Page 2 - © 2021 Seagate Technology LLC. All rights reserved.; Document Revision History; Revision
© 2021 Seagate Technology LLC. All rights reserved. Publication number: 100851637, Rev. G March 2021 Seagate, Seagate Technology and the Spiral logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Raid Rebuild and SeaTools are either trademarks or reg...
Page 3 - Seagate IronWolf Pro SATA Product Manual, Rev. G; Contents
Seagate IronWolf Pro SATA Product Manual, Rev. G 2 Contents Seagate® Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 5 - For Firmware Download and Tools Download for Secure Erase, visit:; Seagate® Technology Support Services
Seagate IronWolf Pro SATA Product Manual, Rev. G 4 For Seagate Product Support, visit: www.seagate.com/support For Seagate Compliance, Safety, and Disposal, visit: www.seagate.com/support For Firmware Download and Tools Download for Secure Erase, visit: www.seagate.com/support/downloads/ For informa...
Page 6 - Introduction; NOTE
Seagate IronWolf Pro SATA Product Manual, Rev. G 5 www.seagate.com Introduction 1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following: Seagate® IronWolf™ Pro SATA drive models. These drives provide the following key features: 256 MB data b...
Page 7 - About the Serial ATA interface; Scalability to higher performance levels.
Seagate IronWolf Pro SATA Product Manual, Rev. G 6 www.seagate.com Introduction 1.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: Easy installation and configuration with true plug-...
Page 8 - Drive specifications; the drive; Specification summary tables; Table 2 Drive specifications summary
Seagate IronWolf Pro SATA Product Manual, Rev. G 7 www.seagate.com Drive specifications 2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout thi...
Page 9 - Drive specification
Seagate IronWolf Pro SATA Product Manual, Rev. G 8 www.seagate.com Drive specifications * See Section 2.10, "Reliability" for rated MTBF device operating condition requirements. † Seagate does not recommend operating at sustained drive temperatures above 60°C. Operating at higher temperature...
Page 10 - Formatted capacity; where; Recording and interface technology
Seagate IronWolf Pro SATA Product Manual, Rev. G 9 www.seagate.com Drive specifications 2.2 Formatted capacity *One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. NOTE LBA Counts for drive capacities ...
Page 11 - Power specifications; See Figure 3 on page 20; Power requirements for the drives are listed in; Table 3; . Typical power measurements are based on an average of
Seagate IronWolf Pro SATA Product Manual, Rev. G 10 www.seagate.com Drive specifications 2.5 Power specifications The drive receives DC power (+5V or +12V ) through a native SATA power connector. See Figure 3 on page 20 . 2.5.1 Power consumption Power requirements for the drives are listed in Table ...
Page 12 - Typical current profiles; Typical 5V and 12V startup and operation current profiles; Conducted noise
Seagate IronWolf Pro SATA Product Manual, Rev. G 11 www.seagate.com Drive specifications 2.5.1.1 Typical current profiles Figure 1. Typical 5V and 12V startup and operation current profiles 2.5.2 Conducted noise Noise is specified as a periodic and random distribution of frequencies covering a band ...
Page 13 - Extended Power Conditions - PowerChoice; Power on reset
Seagate IronWolf Pro SATA Product Manual, Rev. G 12 www.seagate.com Drive specifications 2.5.4 Extended Power Conditions - PowerChoice ™ Utilizing the load/unload architecture a programmable power management interface is provided to tailor systems for reduced power consumption and performance requir...
Page 14 - PowerChoice Manufacture Default Power Condition Timer Values; Power Condition Name
Seagate IronWolf Pro SATA Product Manual, Rev. G 13 www.seagate.com Drive specifications PowerChoice provides the following reporting methods for tracking purposes Check Power Mode Command Reports the current power state of the drive Identify Device Command EPC Feature set supported flag EPC F...
Page 15 - PowerChoice Supported Extended Power Condition Identifiers; Environmental limits; Temperature; The maximum allowable drive reported temperature is 149°F (65°C).; HDA
Seagate IronWolf Pro SATA Product Manual, Rev. G 14 www.seagate.com Drive specifications PowerChoice Supported Extended Power Condition Identifiers 2.6 Environmental limits Temperature and humidity values experienced by the drive must be such that condensation does not occur on any drive part. Altit...
Page 16 - Humidity; Shock; a. Linear Random Operating Vibration
Seagate IronWolf Pro SATA Product Manual, Rev. G 15 www.seagate.com Drive specifications 2.6.2 Humidity The values below assume that no condensation on the drive occurs. Maximum wet bulb temperature is 84.2°F (29°C). 2.6.2.1 Relative humidity 2.6.3 Effective Altitude (sea level) 2.6.4 Shock and Vibr...
Page 17 - Acoustics; Electromagnetic immunity
Seagate IronWolf Pro SATA Product Manual, Rev. G 16 www.seagate.com Drive specifications 2.7 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound power measurements are taken under esse...
Page 18 - Reliability; HDA temperature as reported by the drive <= 30°C
Seagate IronWolf Pro SATA Product Manual, Rev. G 17 www.seagate.com Drive specifications 2.10 Reliability 2.10.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) The production disk drive shall achieve an annualized failure-rate of 0.73% (MTBF of 1,200,000 hours) over a 5 year ser...
Page 19 - HDD and SSD Regulatory Compliance and Safety; For the latest regulatory and compliance information see:; Regulatory Models; Regulatory Model Numbers: STL008; Corrosive environment
Seagate IronWolf Pro SATA Product Manual, Rev. G 18 www.seagate.com Drive specifications 2.11 HDD and SSD Regulatory Compliance and Safety For the latest regulatory and compliance information see: www.seagate.com/support/ scroll down the page to the Compliance, Safety and Disposal Guide link. 2.11.1...
Page 20 - Reference documents; Supported Standards; Product warranty; number is required to determine remaining warranty information.; Shipping
Seagate IronWolf Pro SATA Product Manual, Rev. G 19 www.seagate.com Drive specifications 2.13 Reference documents Supported Standards Serial ATA Revision 3.3 specification ANSI Documents INCITS 529-2018 ATA/ATAPI Command Set - 4 (ACS-4) Specification for Acoustic Test Requirement and Procedures Seag...
Page 21 - Configuring and mounting the drive; Handling and static-discharge precautions; See; Table 6; attached to the drive or host.; Figure 3; Attaching SATA cabling; Caution
Seagate IronWolf Pro SATA Product Manual, Rev. G 20 www.seagate.com Configuring and mounting the drive 3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static-discharge precautions After unpackin...
Page 22 - Drive mounting; Figure 4; when mounting the drive:; Mechanical specifications; Refer to; Mounting configuration dimensions
Seagate IronWolf Pro SATA Product Manual, Rev. G 21 www.seagate.com Configuring and mounting the drive 3.4 Drive mounting Users can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. See Figure 4 for drive mounting dimensions....
Page 23 - Hot-Plug compatibility; The drive motor must come to a complete stop; (Ready to spindle stop time indicated in; Serial ATA device plug connector pin definitions
Seagate IronWolf Pro SATA Product Manual, Rev. G 22 www.seagate.com Serial ATA (SATA) interface 4.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0...
Page 24 - Supported ATA commands; Table 7 Supported ATA commands
Seagate IronWolf Pro SATA Product Manual, Rev. G 23 www.seagate.com Serial ATA (SATA) interface Notes: 1. All pins are in a single row, with a 1.27mm (0.050”) pitch. 2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are...
Page 25 - Command name
Seagate IronWolf Pro SATA Product Manual, Rev. G 24 www.seagate.com Serial ATA (SATA) interface Read Sectors 20 H Read Sectors Extended 24 H Read Verify Sectors 40 H Read Verify Sectors Extended 42 H Receive FPDMA Queued 65 H Request Sense Data Ext 0B H Remove Element And Truncate 7C H Sanitize Devi...
Page 27 - Identify Device command; The Identify Device command (command code EC; Table 7; on; see Section 2.0 on page 7; for default parameter settings.
Seagate IronWolf Pro SATA Product Manual, Rev. G 26 www.seagate.com Serial ATA (SATA) interface 4.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of dat...
Page 28 - Table 8
Seagate IronWolf Pro SATA Product Manual, Rev. G 27 www.seagate.com Serial ATA (SATA) interface 60–61 Total number of user-addressable LBA sectors available (see Section 2.2 for related information) *Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors, 137GB). Drives wit...
Page 31 - . All reserved bits or words should be set to zero.
Seagate IronWolf Pro SATA Product Manual, Rev. G 30 www.seagate.com Serial ATA (SATA) interface 4.3.2 Identify Device Data log The IDENTIFY DEVICE Data log (log 30H) transfers information about the drive. The data is organized as a set of 512-byte blocks of data, whose contents are shown in Table 2 ...
Page 32 - Table 9 Identify Device Data log
Seagate IronWolf Pro SATA Product Manual, Rev. G 31 www.seagate.com Serial ATA (SATA) interface 02 Capacity 0..7 Capacity page information header (QWord) 63 Shall be set to 1 1 62:24 Reserved 23:16 Page number 02 15:0 Revision number 0001 8..15 Device Capacity (QWord) 63 Shall be set to 1 1 62:48 Re...
Page 45 - Table 10 Device Statistics log
Seagate IronWolf Pro SATA Product Manual, Rev. G 44 www.seagate.com Serial ATA (SATA) interface 05 Temperature Statistics Current Temperature Yes Average Short Term Temperature Yes Average Long Term Temperature Yes Highest Temperature Yes Lowest Temperature Yes Highest Average Short Term Temperature...
Page 46 - Set Features command values
Seagate IronWolf Pro SATA Product Manual, Rev. G 45 www.seagate.com Serial ATA (SATA) interface 4.3.4 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features regi...
Page 47 - Draft; Code in features register
Seagate IronWolf Pro SATA Product Manual, Rev. G 46 www.seagate.com Serial ATA (SATA) interface 4.3.5 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradatio...
Page 48 - Seagate Technology LLC
Seagate Technology LLC AMERICAS Seagate Technology LLC 47488 Kato Road, Fremont, California 94538, United States, 510-661-1000 Publication Number: 100851637, Rev. G March 2021
SEAGATE ST16000NM002G
User Manual
SEAGATE ST2000VX015
User Manual
SEAGATE ST6000VN001
User Manual
SEAGATE ST8000VN004
User Manual
SEAGATE ST8000VX004
User Manual
SEAGATE STJL2000400
User Manual
SEAGATE STKM1000400
User Manual