621 Gateway - primary-ni(User) Siemens Hicom 330 E CSSwitch-type/ Protocol sidesetting Cisco Cisco 2621_B ...

Page 17 - Test Setup 2; Setup was as follows:; Table 4; Yes; Table 5

Cisco Systems, Inc. All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 17 of 34 Test Setup 2 Setup was as follows: • PBX1 configured as NI2, emulates User • Cisco Cisco 2621Gateway configured as PRI NI2, emulates Network Tabl...

Page 18 - A p p e n d i x A; Table 6; Switch and Gateway Settings; isdn protocol—emulate network

Cisco Systems, Inc. All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 18 of 34 . When the Cisco 2621 router is set to emulate Network side, the Siemens PBX must send at least 10 digits for the router to properly route the ca...

Page 19 - S i e m e n s H i c o m 3 3 0 E C S S o ft wa re re l e a s e; H500: AMO ANSU STARTED

Cisco Systems, Inc. All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 19 of 34 S i e m e n s H i c o m 3 3 0 E C S S o ft wa re re l e a s e ------------------------------------------------------------------------------- TER...

Page 20 - C i s c o 2 6 2 1 R o u te r C o n f i g u ra t i o n

Cisco Systems, Inc. All contents are Copyright © 1992–2002 Cisco Systems, Inc. All rights reserved. Important Notices and Privacy Statement. Page 20 of 34 C i s c o 2 6 2 1 R o u te r C o n f i g u ra t i o n 2621_B#sh ver Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-J...