Samsung WD10T534DBW - Manuals

English English   5 Important safety precautions WARNING To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following:1. This appliance is not intended for use by persons (including children) with reduced physical, sens...

English English   7 23. This appliance is intended to be used in household only and it is not intended to be used such as: ‒ staff kitchen areas in shops, offices and other working environments; ‒ farm houses; ‒ by clients in hotels, motels and other residential type environments; ‒ bed and breakfas...

English Safety information English 8 Do not install this appliance in a humid, oily or dusty location, or in a location exposed to direct sunlight or water (rain drops).Do not install this appliance in a location exposed to low temperatures.• Frost may cause the tubes to burst.Do not install this ap...

English English   9 Critical usage warnings WARNING If the appliance is flooded, turn off the water & power supplies immediately and contact your nearest service centre.• Do not touch the power plug with wet hands.• Failure to do so may result in electric shock.If the appliance generates a stran...

English Safety information English 10 Do not attempt to repair, disassemble, or modify the appliance yourself.• Do not use a fuse (such as copper, steel wire, etc.) other than a standard fuse.• When the appliance needs to be repaired or reinstalled, contact your nearest service centre.• Failure to d...

English Safety information English 12 Also, do not allow children to play around the washing machine or touch the door glass. • This may result in burns.Do not insert your hand into the detergent drawer.• This may result in injury as your hand may be caught by the detergent input device.Remove the l...

English English   13 Sort the laundry by colour on the basis of its colorfastness and select the recommended cycle, water temperature and additional functions.• This may result in discolouration or fabric damage.Take care that children’s fingers are not caught in the door when you close it.• Failure...

English English 14 Installation Follow these instructions carefully to ensure proper installation of the washing machine and to prevent accidents when doing laundry. What’s included Make sure all the parts are included in the product package. If you have a problem with the washing machine or the par...

English Installation English 16 Installation requirements Electrical supply and grounding • Use an individual branch circuit specific to the washing machine. To ensure proper grounding, the washing machine comes with a power cord featuring a three-prong grounding plug for use in a properly installed...

English English   17 Flooring For best performance, the washing machine must be installed on a solid floor. Wood floors may need to be reinforced to minimise vibration and/or unbalanced loads. Carpeting and soft tile surfaces do not resist vibration well and may cause the washing machine to move sli...

English Installation English 18 Step-by-step installation STEP 1  Select a location Location requirements:• Solid, level surface without carpeting or flooring that may obstruct ventilation• Away from direct sunlight• Adequate room for ventilation and wiring• The ambient temperature is always higher ...

English Installation English 20 B 3. Insert the bolt caps (B) to the holes (marked with circle in the figure). U-PJT_COMBO-AD_SimpleUX_WEB_SSEC-02__EU_English.indd 20 2022/4/16 11:05:17

English English   21 STEP 3  Adjust the levelling feet 1. Gently slide the washing machine into position. Excessive force may damage the levelling feet. 2. Level the washing machine by manually adjusting the levelling feet. 3. When levelling is complete, tighten the nuts using the spanner. CAUTION W...

English Installation English 22 STEP 4  Connect the water hose The provided water hose may differ depending on the model. Please follow the instruction according to the provided water hose. Connecting to a threaded water tap 1. Connect the water hose to the water tap, and then turn it to the right t...

English English   23 Connecting to a non-threaded water tap A B 1. Remove the adaptor (A) from the water hose (B) . 2. Use a Phillips screwdriver to loosen four screws on the adaptor. C 3. Hold the adaptor and turn part (C) in the arrow direction to loosen it by 5 mm (*). C 4. Insert the adaptor ont...

English Installation English 26 STEP 5  Position the drain hose The drain hose can be positioned in three ways: A Over the edge of a wash basin The drain hose must be placed between 60 cm and 90 cm (*) above from the floor. To keep the spout of the drain hose bent, use the supplied plastic hose guid...

English English   27 In a sink drain pipe branch The drain pipe branch must be above the sink siphon so that the end of the hose is at least 60 cm above the ground.(*) : 60 cm CAUTION Remove the lid on the sink drain pipe branch before connecting the drain pipe to it. STEP 6  Power on Plug the power...

English English 28 Before you start NOTE Before doing your laundry for the first time, you must run a complete wash cycle without any items in the drum. Initial setup • When you turn on the washing machine for the first time, the screen shows the initial setup process. Follow the on-screen instructi...

English English   29 Laundry guidelines STEP 1  Sort Sort the laundry according to these criteria: • Care Label: Sort the laundry into cottons, mixed fibres, synthetics, silks, wools, and rayon.• colour: Separate whites from colours.• Size: Mixing different sized items together in the drum improves ...

English English   31 Laundry capsules To get the best results from using laundry capsules, please follow these instructions. 1. Put the capsule in the bottom of the empty drum towards the rear. 2. Put the laundry in the drum on top of the capsule. CAUTION For cycles using cold water or cycles that c...

English Before you start English 32 Detergent recommendation The recommendations apply to the temperature ranges given in the cycle chart.  Recommended  Liquid detergent only – Not recommended  Powder detergent only Cycle Detergent Temp. (°C) Universal Delicates and woollens Specialist Eco 40-60 ...

English English   33 Detergent drawer guidelines The automatic dispenser models provide a three-compartment dispenser: two compartments for auto-dispensing and another part for manual input. With the automatic dispensing option on, the washing machine dispenses an adequate amount of detergent or fab...

English Before you start English 34 CAUTION • Do not operate the washing machine with the compartments not placed in the detergent drawer. - A water leak may cause electric shock or injury. • Do not use the following types of detergent in the drawer. - Tablet, capsule, ball, or net types. • Do not u...

English English   37 Operations NOTE The cycle and function names that appeared in this manual may differ from your product. Control panel 01 03 02 04 10 05 06 07 08 09 01 Power Tap to turn the washing machine on or off.• If you do not manipulate the control panel for 10 minutes after the washing ma...

English Operations English 38 10 Smart Control Tap to activate or deactivate the Smart Control function.Tap and hold to enter pairing mode to connect to the SmartThings app.• When the Smart Control function is activated, you can control your washing machine remotely using the SmartThings app on your...

English English   39 Cycle overview Cycle descriptions Cycle Description Max load (kg) WD1* WD9* WD8* WD7* Eco 40-60 • For cleaning normally soiled cotton items which are declared to be washable at 40 °C or 60 °C, together in the same cycle. This cycle is used to assess the compliance with the EU Ec...

English Operations English 42 Additional functions Using Additional Functions 1. Tap . 2. Turn the Navigation dial to select the desired additional function. 3. Tap to change the selected function’s settings or start the function. NOTE • To return to the main screen, tap again or turn the Navigation...

English English   43 Prewash You can add a preliminary washing cycle before the main wash cycle. 1. Select a cycle and change the cycle settings as necessary. 2. Tap . 3. Turn the Navigation dial to select Prewash , and then tap . 4. Tap and hold . Bubble Soak This function helps remove a wide varie...

English Operations English 44 My Cycles Add or remove cycles to create a personal cycle list. 1. Tap . 2. Turn the Navigation dial to select My Cycles , and then tap . - You can only edit a cycle to create a personal cycle when the washing machine is not operating. 3. Turn the Navigation dial to sel...

English English   45 Child Lock To prevent children or infants from accidentally starting or setting the washing machine, Child Lock locks all buttons except for and . 1. Tap . 2. Turn the Navigation dial to select Child Lock , and then tap . 3. Tap to select On or Off . - The Child Lock icon turns ...

English Operations English 46 System functions Using System Functions 1. Tap and hold for 3 seconds. 2. Turn the Navigation dial and select the desired system function, and then tap . 3. Tap to change the selected function’s settings or start the function. NOTE To return to the main screen, tap agai...

English English   47 Alarm You can turn on or off the melody of cycle completion. However, the other sounds stay active. 1. Tap and hold for 3 seconds. 2. Turn the Navigation dial to select Alarm , and then tap . 3. Tap to select On or Off . - The default setting is On. NOTE The setting remains unch...

English Operations English 48 Language You can change the system language. 1. Tap and hold for 3 seconds. 2. Turn the Navigation dial to select Language , and then tap . 3. Turn the Navigation dial to select the desired language, and then tap . Factory Reset You can reset the washing machine. 1. Tap...

English Operations English 50 • Check your router if you experience any Internet connection problem after connecting your washing machine with the SmartThings app. • If the Wi-Fi is off, tap and hold for 3 seconds to enter the System functions menu, and select Wi-Fi to turn it on. • Turning the wash...

English English   51 SmartThings Wi-Fi connection On your smartphone or tablet, go to Settings and turn on the wireless connection and select an AP (Access Point).• This appliance supports the Wi-Fi 2.4 GHz protocols. Download On an app market (Google Play Store, Apple App Store, Samsung Galaxy Apps...

English Operations English 52 Open Source Announcement The software included in this product contains open source software. You may obtain the complete corresponding source code for a period of three years after the last shipment of this product by contacting our support team via http://opensource.s...

English Maintenance English 54 Emergency drain In case of a power failure, drain the water inside the drum before taking out the laundry. 1. Power off and unplug the washing machine from the electrical outlet. 2. Open the filter cover . - TYPE 1: Push down the latch of the filter cover to open. - TY...

English English   55 Cleaning Surface of the washing machine Use a soft cloth with a nonabrasive household detergent. Do not spray water onto the washing machine. AddWash door (applicable models only) A 1. Open the AddWash door. 2. Use a wet cloth to clean the AddWash door. - Do not use cleaning age...

English Maintenance English 56 Mesh filter Clean the mesh filter of the water hose once or twice a year. 1. Turn off the washing machine, and unplug the power cord. 2. Close the water tap. 3. Loosen and disconnect the water hose from the back of the washing machine. Cover the hose with a cloth to pr...

English English   57 Debris filter It is advisable to clean the debris filter every 2 months to prevent its clogging. A clogged debris filter may reduce the bubble effect. 1. Turn off the washing machine, and unplug the power cord. 2. Drain the remaining water inside the drum. See the Emergency drai...

English Maintenance English 58 Detergent drawer To prevent the detergent residue buildup in the detergent drawer, clean the detergent drawer once or twice a month, and whenever you refill or change the detergent or softener. CAUTION • Make sure to turn off the washer and unplug the power cord before...

English English   59 4. Insert the detergent drawer back into the washing machine. NOTE • Make sure the drawer recess is completely dry before inserting the detergent drawer. • Cover the tops of both compartments and re-insert them into the drawer. CAUTION Do not spray water into the detergent drawe...

English Maintenance English 60 Defrosting your washing machine The washing machine may freeze when it drops below 0 °C. 1. Turn off the washing machine, and unplug the power cord. 2. Pour warm water over the water tap to loosen the water hose. 3. Disconnect the water hose, and soak it in warm water....

English English   61 Troubleshooting If there is any problem, check the information message on the LCD screen and follow the on-screen instructions.If the problem persists, please contact the service center. Checkpoints If you encounter a problem with the washing machine, first check the table below...

English English   65 Information codes If the washing machine fails to operate, you may see an information code on the screen. Check the table below and try the suggestions. Code Action Check drainage Water is not draining.• Make sure the drain hose is not frozen or clogged.• Make sure the drain hos...

English Troubleshooting English 66 Code Action AddWash door is open (applicable models only) This message appears when you open the AddWash door without tapping and holding . If this happens, do one of the following:• Press the AddWash door to close properly. Then, tap and hold and try again. • To a...

English English   67 Code Action AC6 Check communications between the main and the inverter PBAs.• Depending on the state, the machine may automatically returns to normal operation. • Turn the machine off, and restart the cycle.• If the information code remains, contact a customer service centre. DC...

English English 68 Specifications Fabric care chart The following symbols provide garment care direction. The Clothing care labels include symbols for drying, bleaching, drying and ironing, or dry cleaning when necessary. The use of symbols ensures consistency among garment manufacturers of domestic...

English English   69 Ironing Iron at maximum sole plate temperature of 200 °C.Iron at maximum sole plate temperature of 150 °C.Iron at maximum sole plate temperature of 110 °C. Caution when using steam irons (work without steam).Do not iron. NOTE The dots indicate the temperature ranges for ironing ...

English Specifications English 70 Spare parts guarantee We guarantee that the following spare parts will be available to professional repairers and end-users for a minimum period of 10 years after placing the last unit of the model on the market.• Door, door hinges and seals, other seals, door locki...

English English   71 Type Front loading washing machine Model name WD1*T***** Dimensions A (Width) 600 mm B (Height) 850 mm C (Depth) 600 mm D 690 mm (WD**T*8****, WD**T*5****) 680 mm (WD**T*3****, WD**T*0****) E 1120 mm Water pressure 50-1000 kPa Net weight 80 kg Maximum load capacity Washing and s...

English English   77 Model Cycles Capacity (kg) Program Time (HH:MM) Energy Consumption (kWh/Cycle) Water Consumption (L/ cycle) Maximum Temperature (°C) Remaining Moisture Content (%) Spinning Speed (RPM) WD7*T****** Eco 40-60 7 3:28 1.130 63.0 44 53.0 1400 3.5 2:42 0.547 36.0 35 53.0 1400 2 2:42 0...

English English 78 Contact information QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT UK 0333 000 0333 www.samsung.com/uk/support IRELAND (EIRE) 0818 717100 www.samsung.com/ie/support GERMANY 06196 77 555 77 www.samsung.com/de/support FRANCE 01 48 63 00 00 www.samsung.com/fr/support SPAIN...

English English   79 COUNTRY CALL OR VISIT US ONLINE AT ROMANIA *8000 (apel in retea) 08008-726-78-64 (08008-SAMSUNG) Apel GRATUIT Atenţie: Dacă efectuaţi apelul din reţeaua Digi (RCS/RDS), vă rugăm să ne contactaţi formând numărul Telverde fără ultimele două cifre, astfel: 0800872678. www.samsung.c...

2 _ Safety Instructions WARNING WHILE SERVICING • Check if the power plug and outlet are damaged, flattened, cut or otherwise degraded. 4 If faulty, replace it immediately. Failing to do so may result in electric shock or fire. • Completely remove any dust or foreign material from the housing, wirin...

Safety Instructions _ 3 CAUTION BEFORE SERVICING • Do not sprinkle water onto the washing machine directly when cleaning it. 4 This may result in electric shock or fire, and may shorten the product lifetime. • Do not place any containers with water or any other liquid on the washing machine 4 If the...

Features and Specifications _ 4 2. FEATURES AND SPECIFICATIONS 2-1. SPECIFICATIONS MODEL WD90T654DBH WD10T734DBH WD90T984DSH WD80T534DBN WD70T4046EW Model Name Front loading washing machine Water Pressure 50kPa-800kPa NET weight (kg) 68 80 86 68 63 Wash & Spin Capacity 9 10.5 9 8 7 Dry Capacity ...

5 _ Features and Specifications 2-2. COMPARING SPECIFICATIONS WITH EXISTING MODELS Model name WD90T654DBH WD10T734DBH WD90T984DSH WD80T534DBN WD70T4046EW WD10K64**** Image Capacity 9 10.5 9 8 7 10.2 Dry Capacity 6 6 6 5 4 6 Main Spec Drum Volume 63 70.5 65.9 58 60.1 63 Max RPM 1400 1400 1400 1400 14...

Features and Specifications _ 6 2-3. OPTIONS SPECIFICATIONS NO Item Code QTY Remarks 1 FASTENER-BOLT DC60-00104A 1 Default 2 CAP-FIXER DC67-00307A 4(8kg model)5(9kg model) For specific models only 3 CAP-FIXER DC67-00208B 1 For specific models only 4 ASSY HOSE WATER DC97-16921A ★ For specific models ...

Disassembly and Reassembly _ 7 3. DISASSEMBLY AND REASSEMBLY 3-1. TOOLS FOR DISASSEMBLY AND REASSEMBLY Tool Type Remarks Box driver 10mm Heater(1),Tub(12), Fixer screw(5), Motor(2), Balance(9) 13mm Shock Absorber (2 holes each in left/right), Damper(2), Damper(friction 2) 19mm Pulley(1) Double-ended...

8 _ Disassembly and Reassembly 3-2. STANDARD DISASSEMBLY DRAWINGS ► This is a standard disassembly diagram and may differ from the actual product. Use this material as a reference when disassembling and reassembling the product.  Disassembly Part Figure Description Assy Cover Top 1. Remove 2 screws...

Disassembly and Reassembly _ 9  Reassembly Part Figure Description Assy Drawer 1. Fit the hole and press the Cap Rinse so that it can be assembled. 2. Make sure to fit the rail when reassembling the Assy drawer. 3. Put the drawer in the right direction.

10 _ Disassembly and Reassembly  Disassembly Part Figure Description Assy Drawer (Auto Dispense) 1. Pull to open the Drawer by hand. 2. While holding down the release lever inside the drawer (red box) , slide open the drawer. 3. Disassemble the Cover Drawer by hand. 4. Pull up the Cap Rinse to remo...

Disassembly and Reassembly _ 11  Reassembly Part Figure Description Assy Drawer (Auto Dispense) 1. Fit the hole and press the Cap Rinse so that it can be assembled. 2. Assemble the Cover Drawer by hand. 3. Make sure to fit the rail when reassembling the Assy drawer. 4. Place the drawer in the right...

12 _ Disassembly and Reassembly  Disassembly Part Figure Description Assy Panel Control (Simple) - Before you start, disassemble Assy Cover Top, Assy Drawer. 1. Remove 2 screws holding the drawer and panel using (+) screw driver. 2. Remove the screws at the top of the ASSY- PANEL CONTROL using (+) ...

Disassembly and Reassembly _ 13  Reassembly Part Figure Description Assy Panel Control (Simple) 1. Connect the terminal by hand. Take a look at the hook and put it in the right place. Be careful not to break the hook. Make sure the Wire harness are not getting stuck in other parts. 2. Assemble the ...

14 _ Disassembly and Reassembly  Disassembly Part Figure Description Assy Panel Control (LED) - Before you start, disassemble Assy Cover Top, Assy Drawer. 1. Remove 2 screws holding the drawer and panel using (+) screw driver. 2. Remove the screws at the top of the ASSY- PANEL CONTROL using (+) scr...

Disassembly and Reassembly _ 15  Reassembly Part Figure Description Assy Panel Control (LED) 1. Connect the terminal by hand. Take a look at the hook and put it in the right place. Make sure the Wire harness are not getting stuck in other parts. 2. Assemble the hook of housing drawer and aseemble s...

16 _ Disassembly and Reassembly  Disassembly Part Figure Description Assy Housing-Drawer Before you start, disassemble Assy Cover Top, Assy Panel Control.1. Remove 4 screws to disassemble frame plate- up using (+) screw driver. 2. Remove the Band-ring. (2ea) Be careful not to break the hose.

Disassembly and Reassembly _ 17 Part Figure Description Assy Housing-Drawer 3. Separate the water valve hose with long nose plier. 4. Separate Housing Drawer low by pressing the hooks on both sides by hand. To fully separate, disassemble Water Valve. Be careful not to break the hook.

18 _ Disassembly and Reassembly Part Figure Description Assy Housing Drawer (Auto Dispense) 1. Disassemble the 6 screws holding the pump with (+) screw driver. To fully separate, disassemble Water Valve. 2. Separate Housing Drawer low by pressing the hooks on both sides by hand. To fully separate, d...

Disassembly and Reassembly _ 19 Part Figure Description Assy Housing Drawer (Auto Dispense) 1. Assemble the Housing Drawer low by pressing the hooks on both sides by hand. 2. Assemble the 6 screws holding the pump with (+) screw driver.

20 _ Disassembly and Reassembly  Reassembly Part Figure Description Assy Housing-Drawer 1. Assemble the Housing Drawer low by pressing the hooks on both sides by hand. Be careful not to break the hose. 2. Assemble the water valve hose with long nose plier. Be careful not to break the hook. Make sur...

Disassembly and Reassembly _ 21 Part Figure Description Assy Housing-Drawer 3. Assemble the Band rings. (2ea) Make sure to insert the hoses and assemble the clamp, band rings correctly. There’re risks of leakage or poor performance when it’s misassembled. 4. Remove 4 screws to disassemble frame plat...

22 _ Disassembly and Reassembly  Disassembly Part Figure Description Frame Front Before you start, disassemble Assy Cover Top, Assy Panel Control. Be careful not to tear up the diaphragm. 1. Using long nose pliers, pick up one of the rings on Wire-Diaphragm which connect the spring and the wire end...

Disassembly and Reassembly _ 23 Part Figure Description Frame Front 6. Remove cover filter by hand. 7. Press the hook to remove Guide cover filter using (-) screw driver. Be careful not to break the hook. 8. Pull the Guide filter towards you. 9. Lift Frame front up to disassemble. Cover-Back Unfaste...

24 _ Disassembly and Reassembly  Disassembly Part Figure Description Assy Door Before you start, disassemble Assy Cover Top, Assy Panel Control and Frame Front. 1. Remove the wire by disassembling the 3 hooks using long nose plier. 2. Disassemble the terminal and remove the holders using long nose ...

Disassembly and Reassembly _ 25  Reassembly Part Figure Description Assy Door BACK SIDE FRONT SIDE 1. Put the terminal through the biggest hole and assemble 3 hooks as shown in the pictures. 2. Assemble the door with Frame Front by fitting the two hooks and assemble 2 screws holding the Assy door w...

26 _ Disassembly and Reassembly  Disassembly Part Figure Description Door-Lock S/W Before you start, disassemble Assy Cover Top and Assy Panel Control.1. Open the Door. Remove the Wire Diaphragm and remove the Frame Front. 2. Remove 2 screws with (+) screw driver. 3. Remove Cover Door Switch by gen...

Disassembly and Reassembly _ 27  Reassembly Part Figure Description Door-Lock S/W 1. Assemble the terminals. (2ea) Make sure the Wire harness are not getting stuck in other parts. 2. Assemble the Cover Door Switch by gently pushing the red box part with hand. Make sure the Wire harness are not gett...

28 _ Disassembly and Reassembly  Disassembly Part Figure Description Diaphragm Before you start, remove cover top, Assy Drawer, Assy Panel Control and Frame Front.1. Unfasten the screw with (+) screw driver on Joint Diaphragm and wire diaphragm. 2. Remove Joint Diaphragm by hand.3. Remove hose and ...

Disassembly and Reassembly _ 29  Reassembly Part Figure Description Diaphragm 1. Assemble the Diaphragm with tub by hand. Diaphragm and tub has triangle part make sure to fit them correctly. 2. Assemble hose and clamp with long nose plier, and fasten the screw with (+) screw driver. 3. Assemble Joi...

Wiring Diagram _ 35 5. WIRING DIAGRAM 5-1. WIRING DIAGRAM (SIMPLE) ► This Document can not be used without Samsung’s authorization. n REFERENCE INFORMATION BLK BLACK BLU BLUE GRN GREEN GRY GRAY NTR NATURAL ORG ORANGE PNK PINK RED RED SKYBLU SKYBLUE VIO VIOLET WHT WHITE YEL YELLOW

38 _ Reference 6. REFERENCE 6-1. WD6000T PROJECT NAME ► Door 10-Digit DOOR DESIGN DOOR COLOR DECO COLOR S Best Black D.silver B Better Black Black W Better Black White L Good Black D.silver H Good White D.silver A Basic Black Black T Basic White White C Old Basic Black - E Old Basic White - ► Region...