Samsung WW90T304MWW - Manuals

English   5 Safety information These warning signs are here to prevent injury to yourself and others.Please follow them explicitly.After reading this manual, store it in a safe place for future reference. Read all instructions before using the appliance. As with any equipment that uses electricity a...

6   English Safety information Safety information 4. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly quali fi ed persons in order to avoid a hazard. 5. The new hose-sets supplied with the appliance are to be used and old hose-sets should not be ...

English   7 Safety information Critical installation warnings WARNING The installation of this appliance must be performed by a quali fi ed technician or service company. • Failure to do so may result in electric shock, fi re, an explosion, problems with the product, or injury. The appliance is heav...

8   English Safety information Safety information Do not use an electric transformer. • This may result in electric shock or fi re. Do not use a damaged power plug, damaged power cord, or loose wall socket. • This may result in electric shock or fi re. Do not pull or excessively bend the power cord....

English   9 Safety information Critical usage warnings WARNING If the appliance is fl ooded, turn off the water & power supplies immediately and contact your nearest service centre. • Do not touch the power plug with wet hands. • Failure to do so may result in electric shock. If the appliance ge...

10   English Safety information Safety information Do not unplug the appliance by pulling the power cord. Always grip the plug fi rmly and pull it straight out of the outlet. • Damage to the power cord may cause a short-circuit, fi re and/or electric shock. Do not attempt to repair, disassemble, or ...

English   13 Safety information Do not use natural hand-washing soap for the washing machine. • If it hardens and accumulates inside the washing machine, it may result in problems with the product, discolouration, rust, or bad odours. Place socks and brassieres in a washing net and wash them with th...

14   English Safety information Safety information Instructions about the WEEE Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in countries with separate collection systems) This marking on the product, accessories or literature indicates that the product a...

English   15 Installation Installation Follow these instructions carefully to ensure proper installation of the washing machine and to prevent accidents when doing laundry. What’s included Make sure all the parts are included in the product package. If you have a problem with the washing machine or ...

English   17 Installation Installation requirements Electrical supply and grounding• AC 220-240 V / 50 Hz fuse or circuit breaker is required • Use an individual branch circuit speci fi c to the washing machine To ensure proper grounding, the washing machine comes with a power cord featuring a three...

English   19 Installation Step-by-step installation STEP 1   Select a location Location requirements:• Solid, level surface without carpeting or fl ooring that may obstruct ventilation • Away from direct sunlight • Adequate room for ventilation and wiring • The ambient temperature is always higher t...

20   English Installation Installation STEP 2   Remove the shipping bolts Unpack the product package and remove all shipping bolts. NOTE Number of shipping bolts may differ depending on the model. WARNING • Packaging materials can be dangerous to children. Dispose all packaging material (plastic bag...

22   English Installation Installation STEP 3   Adjust the levelling feet 1. Gently slide the washing machine into position. Excessive force may damage the levelling feet. 2. Level the washing machine by manually adjusting the levelling feet. 3. When levelling is complete, tighten the nuts using the...

English   23 Installation STEP 4   Connect the water hose The provided water hose may differ depending on the model. Please follow the instruction according to the provided water hose. Connecting to a threaded water tap 1. Connect the water hose to the water tap, and then turn it to the right to tig...

English   27 Installation STEP 5   Position the drain hose The drain hose can be positioned in three ways: A Over the edge of a wash basin The drain hose must be placed at a height of between 60 cm and 90 cm (*) from the fl oor. To keep the spout of the drain hose bent, use the supplied plastic hose...

28   English Installation Installation In a sink drain pipe branch The drain pipe branch must be above the sink siphone so that the end of the hose is at least 24 in. (60 cm) above the ground.(*) : 24 in. (60 cm) CAUTION Remove the lid on the sink drain pipe branch before connecting the drain pipe t...

English   29 Befor e y ou start Before you start Initial settings Make sure your washing machine is installed properly before using it.You must complete a wash cycle without clothes before washing clothes for the fi rst time. 1. Connect the water hoses to the water tap and the washing machine. 2. Pl...

30   English Befor e y ou start Before you start STEP 2   Empty pockets Empty all the pockets of your laundry items• Metal objects such as coins, pins, and buckles on clothing may damage other laundry items as well as the drum. Turn clothing with buttons and embroideries inside out• If pants or jack...

English   31 Befor e y ou start STEP 6   Apply a proper detergent type The type of detergent depends on the type of fabric (cotton, synthetic, delicate items, wool), colour, wash temperature, and degree of soiling. Always use “low suds” laundry detergent, which is designed for automatic washing mach...

English   33 Befor e y ou start Detergent recommendation The recommendations apply to the temperature ranges given in the cycle chart.  Recommended  Liquid detergent only – Not recommended  Powder detergent only Cycle Detergent Temp. (°C) Universal Delicates and woollens Specialist ECO 40-60  – ...

34   English Befor e y ou start Before you start Detergent drawer guidelines The washing machine provides a three-compartment dispenser: the left compartment for the main wash, the center for fabric softeners, and the right for the preliminary wash. 01 Prewash compartment : Apply prewash detergent o...

English   37 Oper ations Operations Control panel 6040 01 Cycle Selector Turn the dial to select a cycle. 02 Display The display shows current cycle information and estimated time remaining, or an information code when a problem occurs. 03 Temp. Press to change the water temperature for the current ...

38   English Oper ations Operations Simple steps to start 6040 1. Press Power to turn on the washing machine. 2. Turn the Cycle Selector to select a cycle. 3. Change the cycle settings ( Temp. and Spin ) as necessary. 4. Set Delay End if you want to fi nish the wash cycle at the desired time. 5. Pre...

English   39 Oper ations Cycle overview Standard cycles Cycle Description Max load (kg) 9 kg model 8 kg model COTTON • For cottons, bed linens, table linens, underwear, towels, or shirts.The washing time and the rinse count are automatically adjusted according to the load. • For cleaning lightly soi...

English   41 Oper ations Delay End You can set the washing machine to fi nish your wash automatically at a later time, choosing a delay of between 3 to 24 hours (in 1 hour increments). The hour displayed indicates the time the wash will fi nish. 1. Select a cycle. Then change the cycle settings if n...

42   English Maint enanc e Maintenance Keep the washing machine clean to prevent deteriorated performance and to preserve its life cycle. Emergency drain In case of a power failure, drain the water inside the drum before taking out the laundry. A 1. Power off and unplug the washing machine from the ...

English   43 Maint enanc e Cleaning Surface of the washing machine Use a soft cloth with a nonabrasive household detergent. Do not spray water onto the washing machine. Mesh fi lter Clean the mesh fi lter of the water hose once or twice a year. 1. Turn off the washing machine, and unplug the power c...

46   English Maint enanc e Maintenance Recovery from freezing The washing machine may freeze when it drops below 0 °C. 1. Turn off the washing machine, and unplug the power cord. 2. Pour warm water over the water tap to loosen the water hose. 3. Disconnect the water hose, and soak it in warm water. ...

English   47 Troubleshooting Troubleshooting Checkpoints If you encounter a problem with the washing machine, fi rst check the table below and try the suggestions. Problem Action Does not start. • Make sure the washing machine is plugged in. • Make sure the door is properly closed. • Make sure the w...

English   51 Troubleshooting Information codes If the washing machine fails to operate, you may see an information code on the screen. Check the table below and try the suggestions. Code Action 4C Water is not supplied.• Make sure the water taps are open. • Make sure the water hoses are not clogged....

English   53 Speci fi cations Speci fi cations Fabric care chart The following symbols provide garment care directions. The care labels include four symbols in this order: washing, bleaching, drying and ironing (and dry cleaning when necessary). The use of symbols ensures consistency among garment m...

54   English Speci fi cations Speci fi cations Protecting the environment • This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a pow...

56   English Speci fi cations Speci fi cations Indicative information (According to EU 2019/2023) Model Program Capacity (kg) Program Time (HH:MM) Energy Consumption (kWh/Cycle) Water Consumption (L/cycle) Maximum Temperature (°C) Remaining Moisture Content (%) Spinning Speed (RPM) WT9*T3*4*** ECO 4...

Memo WW3000TM_8-9KG_UK_8C104-000601_EN.indd 57 WW3000TM_8-9KG_UK_8C104-000601_EN.indd 57 2021-01-29 1:46:05 2021-01-29 1:46:05

2 _ Safety Instructions WARNING WHILE SERVICING • Check if the power plug and outlet are damaged, flattened, cut or otherwise degraded. 4 If faulty, replace it immediately. Failing to do so may result in electric shock or fire. • Completely remove any dust or foreign material from the housing, wirin...

Safety Instructions _ 3 CAUTION BEFORE SERVICING • Do not sprinkle water onto the washing machine directly when cleaning it. 4 This may result in electric shock or fire, and may shorten the product lifetime. • Do not place any containers with water or any other liquid on the washing machine 4 If the...

4 _ Features and Specifications 2. FEATURES AND SPECIFICATIONS 2-1. SPECIFICATIONS MODEL WW7*T30*** WW8*T301*** WW9*T304*** Model name Front loading washing machine Dimensions (mm) 595*495*850 595*520*850 595*560*850 Water pressure 50kPa-800kPa Net weight (kg) 59 59 64 Wash and spin capacity 7kg 8kg...

Features and Specifications _ 5 2-2. COMPARING SPECIFICATIONS WITH EXISTING MODELS Project WW3000TM Model Name WW9*T304*** WW8*T30**** WW7*T30**** Image Feature - - - Capacity 9.0kg 8.0 kg 7.0 kg Main Spec Drum Volume 60 L 53 L 49 L Max Rpm 1400 rpm 1400 / 1200 rpm 1200, 1400 / 1200, 1400 rpm Motor ...

6 _ Features and Specifications 2-3. ACCESSORIES Figure Unit Code QTY Description Bolt Spanner - 1 To remove the shipping bolts To adjust the leveling leg Assy Hose Water - Cold only 1 ( ★ ) To setup water supply. Hose Water (Aqua-Stop) - 1( ★ ) To setup water supply. Cap Fixer - 4 To cover the hole...

Disassembly and Reassembly _ 7 3. DISASSEMBLY AND REASSEMBLY 3-1. TOOLS FOR DISASSEMBLY AND REASSEMBLY Tool Type Remarks Box driver 10mm Heater(1),Tub(12), Fixer screw(4), Motor(2), 13mm Shock Absorber (3 holes each in left/right), Damper(3), Damper(friction 2), Balance(6) 17mm Pulley(1) Double-ende...

8 _ Disassembly and Reassembly 3-2. STANDARD DISASSEMBLY DRAWINGS ► This is a standard disassembly diagram and may differ from the actual product. Use this material as a reference when disassembling and reassembling the product.  Disassembly Part Figure Description Assy Cover Top 1. Remove 2 screws...

Disassembly and Reassembly _ 9  Reassembly Part Figure Description Assy Drawer 1. Fit the hole and press the Cap Rinse so that it can be assembled. 2. Make sure to fit the rail when reassembling the Assy Drawer. 3. Insert the Drawer as shown in the picture.

10 _ Disassembly and Reassembly  Disassembly Part Figure Description Assy Panel Control 1. Remove 2 screws holding the Drawer and Panel using (+) screw driver. 2. Remove the 2 screws at the top of the Assy Panel Control using (+) screw driver. 3. If you hold the Panel and pull it forward, the Hook ...

Disassembly and Reassembly _ 11  Reassembly Part Figure Description Assy Panel Control 1. Insert the 7 Wire Connectors into PBA and fix the 2 Cable Ties. Make sure the Hook is locked properly. 2. Assemble the Assy Panel Control to the product. 3. Assemble the 2 screws on both sides of the Assy Pane...

12 _ Disassembly and Reassembly  Disassembly Part Figure Description Assy Housing-Drawer 1. Separate the Clamp. 2. Remove the Hose Drawer Tub fixed to the Assy Housing-Drawer. 3. Separate the Clamp fixed to the Tub. 4. Remove the 2 Connectors and 2 screws fixed to the Water Valve.

Disassembly and Reassembly _ 13 Part Figure Description Assy Housing-Drawer 1. Separate the all Clamps. 2. Separate the 6 Hooks from both sides of Housing-Drawer. Be careful not to break the Hook.

14 _ Disassembly and Reassembly  Reassembly Part Figure Description Assy Housing-Drawer 1. Assemble the 6 Hooks on both sides of Housing-Drawer. 2. First, assemble the Hose to the Water Valve and Housing-Drawer and then fix the Clamps. 3. After mounting the Assy Housing-Drawer on the product, assem...

Disassembly and Reassembly _ 15 Part Figure Description Assy Housing-Drawer 4. Assemble the Hose Drawer Tub to Assy Housing-Drawer. 5. Assemble the Clamp.

16 _ Disassembly and Reassembly  Disassembly Part Figure Description Water Valve 1. Separate the Assy Cover Top.2. Separate the 2 Connectors and Clamps by hand and remove 2 Hoses with long nose pliers. 3. Remove the 2 screws holding the Water Valve using (+) screw driver.  Reassembly Part Figure D...

Disassembly and Reassembly _ 17  Disassembly Part Figure Description Frame Front Before you start, disassemble Assy Cover Top, Assy Panel Control. Be careful not to tear up the Diaphragm. 1. Using long nose pliers, pick up one of the rings on Wire-Diaphragm which connect the spring and the wire end...

18 _ Disassembly and Reassembly Part Figure Description Frame Front 4. Remove the 2 screws and separate the Assy Door. 5. Separate the Door S/W by pressing the molded object above and below Door S/W. 6. Open the Hook on the upper part of the Filter Cover by pressing it down with a (-) screw driver o...

Disassembly and Reassembly _ 19  Reassembly Part Figure Description Frame Front 1. Assemble the 8 Hooks by checking the direction of the Guide Filter. 2. After fixing the Cover Filter to the lower 2 places of the Guide Filter, press the upper part to assemble. 3. Assemble by pressing Door S/W in li...

20 _ Disassembly and Reassembly Part Figure Description Frame Front 5. Fasten the 5 screws in the upper 2 places and the lower 3 places. 6. Assemble the Door Diaphragm on Frame Front. 7. Fix the Clamp.

Disassembly and Reassembly _ 21  Disassembly Part Figure Description Assy Door Open the Door. Remove the 2 screws fixed to the Frame Front and Door using a (+) screw driver. Remove 10 screws using a (+) screwdriver, and remove by inserting an awl into the Holder.

22 _ Disassembly and Reassembly Part Figure Description Assy Door Remove 4 screws with (+) screw driver and disassemble the Door Hinge and Door Lever assembled in Holder and then separate the Door Glass from Holder Glass Hook.

Disassembly and Reassembly _ 23  Reassembly Part Figure Description Assy Door Insert the Door Glass into the Holder Glass to fit the groove and fasten the door lever with two screws and then assemble the Hinge Door to Holder and fasten with 2 screws. Assemble the Cover Door to Holder Glass and fast...

24 _ Disassembly and Reassembly  Disassembly Part Figure Description Door-Lock S/W Before you start, disassemble Assy Cover Top, Assy Panel Control. Be careful not to tear up the Diaphragm. 1. Using long nose pliers, pick up one of the rings on Wire-Diaphragm which connect the spring and the wire e...

Disassembly and Reassembly _ 25  Reassembly Part Figure Description Door-Lock S/W Insert the Connector of Door Lock S/W. Insert the 2 Holders of Door Lock S/W into the Hole of Frame Front. Fasten the 5 screws in the upper 2 places and the lower 3 places.

26 _ Troubleshooting 4. TROUBLESHOOTING 4-1. INFORMATION CODE ► When an abnormal condition occurs, melody sounds and displays Info. code indications as shown in the following Info. codes are shown until the status has cleared. No. Information Type Information Code Causes Corrective Actions 1 Water L...

Wiring Diagram _ 29 5. WIRING DIAGRAM 5-1. WIRING DIAGRAM ► This Document can not be used without Samsung’s authorization. n REFERENCE INFORMATION BLK BLACK BLU BLUE GRN GREEN GRY GRAY NTR NATURAL ORG ORANGE PNK PINK RED RED SKYBLU SKYBLUE VIO VIOLET WHT WHITE YEL YELLOW