Schneider Electric iEM3100 - Manuals

iEM3100 / iEM3200 / iEM3300 series user manual DOCA0005EN-04 3 The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein. This documentation is not intended as a substitute for and is not to be us...

Page 4 - Safety information; Important information; DANGER; WARNING; result in death or; CAUTION; result in minor or; NOTICE; be used with this signal word.

4 DOCA0005EN-04 iEM3100 / iEM3200 / iEM3300 series user manual Safety information Important information Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service or maintain it. The following special messages may appear ...

Page 5 - Notices; FCC Part 15 notice; Reorient or relocate the receiving antenna.

iEM3100 / iEM3200 / iEM3300 series user manual DOCA0005EN-04 5 Notices FCC Part 15 notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful ...

Page 6 - About the book; Document scope; This function meets the requirements for:; Related documents

6 DOCA0005EN-04 iEM3100 / iEM3200 / iEM3300 series user manual About the book Document scope This manual is intended for use by designers, system builders and maintenance technicians with an understanding of electrical distribution systems and monitoring devices. Validity note The meters are used to...

Page 7 - Contents

iEM3100 / iEM3200 / iEM3300 series user manual DOCA0005EN-04 7 Contents Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 9 - Chapter 1; Carefully read and follow the safety precautions outlined below.; HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH; See NFPA 70E in the USA or applicable local standards.; UNINTENDED OPERATION; INACCURATE DATA RESULTS; practices or equipment maintenance.

iEM3100 / iEM3200 / iEM3300 series user manual Safety precautions DOCA0005EN-04 9 Chapter 1 Safety precautions Installation, wiring, testing and service must be performed in accordance with all local and national electrical codes. Carefully read and follow the safety precautions outlined below. DANG...

Page 11 - Chapter 2; What is in this chapter?; This chapter contains the following topics:; Overview of meter functions; The key features of the meters are:; Main characteristics

iEM3100 / iEM3200 / iEM3300 series user manual Overview DOCA0005EN-04 11 Chapter 2 Overview What is in this chapter? This chapter contains the following topics: Overview of meter functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Typical applicatio...

Page 13 - Typical applications; iEM32•• series

iEM3100 / iEM3200 / iEM3300 series user manual Overview DOCA0005EN-04 13 Typical applications This range is a cost effective solution to monitor feeder circuits. These meters can monitor energy consumption by usage, by zone or by feeder in the cabinet. They can be used to monitor feeders in a main s...

Page 15 - Chapter 3; Dimensions; iEM33•• meters

iEM3100 / iEM3200 / iEM3300 series user manual Hardware and installation DOCA0005EN-04 15 Chapter 3 Hardware and installation What is in this chapter? This chapter contains the following topics: Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 16 - Hardware overview; All meters: Meter sealing points

16 DOCA0005EN-04 Hardware and installation iEM3100 / iEM3200 / iEM3300 series user manual Hardware overview All meters: Meter sealing points All meters have sealing covers and sealing points to help prevent access to inputs and outputs and current and voltage connections. iEM3100 / iEM3110 / iEM3115...

Page 17 - iEM3135 - Direct measurement up to 63 A and M-Bus communications; The various features of the iEM3135 are shown in the diagram below:

iEM3100 / iEM3200 / iEM3300 series user manual Hardware and installation DOCA0005EN-04 17 iEM3135 - Direct measurement up to 63 A and M-Bus communications The various features of the iEM3135 are shown in the diagram below: iEM3150 / iEM3155 / iEM3165 - Direct measurement up to 63 A and Modbus or BAC...

Page 18 - The various features of the iEM3175 are shown in the diagram below:

18 DOCA0005EN-04 Hardware and installation iEM3100 / iEM3200 / iEM3300 series user manual iEM3175 - Direct measurement up to 63 A and LonWorks communications The various features of the iEM3175 are shown in the diagram below: iEM3200 / iEM3210 / iEM3215 - Measurement with CTs The various features of...

Page 19 - iEM3235 - Measurement with CTs and M-Bus communications

iEM3100 / iEM3200 / iEM3300 series user manual Hardware and installation DOCA0005EN-04 19 iEM3235 - Measurement with CTs and M-Bus communications The various features of the iEM3235 (CTs 1 A or 5 A with M-Bus communications) are shown in the diagram below: iEM3250 / iEM3255 / iEM3265 - Measurement w...

Page 20 - iEM3275 - Measurement with CTs and LonWorks communications

20 DOCA0005EN-04 Hardware and installation iEM3100 / iEM3200 / iEM3300 series user manual iEM3275 - Measurement with CTs and LonWorks communications The various features of the iEM3275 (CTs 1 A or 5 A with LonWorks communications) are shown in the diagram below: iEM3300 / iEM3310 - Direct measuremen...

Page 21 - iEM3335 - Direct measurement up to 125 A and M-Bus communications; The various features of the iEM3335 are shown in the diagram below:

iEM3100 / iEM3200 / iEM3300 series user manual Hardware and installation DOCA0005EN-04 21 iEM3335 - Direct measurement up to 125 A and M-Bus communications The various features of the iEM3335 are shown in the diagram below: iEM3350 / iEM3355 / iEM3365 - Direct measurement up to 125 A and Modbus or B...

Page 22 - The various features of the iEM3375 are shown in the diagram below:; DIN rail mounting and dismounting; Mounting the meter on a DIN rail

22 DOCA0005EN-04 Hardware and installation iEM3100 / iEM3200 / iEM3300 series user manual iEM3375 - Direct measurement up to 125 A and LonWorks communications The various features of the iEM3375 are shown in the diagram below: DIN rail mounting and dismounting Mounting the meter on a DIN rail 1. Pos...

Page 23 - Dismounting the meter from a DIN rail; Lift the meter out and up to free it from the DIN rail.

iEM3100 / iEM3200 / iEM3300 series user manual Hardware and installation DOCA0005EN-04 23 Dismounting the meter from a DIN rail 1. Use a flat-tip screwdriver ( ≤ 6.5 mm / 0.25 in) to lower the locking mechanism and release the meter. 2. Lift the meter out and up to free it from the DIN rail. Click!

Page 24 - Input, output and communications wiring; Related topics; The pulse output is compatible with S0 format.

24 DOCA0005EN-04 Hardware and installation iEM3100 / iEM3200 / iEM3300 series user manual Input, output and communications wiring This section describes the wiring of the digital inputs, digital and pulse outputs and the communications (as applicable). Related topics • See “Power system wiring” on p...

Page 25 - The digital input and output are electrically independent.

iEM3100 / iEM3200 / iEM3300 series user manual Hardware and installation DOCA0005EN-04 25 Digital input wiring: iEM3135 / iEM3155 / iEM3165 / iEM3175 / iEM3235 / iEM3255 / iEM3265 / iEM3275 / iEM3335 / iEM3355 / iEM3365 / iEM3375 • The digital input and output are electrically independent. Digital o...

Page 26 - The LON communications connection is polarity-independent.; Power system wiring; Voltage input protection; NOTE: Ground any unused current inputs on 1 A and 5 A meters.; iEM31•• and iEM33•• devices associated with a contactor; The meter must be protected by a circuit breaker.

26 DOCA0005EN-04 Hardware and installation iEM3100 / iEM3200 / iEM3300 series user manual LonWorks communications wiring: iEM3175 / iEM3275 / iEM3375 • The LON communications connection is polarity-independent. Power system wiring The diagrams below illustrate how to connect the meters to a single-p...

Page 27 - 3 A direct measurement meter wiring; Fuses and disconnect switch

iEM3100 / iEM3200 / iEM3300 series user manual Hardware and installation DOCA0005EN-04 27 Related topics • See “Input, output and communications wiring” on page 24 for information on wiring the digital inputs, digital or pulse outputs and communications for your device. 63 A direct measurement meter...

Page 28 - 25 A direct measurement meter wiring

28 DOCA0005EN-04 Hardware and installation iEM3100 / iEM3200 / iEM3300 series user manual 125 A direct measurement meter wiring Fuses and disconnect switch DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH • Do not connect N’ to the load when setting the wiring type on the meter to 1PH4W Mult...

Page 29 - A / 1 A meter wiring; Single-phase systems with CTs; 50 mA fuses and disconnect switch; the CT before removing the connection from the meter.

iEM3100 / iEM3200 / iEM3300 series user manual Hardware and installation DOCA0005EN-04 29 5 A / 1 A meter wiring Single-phase systems with CTs 250 mA fuses and disconnect switch Shorting block 3PH4W DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH • Do not connect N’ to the load when setting...

Page 30 - Three-phase systems with CTs

30 DOCA0005EN-04 Hardware and installation iEM3100 / iEM3200 / iEM3300 series user manual Three-phase systems with CTs 250 mA fuses and disconnect switch Shorting block indicates wiring for a balanced system 1PH2W L-L 1PH3W L-L-N 1PH multiple loads with neutral (1PH4W Multi L-N) 1 2CTs 3CTs 1 The 1P...

Page 31 - Three-phase systems with CTs and VTs

iEM3100 / iEM3200 / iEM3300 series user manual Hardware and installation DOCA0005EN-04 31 Three-phase systems with CTs and VTs 250 mA fuses and disconnect switch Shorting block VT primary fuses and disconnect switch indicates wiring for a balanced system Power system Wiring 3PH3W 2 VTs, 1 CT 2 VTs, ...

Page 33 - Chapter 4; Data display screen overview

iEM3100 / iEM3200 / iEM3300 series user manual Front panel display and meter setup DOCA0005EN-04 33 Chapter 4 Front panel display and meter setup What is in this chapter? This chapter contains the following topics: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 34 - Example: navigating the display screens; Partial Reactive E; Data display screens

34 DOCA0005EN-04 Front panel display and meter setup iEM3100 / iEM3200 / iEM3300 series user manual Example: navigating the display screens 1. Press to scroll through the main display screens; in the image above, press to move from Partial Reactive E to Tariffs to V & I . 2. Press to access addi...

Page 35 - See “Resets” on page 36 for more information on meter resets.

iEM3100 / iEM3200 / iEM3300 series user manual Front panel display and meter setup DOCA0005EN-04 35 Data display screens: iEM3150 / iEM3250 / iEM3350 Related topics • See “Troubleshooting” on page 103 for more information on the Diagnosis screen and a list of diagnostic codes. • See “Resets” on page...

Page 36 - Resets; Resetting accumulated energy using the display; Multi Tariff feature

36 DOCA0005EN-04 Front panel display and meter setup iEM3100 / iEM3200 / iEM3300 series user manual Related topics • See “Troubleshooting” on page 103 for more information on the Diagnosis screen and a list of diagnostic codes. • See “Resets” on page 36 for more information on meter resets. Resets T...

Page 37 - Meter status information; The device clock; Clock behavior on power interruption; Date

iEM3100 / iEM3200 / iEM3300 series user manual Front panel display and meter setup DOCA0005EN-04 37 Meter status information Two LEDs on the front panel indicate the current status of the device: the green status LED and the yellow energy pulsing LED. The icons in the table below indicate the LED st...

Page 38 - Setting the clock initially; Device configuration; The default factory settings are listed in the following table:; Entering configuration mode; and; ESC; at the same time for about 2 seconds.; Access Counter; screen displays, indicating the; The front panel display in configuration mode

38 DOCA0005EN-04 Front panel display and meter setup iEM3100 / iEM3200 / iEM3300 series user manual Setting the clock initially The following diagram illustrates how to set the clock when you initially power up the device or after a power failure. To set the clock during normal operation, see the se...

Page 39 - Com. Protection setting; Modifying parameters; Selecting a value from a list; Example: Configuring a list value; Frequency; Modifying a numerical value

iEM3100 / iEM3200 / iEM3300 series user manual Front panel display and meter setup DOCA0005EN-04 39 Related topics • See “Modifying parameters” on page 39 for instructions on using the front panel buttons to configure list and numeric value settings. • See “Configuration mode menus” on page 40 for a...

Page 40 - Example: configuring a numeric value; Canceling an entry; Configuration mode menus

40 DOCA0005EN-04 Front panel display and meter setup iEM3100 / iEM3200 / iEM3300 series user manual The parameters listed below are the only ones for which you set a numerical value (if the parameter is available on your device): • Date • Time • Pick Up Value for an overload alarm • Voltage Transfor...

Page 46 - Configuration menus for iEM3250

46 DOCA0005EN-04 Front panel display and meter setup iEM3100 / iEM3200 / iEM3300 series user manual Configuration menus for iEM3250 Multi Tariffs (iEM3215) Control Mode Disableby Internal Clock Select the tariff control mode:• Disable: the Multi Tariff function is disabled. • by Digital Input: the d...

Page 51 - Chapter 5; This chapter contains the following sections:; Modbus communication overview; There are three different ways of using Modbus communication:; Modbus communications settings

iEM3100 / iEM3200 / iEM3300 series user manual Communications via Modbus RS-485 DOCA0005EN-04 51 Chapter 5 Communications via Modbus RS-485 What is in this chapter? This chapter contains the following sections: Modbus communication overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 52 - Modbus functions; Function list; Unit table

52 DOCA0005EN-04 Communications via Modbus RS-485 iEM3100 / iEM3200 / iEM3300 series user manual Modbus functions Function list The table below lists the supported Modbus functions: For example: • To read different parameters from the meter, use function 3 (Read). • To change the tariff, use functio...

Page 53 - Command interface; Command interface overview; The following table describes a Modbus command request:; Command result; The following table describes the command result:

iEM3100 / iEM3200 / iEM3300 series user manual Communications via Modbus RS-485 DOCA0005EN-04 53 DATETIME format: Command interface Command interface overview The command interface allows you to configure the meter by sending specific command requests using Modbus function 16. Command request The fo...

Page 54 - Command list; Set Wiring

54 DOCA0005EN-04 Communications via Modbus RS-485 iEM3100 / iEM3200 / iEM3300 series user manual Command list Set Date/Time Set Wiring Command Number Action (R/W) Size Type Unit Range Description 1003 W 1 UInt16 — — (Reserved) W 1 UInt16 — 2000–2099 Year W 1 UInt16 — 1–12 Month W 1 UInt16 — 1–31 Day...

Page 56 - Communications Setup

56 DOCA0005EN-04 Communications via Modbus RS-485 iEM3100 / iEM3200 / iEM3300 series user manual Input Metering Setup (iEM3155 / iEM3255 / iEM3355) Overload Alarm Setup (iEM3155 / iEM3255 / iEM3355) Communications Setup Command Number Action (R/W) Size Type Unit Range Description 6014 W 1 UInt16 – –...

Page 57 - Reset Partial Energy Counters; Modbus register list; System

iEM3100 / iEM3200 / iEM3300 series user manual Communications via Modbus RS-485 DOCA0005EN-04 57 Reset Partial Energy Counters Reset Input Metering Counter (iEM3155 / iEM3255 / iEM3355) Modbus register list System Meter Setup and Status Command Number Action (R/W) Size Type Unit Range Description 20...

Page 58 - Command Interface

58 DOCA0005EN-04 Communications via Modbus RS-485 iEM3100 / iEM3200 / iEM3300 series user manual Energy Pulse Output Setup (iEM3155 / iEM3255 / iEM3355) Command Interface Communication Input Metering Setup (iEM3155 / iEM3255 / iEM3355) 2031 R/WC 1 UInt16 A CT SecondaryNot applicable for iEM3150 / iE...

Page 59 - Meter Data

iEM3100 / iEM3200 / iEM3300 series user manual Communications via Modbus RS-485 DOCA0005EN-04 59 Digital Input (iEM3155 / iEM3255 / iEM3355) Digital Output (iEM3155 / iEM3255 / iEM3355) Meter Data Current, voltage, power, power factor and frequency 7052 R/WC 2 Float32 pulse/unit Pulse Constant 7055 ...

Page 60 - Energy, energy by tariff and input metering

60 DOCA0005EN-04 Communications via Modbus RS-485 iEM3100 / iEM3200 / iEM3300 series user manual Energy, energy by tariff and input metering Most energy values are available in both signed 64-bit integer and 32-bit floating point format. The energy and energy by tariff measurements listed below are ...

Page 61 - Read Device Identification

iEM3100 / iEM3200 / iEM3300 series user manual Communications via Modbus RS-485 DOCA0005EN-04 61 Overload Alarm (iEM3155 / iEM3255 / iEM3355) Read Device Identification The meters supports the Read Device Identification function with the mandatory objects VendorName, ProductCode and Revision Number....

Page 62 - The Read Device ID codes 01 and 04 are supported:

62 DOCA0005EN-04 Communications via Modbus RS-485 iEM3100 / iEM3200 / iEM3300 series user manual The Read Device ID codes 01 and 04 are supported: • 01 = request to get basic device identification (stream access) • 04 = request to get one specific identification object (individual access) The Modbus...

Page 63 - Chapter 6; LonWorks communications overview; LonWorks communication implementation; The LonMaker plug-ins; Red service LED; This LED provides the status of LonWorks operations.

iEM3100 / iEM3200 / iEM3300 series user manual Communications via LonWorks DOCA0005EN-04 63 Chapter 6 Communications via LonWorks What is in this chapter? This chapter contains the following sections: LonWorks communications overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 64 - Green communications LED; Location of the service pin and Neuron ID; General variables

64 DOCA0005EN-04 Communications via LonWorks iEM3100 / iEM3200 / iEM3300 series user manual Green communications LED This LED provides the status of the meter’s communications with the network. Location of the service pin and Neuron ID The service pin is located on the front panel. Press this when r...

Page 65 - Energy and energy by tariff measurements

iEM3100 / iEM3200 / iEM3300 series user manual Communications via LonWorks DOCA0005EN-04 65 Related topics • See “Troubleshooting” on page 103 for more information on the error codes. • See “Network propagation rate setup” on page 70 for information on variables that control the network update rate....

Page 66 - See “Resets” on page 68 for information on resetting values.

66 DOCA0005EN-04 Communications via LonWorks iEM3100 / iEM3200 / iEM3300 series user manual Related topics • See “Resets” on page 68 for information on resetting values. • See “Network propagation rate setup” on page 70 for information on variables that control the network update rate. Instantaneous...

Page 68 - Meter configuration properties; the meter over communications.

68 DOCA0005EN-04 Communications via LonWorks iEM3100 / iEM3200 / iEM3300 series user manual Related topics • See “Meter configuration properties” on page 68 for information on SCPTs and UCPTs that you can use to configure the meter. • See “Echelon LonMaker plug-in for data display and meter configur...

Page 69 - Basic setup

iEM3100 / iEM3200 / iEM3300 series user manual Communications via LonWorks DOCA0005EN-04 69 Basic setup Digital input setup Input metering setup Function profile UCPT Struct Members Range / options Description nciCfgWiring UCPTWiring SystemType 0, 1, 2, 3, 11, 13 0 = 1PH2W L-N1 = 1PH2W L-L2 = 1PH3W ...

Page 70 - Overload alarm setup

70 DOCA0005EN-04 Communications via LonWorks iEM3100 / iEM3200 / iEM3300 series user manual Overload alarm setup Multi Tariff setup Network propagation rate setup The following configuration properties help control network traffic by controlling the rate at which variable values are sent to your LNS...

Page 71 - Installing and registering the LonMaker plug-in; Make sure Echelon LonMaker is closed.; if you want to; Next; to begin the installation.

iEM3100 / iEM3200 / iEM3300 series user manual Communications via LonWorks DOCA0005EN-04 71 Echelon LonMaker plug-in for data display and meter configuration The information in this section assumes that you have an advanced understanding of system administration using Echelon LonMaker. The LonMaker ...

Page 72 - Close; Browsing the meter using the LonMaker plug-in; Browse; LonMaker plug-in interface

72 DOCA0005EN-04 Communications via LonWorks iEM3100 / iEM3200 / iEM3300 series user manual A screen appears when the installation is complete. Click Close . 5. Navigate to Start > Programs > Schneider Electric and select the registration entry for the plug- in you installed (for example, Schn...

Page 75 - Chapter 7; M-Bus communications overview; Configuring basic communications settings

iEM3100 / iEM3200 / iEM3300 series user manual Communications via M-Bus DOCA0005EN-04 75 Chapter 7 Communications via M-Bus What is in this chapter? This chapter contains the following sections: M-Bus communications overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 76 - M-Bus protocol support; The meter supports the M-Bus protocol as follows:; M-Bus protocol implementation; M-Bus tool for viewing data and configuring the meter

76 DOCA0005EN-04 Communications via M-Bus iEM3100 / iEM3200 / iEM3300 series user manual Related topics • See the M-Bus organization website at www.m-bus.com for more information on the M-bus protocol. • See “Hardware overview” on page 16 for the location of the communications LED. • See “Communicat...

Page 77 - Variable data structure telegram information; Fixed data header; x in the hex value is determined by bits 7-4 of the DIF.; Primary VIF used by the meter

iEM3100 / iEM3200 / iEM3300 series user manual Communications via M-Bus DOCA0005EN-04 77 Variable data structure telegram information Fixed data header Data record header information Data formats used by the meter (DIF bits 3-0) NOTE: x in the hex value is determined by bits 7-4 of the DIF. Data fun...

Page 78 - Manufacturer-specific VIFE codes

78 DOCA0005EN-04 Communications via M-Bus iEM3100 / iEM3200 / iEM3300 series user manual Manufacturer-specific VIFE codes The manufacturer-specific VIFE codes in the table below are used by the meter when the VIF equals FF hex (1111 1111 bin). NOTE: E denotes the extension bit; the hex value assumes...

Page 79 - Telegram information for data records; Primary VIF in hex; Meter information

iEM3100 / iEM3200 / iEM3300 series user manual Communications via M-Bus DOCA0005EN-04 79 Telegram information for data records The following sections outline the telegram information used in data records. The tables contain the following information (if applicable): • Data format in hex (for example...

Page 80 - Instantaneous measurements; Date and time information

80 DOCA0005EN-04 Communications via M-Bus iEM3100 / iEM3200 / iEM3300 series user manual Instantaneous measurements NOTE: E denotes the extension bit; the hex value assumes E = 0. Meter status information Use the following information to read system and status information from the meter. See the sec...

Page 81 - Power system configuration information

iEM3100 / iEM3200 / iEM3300 series user manual Communications via M-Bus DOCA0005EN-04 81 Power system configuration information NOTE: E denotes the extension bit; the hex value assumes E = 0. Digital input and output status information NOTE: E denotes the extension bit; the hex value assumes E = 0. ...

Page 82 - Alarm status information; Telegram information for meter configuration; Supported VIFE codes for meter configuration

82 DOCA0005EN-04 Communications via M-Bus iEM3100 / iEM3200 / iEM3300 series user manual Alarm status information NOTE: E denotes the extension bit; the hex value assumes E = 0. Telegram information for meter configuration You can use the information provided in this section to write to the meter us...

Page 83 - Power system setup

iEM3100 / iEM3200 / iEM3300 series user manual Communications via M-Bus DOCA0005EN-04 83 Date/time setup Power system setup NOTE: E denotes the extension bit; the hex value assumes E = 0. Multi Tariff setup NOTE: E denotes the extension bit; the hex value assumes E = 0. Data format Primary VIF Descr...

Page 84 - Communications setup

84 DOCA0005EN-04 Communications via M-Bus iEM3100 / iEM3200 / iEM3300 series user manual Communications setup To change the baud rate via communications, send a telegram to the meter with the appropriate value in the CI-field: Digital input setup NOTE: E denotes the extension bit; the hex value assu...

Page 85 - M-Bus tool for data display and meter configuration; Installing the M-Bus tool

iEM3100 / iEM3200 / iEM3300 series user manual Communications via M-Bus DOCA0005EN-04 85 Use the information in the table below to acknowledge the overload alarm. NOTE: E denotes the extension bit; the hex value assumes E = 1. Resets NOTE: E denotes the extension bit; the hex value assumes E = 1. M-...

Page 86 - Test Com; Viewing meter data using the M-Bus tool; Interval

86 DOCA0005EN-04 Communications via M-Bus iEM3100 / iEM3200 / iEM3300 series user manual 2. Select the port on your computer that you are using to connect to the meter and select the baud rate that matches the meter’s configuration. 3. Click Test Com to open the communications port. 4. Type the devi...

Page 87 - Configuring the meter using the M-Bus tool; Send

iEM3100 / iEM3200 / iEM3300 series user manual Communications via M-Bus DOCA0005EN-04 87 Configuring the meter using the M-Bus tool 1. Select Setup > Config to switch to configuration mode. 2. Set the values that you want to change then click Send for that value or section. For example, to change...

Page 89 - Chapter 8; BACnet communications overview; Key terms; BACnet protocol support; The meter supports the BACnet protocol as follows:

iEM3100 / iEM3200 / iEM3300 series user manual Communications via BACnet DOCA0005EN-04 89 Chapter 8 Communications via BACnet What is in this chapter? This chapter contains the following sections: BACnet communications overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 90 - The following standard object types are supported:; BACnet communications implementation; Configuring basic communication parameters

90 DOCA0005EN-04 Communications via BACnet iEM3100 / iEM3200 / iEM3300 series user manual The following standard object types are supported: Related topics • See “Device object” on page 91 for information on the proprietary properties in the Device object. BACnet communications implementation Config...

Page 91 - Communications LED indicator for BACnet meters; BACnet object and property information; Device object

iEM3100 / iEM3200 / iEM3300 series user manual Communications via BACnet DOCA0005EN-04 91 Make sure that the Mac Address is unique on the serial loop and the Device ID is unique in your BACnet network. Communications LED indicator for BACnet meters The LED indicates the status of the meter’s communi...

Page 92 - Analog Input objects; The Value Type for all AI objects is Real.

92 DOCA0005EN-04 Communications via BACnet iEM3100 / iEM3200 / iEM3300 series user manual Related topics • See “Device configuration” on page 38 for information on configuring the meter using the front panel. Analog Input objects The following tables list the Analog Input (AI) objects along with the...

Page 94 - Communications settings information

94 DOCA0005EN-04 Communications via BACnet iEM3100 / iEM3200 / iEM3300 series user manual Communications settings information The following AI objects display information about the meter’s communications settings. NOTE: You can access the meter’s communications configuration information over BACnet ...

Page 95 - Analog Value object; The Value Type for all BI objects is Boolean.

iEM3100 / iEM3200 / iEM3300 series user manual Communications via BACnet DOCA0005EN-04 95 Analog Value object There is one Analog Value (AV) object available on the meter, named AV00 - Command. The available commands are listed in the following table. Enter the number in the Present_Value column in ...

Page 97 - Chapter 9; Electrical characteristics; Power system inputs: iEM31•• meters

iEM3100 / iEM3200 / iEM3300 series user manual Specifications DOCA0005EN-04 97 Chapter 9 Specifications What is in this chapter? This chapter contains the following sections: Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97...

Page 98 - Power system inputs: iEM32•• meters

98 DOCA0005EN-04 Specifications iEM3100 / iEM3200 / iEM3300 series user manual Power system inputs: iEM32•• meters Inputs and outputs Characteristic Value Voltage inputs Measured voltage Wye: 100 - 277 V L-N, 173 - 480 V L-L ±20%Delta: 173 - 480 V L-L ±20% Overload 332 V L-N or 575 V L-L Impedance 3...

Page 99 - Mechanical characteristics

iEM3100 / iEM3200 / iEM3300 series user manual Specifications DOCA0005EN-04 99 Mechanical characteristics Environmental characteristics Measurement accuracy Programmable digital input Number 2 iEM3115 / iEM3215 1 iEM3135 / iEM3155 / iEM3165 / iEM3175 / iEM3235 / iEM3255 / iEM3265 / iEM3275 / iEM3335...

Page 100 - MID; LonWorks communications

100 DOCA0005EN-04 Specifications iEM3100 / iEM3200 / iEM3300 series user manual MID Complies with the European Measuring Instruments Directive (MID) 2004/22/CE when installed in a suitable switchboard in accordance with the instructions in DOCA0038EN, available on our website. The CE declaration doc...

Page 101 - BACnet communications

iEM3100 / iEM3200 / iEM3300 series user manual Specifications DOCA0005EN-04 101 Related topics • See “Communications via LonWorks” on page 63 for information on LonWorks communications. M-Bus communications Related topics • See “Communications via M-Bus” on page 75 for information on M-Bus communica...

Page 103 - Troubleshooting; Do not open the meter. Opening the meter voids the warranty.; Diagnosis screen; The Diagnosis screen lists any current diagnostic codes.; Diagnosis; RISK OF DAMAGE TO THE METER

iEM3100 / iEM3200 / iEM3300 series user manual Troubleshooting DOCA0005EN-04 103 Chapter 10 Troubleshooting The meter does not contain any user-serviceable parts. If the meter requires service, contact your local Schneider Electric representative. Do not open the meter. Opening the meter voids the w...

Page 104 - Diagnostic codes

104 DOCA0005EN-04 Troubleshooting iEM3100 / iEM3200 / iEM3300 series user manual Diagnostic codes If the diagnostics code persists after following the instructions below, please contact Technical Support. 1 Not all diagnostic codes apply to all devices. Diagnostic code 1 Description Possible solutio...

Page 105 - Power, energy and power factor; Power and the PQ coordinate system; Quadrant 3

iEM3100 / iEM3200 / iEM3300 series user manual Power, energy and power factor DOCA0005EN-04 105 Chapter 11 Power, energy and power factor NOTE: The descriptions in this section assume that you are an electrical energy consumer, not a supplier. What is in this chapter? This chapter contains the follo...

Page 106 - True PF and displacement PF; True power factor includes harmonic content.; PF lead / lag convention; Current phase shift from voltage; P F

106 DOCA0005EN-04 Power, energy and power factor iEM3100 / iEM3200 / iEM3300 series user manual Energy delivered (imported) / energy received (exported) The meter interprets energy delivered (imported) or received (exported) according to the direction of real power (P) flow. Energy delivered (import...

Page 107 - Power and PF lead / lag; PF sign convention; PF sign in IEC

iEM3100 / iEM3200 / iEM3300 series user manual Power, energy and power factor DOCA0005EN-04 107 Power and PF lead / lag PF lead / lag summary PF sign convention The meter shows positive or negative power factor according to IEC standards. PF sign in IEC The meter correlates power factor sign (PF sig...

Page 108 - Power factor register format; PF value

108 DOCA0005EN-04 Power, energy and power factor iEM3100 / iEM3200 / iEM3300 series user manual Power factor register format Each power factor value (PF value) occupies one floating point register for power factor (PF register). The meter performs a simple algorithm to the PF value then stores it in...

Page 112 - Schneider Electric

Schneider Electric 35, rue Joseph MonierCS30323F - 92506 Rueil Malmaison Cedexwww.schneider-electric.com As standards, specifications and designs change from time to time, please ask for confirmation of the information given in this publication.© 2014 Schneider Electric. All rights reserved.DOCA0005...