Samsung MIM-E03DN - Manuals

6 English At a Glanc e Buttons Overview 01 02 05 04 06 07 Outdoor 03/28/2019 1:30 PM Zone1 Zone2 30 Heat Set ° ° 28.2 .0 24 Heat Set ° .0 DHW 45 Economic Set ° .0 03 Remote Controller Overview At a Glance 01 Operation status display • Displays the operation/function settings and statuses. 02 Operati...

7 English At a Glanc e Home Screen Overview Outdoor 03/28/2019 1:30 PM Zone1 Zone2 30 Heat Set ° ° 28.2 .0 24 Heat Set ° .0 DHW 45 Economic Set ° .0 01 02 03 05 04 01 Outdoor temperature display • Displays outdoor temperature. 02 Date and time display • Displays current date and time. 03 Zone 1 disp...

8 Remote Controller Overview English At a Glanc e DHW Screen Overview Standard Set Current 84 ° ° .0 -2.4 03/28/2019 1:30 PM DHW 01 02 03 04 05 06 07 01 Set temperature display • Displays the set temperature. 02 Current temperature display • Displays current temperature for Water Outlet . 03 Operati...

9 English At a Glanc e Remote Controller Operation Operating basic mode Press the button to enter the Setting screen from the Home screen with the Zone 1 or Zone 2 activated. On each screen, press the and then press the or button to select any of Auto, Cool , and Heat modes. Auto mode Hydro unit wil...

11 English At a Glanc e Adjusting desired temperature On each screen, press the or button to adjust the temperature. NOTE • You can adjust the desired temperature by 0.1, 0.5, 1 °C. (Default 0.5°C) Setting the set temperature On each screen, press the or button to select a desired menu and then pres...

12 Power Smart Features English Po w er Smar t F eatur es There is a variety of useful functionality provided by the product. Power Smart Features Operation status Use this to display the operation status:COMP operation, Back up heater, Booster heater, Solar , Back up boiler, Water pump , Water tank...

13 English Ener gy -Saving Oper ation Setting schedule Press the button, press the , or , button to select Schedule , and then press the button. When you select Add a schedule, you can configure settings for Daily schedule, Weekly schedule , Yearly Schedule , and Holiday . Type Description Daily sch...

14 Energy-Saving Operation English Ener gy -Saving Oper ation Energy Press the button, press the , or , button to select Energy , and then press the button. You can see and set any of Energy Usage and Energy Setting . Classification Type Description Energy Usage - Displays the Instantaneous Power , ...

15 English Ener gy -Saving Oper ation TDM (Time-Division Multi) Variables (TDM product Only) Press the button, press the , or , button to select Priority A2A , and then press the button. Setting FSV #5033 to '0' becomes 'Priority A2A', and setting to '1' becomes 'Priority DHW'. • Under the installat...

16 Setting Options English Setting Options How to set the Options 1 Press the button. 2 Press the or button to select Option, and then press the button. 3 See the following pages to select the desired menu. Step 1 Step 2 Step 3 Step 4 Step 5 Description Default Button Lock ON/ OFF OFF Error List - -...

18 Setting Options English Setting Options Current Time Setting (Example) 1 Press the button. 2 Press the or button to select Option , and then press the button. 3 Press the or button to select User mode , and then press the button. 4 Press the or button to select Wired remote controller , and then ...

19 English Installation/S ervic e mode Additional functions of the Wired Remote Controller 1 If you want to use the various additional functions for your Wired Remote Controller, press the and buttons at the same time for more than 3 seconds. • The password entry screen appears. 2 Enter the password...

20 Installation/Service mode English Installation/S ervic e mode Installation/Service mode NOTE • Unavailable functions are marked inactive and they cannot be set. • If communication initialization is needed after the setting, the system will reset automatically and communication will be initialized...

26 Installation/Service mode English Installation/S ervic e mode How to upload or download field settings (example) 1 Insert an SD card into the Sub PBA SD Card slot on the Hydro unit. 2 Select Field Setting Value in the Service mode . 3 Press the or button to select FSV Upload/Download . NOTE • Upl...

27 English Field S etting Mode CAUTION • Set the FSV value of the product other than the specified models by referring to the FSV label provided with the manual of the product, and then attach it on the control box's cover. The FSV values in the table are applied to the specified models. NOTE • Be s...

28 Field setting mode English Field S etting Mode Remote Controller Setting Range: Code 10** Space Cooling • Target water outlet temperature : Upper limit(#1011, Default 25℃, Range : 18 ~ 25℃), Lower limit(#1012, Default 16℃, Range : 5 ~ 18℃) ‒ With this default FSV settings, user can change the tar...

30 Field setting mode English Field S etting Mode Water Law & Room Thermostat/ Wired remoted controller: Code 20** Ta #2021/2031 #2022/2032 #2061/2071 #2062/2072 #2011 #2012 #2051 #2052 1 1 2 2 at Floor/at FCU Cooling WL Ts : Target Temp.Ta : Ambient Temp. Heating WL Water Law for Heating • Outd...

32 Field setting mode English Field S etting Mode • When the Room thermostat is used, floor valve should be connected to 2 way valve #1 and the FCU valve should be separately connected to 2 way valve #2 of the Hydro Unit PBA. • When only floor cooling/heating is installed and if the Water Law or out...

35 English Field S etting Mode [DHW Tank water temperature thermo on/off control] T(C) T U > T HP MAX T HP MAX T HP OFF T HP ON T U #3021 #3022 #3023 T(C) T U < T HP MAX T HP MAX T U =T HP OFF T HP ON #3021 #3023 Tu : User set temp.T(C) : Temp. (Celsius) • DHW heating mode timer : Mode timer m...

36 Field setting mode English Field S etting Mode [Time variation control of Heat pump and booster heater of DHW] t 1 0 1 0 1 0 1 0 Booster Operation H/P Operation #3032 #3025 DHW request Heating request NOTE • The FSV #4022 for booster heater priority should be set to “0 (both)” or “2” (booster) to...

37 English Field S etting Mode <Example of using BSH in hot water supply> Case 1) When set temperature is 70℃ BSH is ON at less than 68 degrees, OFF at more than 70℃. Case 2) When setting temperature is 50℃ (FSV 3022 = 0 condition) Heat pump and BHS are ON at less than 45 degrees, OFF at more ...

38 Field setting mode English Field S etting Mode Disinfection Function 1) " Booster heater " Disinfection • The FSV #3041 should be set to "1 (On)" (Default) to use disinfection function. ‒ Scheduling : Day (#3042, Default "Friday"), starting time [#3043, Default "23:00&...

39 English Field S etting Mode 3) "R290 Heat Pump+ Booster heater " Disinfection • The FSV #3041 should be set to "1 (On)" (Default) to use disinfection function. • When FSV#3031 is set to "1 (On)", the disinfection function is performed by the heat pump to reach a target tan...

40 Field setting mode English Field S etting Mode NOTE • Disinfection function is available only when a booster heater is connected. (However, AE***CXY*** is also capable of Heat Pump Disinfection.) • R290 Mono Outdoor Unit (AE***CXYD*G) and Hydro Unit (AE***CNW***), Control Kit (MIM-E03DN) combinat...

42 Field setting mode English Field S etting Mode Additional heating option : 40** Heat Pump Variables for Space Heating • FSV #4011 for DHW priority is set to “0(DHW)” (Default) as a default. Space heating gets a priority by setting FSV #4011 “1”, but this is only valid when the outdoor temperature...

43 English Field S etting Mode Mixing vavle Installation (Field Option) • The FSV #4041 should be set to “1 or 2” to use mixing valve.※ 4041 =1 : Controlled based on the temperature difference (4042, 4043)※ 4041 =2 : Controlled based on the temperature difference of the WL value ex) Heating <#404...

44 Field setting mode English Field S etting Mode Field Setting Value (FSV) 50**/60** Code 50**/60** : User’s options for extra functions • The values in the following table are just examples for your understanding. Main Menu & Code Menu Function Sub Code MODEL CODE : AE200 (260)RNW***/ AE200(26...

47 English Field S etting Mode PV Control (Photovoltaics control) This is for energy saving by using the solar energy. The FSV #5081 should be set to “1(Yes)” for PV control. (However, Peak power control can not be used at the same time.) FSV 0 1 #5081 Disable (Default) Activation NOTE • Except for ...

48 Field setting mode English Field S etting Mode Smart Grid Control NOTE • MIM-E03DN (MONO Control Kit) model does not support this Smart grid function. The FSV #5091 should be set to “1(Yes)” for Smart Grid control. FSV 0 1 #5091 Disable (Default) Activation Operation mode for Smart Grid Operation...

49 English Appendix Maintenance activities • In order to ensure optimal availability of the unit, a number of checks and inspections on the unit and the field wiring have to be carried out at regular intervals, preferably yearly. This maintenance should be carried out by local technician. Besides ke...

51 English Appendix It the unit has some problem to work properly, error codes will be displayed on the wired remote controller. The following table describes the explanation of the error codes. Display Explanation Short- or open-circuit error of the room temperature sensor of the Zone 2 indoor unit...

52 Troubleshooting tips English Appendix Communication Display Explanation Communication error between remote controller and the Hydro unit Tracking error between remote controller and the Hydro unit Memory(EEPROM) Read/Write Error(Wired remote controller data error) E601, E604 E654 • MEMORY(EEPROM)...

53 English Appendix Water pump & Flow Sensor Display Explanation Low flow rate error • in case of low flow rate in 30 sec during water pump signals is ON(Starting) • in case of low flow rate in 15 sec during water pump signals is ON(After starting)Normal flow rate error • in case of normal flow ...

54 English Appendix Display Explanation Error Source 101 Hydro Unit / Outdoor Unit communication connection error Hydro Unit 120 Short- or open-circuit error of the room temperature sensor of the Zone 2 indoor unit (detected only when the room thermostat is used) Hydro Unit 121 Short- or open-circui...

57 English Appendix Memo DB68-09088A-06_IB_EHS Wired Remote-Control Kit OEM_EU_EN_.indd 57 2024-07-01 오후 5:28:10

Item Description Installation manual User manual O-Ring (2EA) ❋ Temp . sensor = Temperature sensor Optional Accessories Item(Model Name) Components Compatibility MIM-E03DN Backup Heater Kit MHC-300FP Sub Backup Heater (3 kW) O Main components Model name MIM-E03DN Detail components Parts Qty . Main P...

Installing the unit Installing the remote controller Dimension 120 120 19 (Unit : mm) 7 DB68-09089A-05_IM_EHS Control Kit OEM_EU_EN_.indd 7 DB68-09089A-05_IM_EHS Control Kit OEM_EU_EN_.indd 7 2024-07-01 오후 2:06:52 2024-07-01 오후 2:06:52

Installing the unit Wired Remote Controller Installation 1 . Insert the flat-head screwdriver into two square grooves at the bottom of the Wired Remote Controller and rotate it to lift the front cover for removal from the rear cover . 2 . Arrange the power cable and the communication cable so that t...

3 . Using two or more screws, firmly affix the rear cover of the remote controller to the wall, and then cut off the grooves of the front covers for communication and power cables, making sure these cables have reasonable length . 10 mm or more 10 mm or more 50 mm or more 10 mm or more Screw hole Re...

Installing the unit 6 . Remove the front protective film . • When installing a Wired Remote Controller by using a cable longer than 10 m, you must install the communication cable and the power cable separately . (Electrical interference can cause the Wired Remote Controller to malfunction .) • When ...

Wiring works • Field-supplied electrical components such as power switch, circuit breakers, wires, terminal blocks, etc must be properly chosen with compliance with national legislation or regulation . • Switch off the power supply before making any connections .• All field wiring and components mus...

Wiring works Selection for the power and booster heater wire terminal f Connect the cables to the terminal board using the solderless ring terminal . f Use certified and verified cables . f Connect using a driver which is able to apply the rated torque to the screws . f If the terminal is loose, fir...

* Be sure to connect the ring terminal between the cable and terminal block . f ELCB M5 Screw [Terminal Block on PBA] 9 .8 mm 8 .5 mm TB-A,TB-A1 TB-B(26PIN) [ELCB] 10 .6 mm Selecting solderless ring terminal f Select a solderless ring terminal of a connecting power cable based on a nominal dimension...

Wiring works How to connect your extended power cables 1 . Prepare the following tools . Tools Crimping pliers Connection sleeve (mm) Insulation tape Contraction tube (mm) Spec MH-14 20xØ6 .5(HxOD) Width 19mm 70xØ8 .0(LxOD) Shape 2 . As shown in the figure, peel off the shields from the rubber and w...

5 . Apply heat to the contraction tube to contract it . f Method 1 Contraction tube f Method 2 Contraction tube 6 . Wrap it with the insulation tape twice or more and position your contraction tube in the middle of the insulation tape . f Method 1 40 mm Insulation tape f Method 2 35 mm Insulation ta...

Wiring works Grounding work f Grounding must be done by a qualified installer for your safety . Grounding the power cable f The standard of grounding may vary according to the rated voltage and installation place of a heating pump . f Ground the power cable according to the following . Installation ...

Power and communication with outdoor unit Power Wire ELCB Communication Wire N L • Be careful when connecting L, N . CAUTION Connecting the power wire 1 . Connect ‘Live’ and 'Neutral’ power line with ‘L, N’ of a ELCB .2 . Connect ‘L,N’ of a ELCB with ‘A1 and A2’ in TB-A . 3 . Connect ‘Protective Ear...

Wiring works Connecting the communication wire f Connect ‘outdoor unit’s F1&F2’ with ‘control kit’s F1&F2 in TB-C’ by 2 core cable . Outdoor Unit (at Control Plate) Control Kit Communication with a wired remote controller (1 unit) Wired Remote Controller (Main) Communication with a wired rem...

Connecting a wired remote controller 1 . Connect 'F3, F4' of TB-C kit with 'F3, F4' of a wired remote controller . f 2 units (wired remote controllers) are able to be installed on TB-C . f When 2 units are installed, either one shall has "Main" setting and another one shall have "Sub"...

Wiring works Connecting a PV(Photovoltaic) Signal / Peak power control Signal 1 . Install as above diagram .2 . Connect the PV / Peak power control signal wire to the 'CNS046' connector . • It operates according to the setting of FSV, and both functions can not be used at the same time . (PV Control...

Backup boiler Connection of the back-up boiler Description No. of wires Min. / Max. current Thickness Supply Scope Back-up Boiler 2+ground 10mA / 50mA 0 .75mm 2 H05RN-F or H07RN-F Field supply (220-240V~, Input) L N L N When it set back up boiler on the control kit (relay off ) Boiler B4 : Back-up b...

Wiring works Connection guide of additional pump Case 1) INV. pump Connect the PWM control external type pump to PWM terminal block and power cable to the external contact terminal .The maximum number of additional pump installation is one inverter pumps (Input power 100W) .1 . Power supply (For add...

Wiring works Connection of the 2-way valve Description No. of wires Min. / Max. current Thickness Supply Scope Motorized 2-way valve to shut off UFH loops during cooling . 2+ground 10mA / 50mA > 0 .75 mm 2 , H05RN-F or H07RH-F Field supply (220-240V~, Output) N L2 N L1 * Connection of 2 wires 2-w...

Wiring works Example zone#1 only : cooling mode zone#2 only : cooling mode zone#1, zone#2 : cooling mode Room thermostat N L Room thermostat N L Room thermostat N L zone#1 only : heating mode zone#2 only : heating mode zone#1, zone#2 : heating mode Room thermostat N L Room thermostat N L Room thermo...

Example of RX1 (Danfoss) f In manual of a RF receiver RX1 and RX2 N L 1 2 3 4 Terminal 1 RX2 only Electronics Zone 2 on Zone 1 on Zone 1 off Com f Example of wiring works N L 1 2 3 4 19 20 21 22 23 24 Control kit RF receiver (RX1) Cool (zone#1) Cool (zone#2) Heat (zone#1) Com Heat (zone#2) 31 DB68-0...

Wiring schematics Wiring diagram USE COPPER SUPPLY WIRES. UTILISER DES FILS D'ALIMENTATION EN CUIVRE. EARTH YEL/GRN CNP101  (WHT) 6 3 5 7 9 111315 1719 1 2 21 CN81 (RED) 2 4 8 1012 14 18 20 23 3 4  COMP CHECK 16 22 24 1 CNS051  (WHT) 2 ERROR CHECK 1  EXT CTRL  CN83  (RED) 1  DC FAN 2 CNS808   (YEL) ...

Self-test mode of wired remote controller Use of self-test mode 0 Please enter your PASSWORD Service mode Service mode Reset All Service Mode Power Master Reset ODU K3 Reset Field Setting Value Self-Test Mode Indoor Unit Option 1 . If you want to use the various additional functions for your Wired R...

DHW tank Electrical connections Procedure • Switch off the power supply before making any connections .• Use a thermal grease in thermistor pocket after installing electric connections . WARNING Connections to be made in the electrical box of DHW tank 1 . Connect the booster heater power supply and ...

Booster heater Booster heater Recommended wire specification Load Power Supply Power Cable Max. Length mm 2 , wires m Use Booster Heater (Max. 3kW) 1Ø, 220-240V, 50Hz 4 .0 / 3 L < 10m 6 .0 / 3 10m < L ❈ Code designation IEC: 60245 IEC 57/ CENELEC: H05RN-F Connecting a booster heater (PTC heate...

DHW tank DHW tank Switch box layout DHW Tank Temp . (2 .1m) CNS042(YEL) ❋ Use a correct sensor pocket which is fit for the DHW tank sensor(OD Ø6) . If the gap between the supplied sensor and DHW tank sensor pocket is big, use thermal grease . • When you set the hot water supply temperature to 55°C o...

Troubleshooting IMPORTANT: All maintenance or repair work must be executed by an approved installer . Problem Possible cause Solution Hot water is not coming out . No power supply to the water heater Check if there is any power on the power supply terminal on the thermostat . The thermostat may be s...

Mixing Valve Installation of mixing valve Under Floor Radiator TW4 Balancing Vessel (Mixing tank) When two different zones are used with different temperature, adjust the temperature of discharge water to high temperature water and control the amount of bypass to provide low temperature water by app...

ex) Heating <#4041=1> <#4041=2> Tw2 Water Temp . Outdoor Ambient Temp . Ta TW3 #4042 TW4 Tw2 Water Temp . Outdoor Ambient Temp . Ta TW3 TW4 ❋ The mixing valve is controlled based on the FCU WL value . ❋ As the #4044 value increases and the #4045 value decreases, the control speed increas...

Concrete curing function When pipes of floor heating are installed, operation for reinforcing concrete curing is applied . (Period of operation: 23 days) Entering procedure 1 . After turning off the DIP switch K3 (3rd switch of SW03) of control kit (Default ON), turn off and turn on the control kit ...

Concrete curing function NOTE • Definition of Dip switch function Dip S/W S/W #1 S/W #2 S/W #3 S/W #4 ON (default) • None • None • None • Turn off when an E101 error occurs OFF • Emergency heating • Emergency hot water supply • Concrete curing • E101 error does not turn off reference item • Please r...

Installation option setting f Set the control kit installation option with remote controller option . The procedure of option setting High Temp Button High Fan Button Mode change Low Temp Button Low Fan Button Entering mode for option setting Option setting mode Entering mode to set option 1 . Remov...

Installation option setting Changing a particular option You can change each digit of set option . Option SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 Explanation PAGE MODE The option mode you want to change The tens’ digit of an option SEG you will change The unit digit of an option SEG you will change The change...

Troubleshooting If the unit has some problem to work properly, some error codes will be displayed on the controller .The following table described the explanation of error codes on the LCD display . Thermistor f Check its resistance . 10kohm@25 °C (Control kit), 200kohm@25 °C (DHW Tank, Solar) f Che...

Troubleshooting Communication Display Explanation Communication error between remote controller and the Control kit Tracking error between remote controller and the Control kit Memory(EEPROM) Read/Write Error(Wired remote Controller data error) E601, E604 E654 MEMORY(EEPROM) Read/Write Error (Wired ...

Water pump & Flow Sensor Display Explanation Low flow rate error• in case of low flow rate in 30 sec during water pump signals is ON(Starting)• in case of low flow rate in 15 sec during water pump signals is ON(After starting)Normal flow rate error• in case of normal flow rate in 10min during wa...

Error codes If the unit has some problems and does not work normally, error code is shown on the OUTDOOR UNIT main PBA or LCD of the wired remote controller . Display Explanation Error Source 101 CONTROL KIT / OUTDOOR UNIT wire connection error CONTROL KIT, OUTDOOR UNIT 120 Short- or open-circuit er...

Memo 50 DB68-09089A-05_IM_EHS Control Kit OEM_EU_EN_.indd 50 DB68-09089A-05_IM_EHS Control Kit OEM_EU_EN_.indd 50 2024-07-01 오후 2:07:08 2024-07-01 오후 2:07:08

This appliance is filled with R-32. DB68-09089A-05 DB68-09089A-05_IM_EHS Control Kit OEM_EU_EN_.indd 52 DB68-09089A-05_IM_EHS Control Kit OEM_EU_EN_.indd 52 2024-07-01 오후 2:07:08 2024-07-01 오후 2:07:08