Samsung WA10H7200GW - User Manual

English - 7 Do not touch the power plug with wet hands.- This may result in electric shock. Do not turn the appliance off by unplugging the power plug while the washer is in operation.- Plugging the power plug into the wall socket again may cause a spark and result in electric shock or fire. Keep al...

English - 9 Do not place any non-laundry objects, such as shoes, food waste, or animals into the washer. - This can cause abnormal vibrations that can damage the washer, and, in the case of pets, cause severe injury or death. Do not press the buttons using sharp objects such as pins, knifes, fingern...

English - 10 installing your washer unpAckinG your WAsHer Unpack your washer and inspect it for shipping damage. Make sure you have received all the items shown below. If your washer was damaged during shipping, or you do not have all of the items, contact 1300-362- 603 .To prevent personal injury o...

English - 11 bAsic locAtion requirements Electrical • 220-240 Volt 50 Hz 15 AMP fuse or circuit breaker • Individual branch circuit serving only your Washer is recommended. • Your Washer is equipped with a power cord. NEVER USE AN EXTENSION CORD. Grounding ELECTRICAL GROUNDING IS REQUIRED FOR THIS A...

English - 12 installing your washer 2 in. (5.1 cm) 6 in (15.2 cm) 29.3 in (74.4 cm) B 21 in. (53.3 cm) Case 1. 3.9 in (10 cm). Case 2. 2.8 in (7 cm). 1 in. (2.5 cm) Drain facility The recommended height of the standpipe is 39 in / 99 cm. The drain hose must be routed through the drain hose clip to t...

English - 13 Required dimensions for Installation * required spacing importAnt note to instAller Please read the following instructions carefully before installing your washer.These instructions should be retained for future reference.We recommend you hire a professional to install this washer. sTep...

English - 14 sTep 2 Connecting the water and the drain connecting the water supply hose Before installing the water supply hoses, make sure there are rubber gaskets inside the fittings at both ends of each new water hose. Installing the water supply hoses without rubber gaskets can cause water leaka...

English - 15 Connecting the drain hose The end of the drain hose can be positioned in three ways: over the edge of a wash basin Secure the guide to the side of the basin wall with a hook or to the tap with a piece of string to prevent the drain hose from moving. in a standpipe or laundry tub The sta...

English - 16 sTep 4 Powering your washer Plug the power cord into a 3-prong, well grounded 220-240 volt 50 Hz approved electrical outlet protected by a 15-amp fuse or comparable circuit breaker.Your washer is grounded through the third prong of the power cord when plugged into a three-prong grounded...

English - 17 operating instructions warning: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: loAdinG your WAsHer • You can fill the tub with dry, unfolded clothes, but DO NOT OVERLOAD the tub, No more than...

English - 18 washing a load of laundry overvieW of tHe control pAnel cycle selector Select the appropriate cycle for the type of load.The cycle you select determines the tumble pattern and spin speed for the cycle. To minimize wrinkling of laundry, select the Perm Press cycle. cotton - For averagely...

English - 21 Sound The Sound Off function can be selected during all cycles. When this function is selected, sound is turned off for all cycles. Even if the power is turned on and off repeatedly, the setting is retained. Garment+ You can add or take out laundry items even after the wash has started,...

English - 23 Washing clothes using the cycle selector Your new washing machine makes washing clothes easy, using Samsung’s “Fuzzy Control” automatic control system. When you select a wash program, the machine will set the correct temperature, washing time, and washing speed. 1. Press the power butto...

English - 24 deterGent use • The use a good quality top loader detergent is recommended. • It is also important to: Pre–treat stains before washing. Sort clothes by color. Sort clothes by the amount of soiling. Avoid overloading. When using powdered detergent it is recommended that the powder be dis...

English - 26 maintaining your washer cleAninG tHe exterior Turn off the water faucets after finishing the day’s washing.This will shut off the water supply to your washer and prevent the unlikely possibility of damage from escaping water. Leave the lid open to allow the inside of your washer to dry ...

English - 27 cleAninG tHe filter Diamond ( magic ) filter screen 1. Press your thumb on the upper bayonet of Diamond (magic) filter screen, then push down and pull outward to open the cover. 2. Remove the residues. 3. Clean with water. 4. Reassembly the Diamond (magic) filter screen.Point the bottom...

English - 28 cleAninG tHe dispensers The automatic dispenser may need to be cleaned periodically due to laundry additive buildup. 1. Pull the dispenser drawer straight back until it stops. 2. Tilt the dispenser drawer upward and remove it. 3. Remove the inserts from the 3 compartments. Rinse the ins...

English - 29 tub cleAn Tub Clean is a self-cleaning cycle that removes mold that may occur inside the washing machine. 1. Press the power button. 2. Select the Tub clean cycle. • Once the Tub Clean cycle is selected, the only function that can be set is Delay End. 3. Press the start/pause button. • ...

English - 30 troubleshooting cHeck tHese solutions if your WAsHer… problem soluTion Will not start. • Make sure the lid is closed. • Make sure your washer is plugged in. • Make sure the water source faucets are open. • Make sure to press the Start/Pause button to start your Washer. • Make sure Child...

English - 32 informAtion codes The Washer may display information codes to help you understand what is occurring with your Washer better. code symbol meaning soluTion 1e The Water Level sensor is not working properly. When washer displays “1E”, washer will drain for 3 minutes. At this time, the Powe...

English - 33 code symbol meaning soluTion 8e 8e2 Mems sensor problem. Call for service. te1 Temperature sensor problem. Restart the cycle.If the code reappears, call for service. oe A fault is detected in the water level sensor. Call for service. 4e2 This occurs when the temperature exceeds 50 degre...

English - 34 appendix fAbric cAre cHArt The following symbols provide garment care direction. The Clothing care labels include symbols for washing, bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures consistency among garment manufacturers of domestic and import...

English - 35 cycle cHArt Use this chart to set the best cycle and options for you laundry. (  : factory setting,  : selectable) cycle functions water level rinse (1-5) Temp. 1 2 3 4 5 6 7 h w c coTTon        2    delicaTes        2   heaVy duTy        2    baby care  ...

memo WA7000HG_WA10H_USER MANUAL_DC68-03133X_EN.indd 37 2014/8/12 11:43:10

QUESTIONS OR COMMENTS? country call or VisiT us online aT AUSTRALIA 1300 362 603 www.samsung.com/au/support Code No. DC68-03133X_EN WA7000HG_WA10H_USER MANUAL_DC68-03133X_EN.indd 40 2014/8/12 11:43:10