Samsung MIM-E03AN - Manuals

Samsung MIM-E03AN Air Conditioner – User Manual, Installation Manual in PDF format online.

Manuals:

User Manual
Installation Manual

User Manual Samsung MIM-E03AN

Installation Manual Samsung MIM-E03AN

Summary

Page 2 - Contents

Contents Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Product specifications . . . . . . . . . . . . . . . . . . . . . ...

Page 3 - Safety precautions; WARNING; components inside the unit .; Warning; Do not place containers with liquids or other objects on the unit .; ENGLISH

Safety precautions Carefully follow the precautions listed as below because they are essential to guarantee the safety of SAMSUNG product . WARNING • Always disconnect a power supply of Air-Water Heat Pump before servicing it or accessing components inside the unit . • Verify that installation and t...

Page 4 - Product specifications; Item

Product specifications Item Description MIM-E03 ✴ N Wired remote controller Temp . Sensor Temp . Sensor for DHW Tank (15m, YEL) (1EA) Temp . Sensor for Mixing Valve (15m, BLU) (1EA) Temp . Sensor for Heater (15m, BLK) (1EA) Smart Grid cable (Red, 2 m, 1EA) Flow Switch (1EA, 2m) Sensor holder (2EA, O...

Page 5 - Main components; Model name; Mounting the unit; Procedure

Main components Model name MIM-E03 ✴ N Detail components Parts Qty . Main PBA 1 ELCB- Rated current : 30A - Leakage current : 30mA 1 Grounding screw 8 Rubber 4 Base plate 1 Top cover plate 1 Case screw 2 Weight (Net) 3 .5 kg Packing size (W x H x D) 329 mm x 439 mm x 168 mm ❋ ❋ Flow Switch Set Point...

Page 6 - Installing the unit; Installing the remote controller; Dimension

Installing the unit Installing the remote controller Dimension 120 124 63 .8 19 .5 (Unit : mm) 6 EHS MONO Kit-EU_IM_05388A-04_EN.indd 6 2016-06-23 오후 3:42:56

Page 7 - Installation; separate it from the rear cover .; to disassemble it easily .

Installation 1 . Push the two hooks at the bottom of your Wired Remote Controller at the same time, and then pull up the front cover to separate it from the rear cover . ❋ ❋ Push the two hooks at the same time . NOTE • Insert a flat head screwdriver into the square groove in the upper area of the ho...

Page 8 - . Reassemble your wired remote controller .; with a proper thickness .; Maximum distance of communication cable : 100 m

Installing the unit 3 . Using more than two screws, firmly affix the rear cover of the remote controller to the wall, and then connect communication cables(F3, F4), making sure these cables have reasonable length, to the terminal at the back of the cover . 10 mm or more 10 mm or more 50 mm or more 1...

Page 9 - Wiring works; Incomplete earth may cause electrical problems .; Layout of PCB; Note

Wiring works • Field-supplied electrical components such as power switch, circuit breakers, wires, terminal blocks, etc must be properly chosen with compliance with national legislation or regulation . • Switch off the power supply before making any connections .• All field wiring and components mus...

Page 11 - Selecting solderless ring terminal

Selecting solderless ring terminal f f Select a solderless ring terminal of a connecting power cable based on a nominal dimensions for cable . f f Cover a solderless ring terminal and a connector part of the power cable and then connect it . Silver solder Nominal dimensions for cable (mm2) 1.5 2.5 4...

Page 12 - How to connect your extended power cables; Tools; Spec; Push the core wire into the sleeve from both sides .; Method 2; Twist the wire cores together and push it into the sleeve .; Method 1

Wiring works How to connect your extended power cables 1 . Prepare the following tools . Tools Crimping pliers Connection sleeve (mm) Insulation tape Contraction tube (mm) Spec MH-14 20xØ6 .5(HxOD) Width 19mm 70xØ8 .0(LxOD) Shape 2 . As shown in the figure, peel off the shields from the rubber and w...

Page 13 - Three or more layers of insulation are required .; . Apply heat to the contraction tube to contract it .; - Incomplete wire connections can cause electric shock or a fire .

5 . Wrap it with the insulation tape twice or more and position your contraction tube in the middle of the insulation tape . Three or more layers of insulation are required . f f Method 1 40 mm Insulation tape f f Method 2 Insulation tape 35 mm 6 . Apply heat to the contraction tube to contract it ....

Page 14 - Selection for the power and booster heater wire terminal; Use certified and verified cables .; ELCB

Wiring works Selection for the power and booster heater wire terminal f f Connect the cables to the terminal board using the solderless ring terminal . f f Use certified and verified cables . f f Connect using a driver which is able to apply the rated torque to the screws . f f If the terminal is lo...

Page 15 - Grounding work; Grounding must be done by a qualified installer for your safety .; Grounding the power cable; Ground the power cable according to the following .; Note 1) Grounding work 3

Grounding work f f Grounding must be done by a qualified installer for your safety . Grounding the power cable f f The standard of grounding may vary according to the rated voltage and installation place of a heating pump . f f Ground the power cable according to the following . Installation place P...

Page 16 - Power and communication with outdoor unit; Connecting the power wire; Load

Wiring works Power and communication with outdoor unit Power Wire ELCB Communication Wire N L • Be careful when connecting L, N . CAUTION Connecting the power wire 1 . Connect ‘Live’ and 'Neutral’ power line with ‘L, N’ of a ELCB .2 . Connect ‘L,N’ of a ELCB with ‘A1 and A2’ in TB-A . 3 . Connect ‘P...

Page 17 - Connecting the communication wire; Communication with a wired remote controller (1 unit); Communication with a wired remote controller (2 units); Connecting a wired remote controller

Connecting the communication wire f f Connect ‘outdoor unit’s F1&F2’ with ‘control kit’s F1&F2 in TB-C’ by 2 core cable . Outdoor Unit (at Control Plate) Control Kit Communication with a wired remote controller (1 unit) Wired Remote Controller (Master) Communication with a wired remote contr...

Page 18 - Connecting a temp. sensor wire into DHW

Wiring works Temp. Sensor for DHW, Backup heater and a water Flow S/W Relay External wiring to control a switch of relay by a installer Temp . sensor for DHW Flow s/w Temp . sensor for backup heater Connecting a temp. sensor wire into DHW 1 . Put the sensor side of a temp . sensor wire into the desi...

Page 19 - DHW tank Switch box layout

DHW tank Switch box layout DHW Tank Temp . (15m) CNS042(YEL) ❋ ❋ Use a correct sensor pocket which is fit for the DHW tank sensor(OD Ø6) . If the gap between the supplied sensor and DHW tank sensor pocket is big, use thermal grease . 19 ENGLISH EHS MONO Kit-EU_IM_05388A-04_EN.indd 19 2016-06-23 오후 3...

Page 20 - DHW tank; Electrical connections; Connections to be made in the electrical box of DHW tank; Connection of the solar circulation pump for DHW tank; Description; block as shown on the diagram .

DHW tank Electrical connections Procedure • Switch off the power supply before making any connections .• Use a thermal grease in thermistor pocket after installing electric connections . WARNING Connections to be made in the electrical box of DHW tank 1 . Connect the booster heater power supply and ...

Page 21 - Power connection; • The booster heater that will be connected should be 3 kW or lower .; Troubleshooting

Connection of the solar circulation pump / DHW Thermostat for DHW tank Description No. of wires Max. A Thickness Supply Scope Solar pump / DHW Thermostat 2+ground 10 mA 0 .75mm 2 H05RN-F or H07RN-F Field supply (230 V~, Input) SOLAR PUMP / DHW Thermostat (L) SOLAR PUMP / DHW Thermostat (N) Controlle...

Page 22 - parts of the same specification .; screw is properly fitted .

Problem Possible cause Solution Heating is not working Heating element or internal electrical wiring is out of order . Check if there is any power on the power supply on the connector of the heating element between black and yellow/green wires . If this is OK, press the reset button on the fuse/safe...

Page 23 - Recommended wire specification; . Directly connect a ‘Booster heater’ with ‘A3 and A4 ’ in TB-A .; Specification table

Booster heater Booster heater Recommended wire specification Load Power Supply Power Cable Max. Length mm 2 , wires m Use Booster Heater (Max. 3kW) 1Ø, 220-240V, 50Hz 4 .0 / 3 L < 10m 6 .0 / 3 10m < L ❈ Code designation IEC: 60245 IEC 57/ CENELEC: H05RN-F Connecting a booster heater (PTC heate...

Page 24 - Backup heater; st step

Wiring works Backup heater Relay or Magnetic Contactor Wire Connecting a relay or a magnetic contactor for a backup heater (Not Directly connect a backup heater) 1 . Connect a "relay or a magnetic contactor" with "CNP003,CNP001,CNP002" . f f When a backup heater mode is "ON" ...

Page 25 - Backup boiler

Specification table Part Specification Tab-Terminal (output) Step1 : CNP003, CNP001Step2 : CNP003, CNP002 Connection load Relay or Magnetic contactor for a control signal Output(CNP003,CNP001 or (CNP003,CNP001)+(CNP003,CNP002) AC 230V (MAX 0 .5A) Backup boiler Connection of the back-up boiler Descri...

Page 26 - Connection guide of additional pump

Wiring works Connection guide of additional pump Case 1) INV. pump Connect the PWM control external type pump to PWM terminal block and power cable to the external contact terminal .The maximum number of additional pump installation is one inverter pumps (Input power 100W) .1 . Power supply (INV . P...

Page 27 - PWM characteristic curve

Case 2) AC pump The maximum number of additional pump installation is one AC pumps (Input power 100W) .1 . Power supply (AC Pump) Live additional pumpNeutral additional pump B7 B8 LN M/C PCB Terminal block Neutral additional pump Live additional pump B7 B8 Pump Power • Terminal of this product is fo...

Page 28 - Connection of the 2-way valve; -way motorized valve

Wiring works Connection of the 2-way valve Description No. of wires Max. A Thickness Supply Scope Motorized 2-way valve to shut off UFH loops during cooling . 2+ground 22 mA > 0 .75 mm 2 , H05RN-F or H07RH-F Field supply (230 V~, Output) N L1 N L2 * Connection of 2 wires 2-way valve In case of no...

Page 30 - Example; Target zone

Wiring works Example zone#1 only : cooling mode zone#2 only : cooling mode zone#1, zone#2 : cooling mode Room thermostat N L Room thermostat N L Room thermostat N L zone#1 only : heating mode zone#2 only : heating mode zone#1, zone#2 : heating mode Room thermostat N L Room thermostat N L Room thermo...

Page 31 - Control kit

Example of RX1 (Danfoss) f f In manual of a RF receiver RX1 and RX2 N L 1 2 3 4 Terminal 1 RX2 only Electronics Zone 2 on Zone 1 on Zone 1 off Com f f Example of wiring works N L 1 2 3 4 19 20 21 22 23 24 Control kit RF receiver (RX1) Cool (zone#1) Cool (zone#2) Heat (zone#1) Com Heat (zone#2) 31 EN...

Page 33 - Wiring schematics; Wiring diagram

Wiring schematics Wiring diagram 33 ENGLISH EHS MONO Kit-EU_IM_05388A-04_EN.indd 33 2016-06-23 오후 3:43:06

Page 34 - Self-test mode of wired remote controller; Use of self-test mode; and

Self-test mode of wired remote controller Use of self-test mode 1 . When using the self-test mode of the wired remote controller, press the [＜] and [＞] buttons for more than 3 seconds . 2 . You can operate the self-test mode as follows . f f Load list: When pressing the corresponding button, you can...

Page 35 - Delete

f f Thermostat 1, 2, and solar heat panel are displayed as below when you set them with an control kit . Thermostat 1 (Zone 1), Thermostat 2 (Zone 2), Solar heat panel (ON/OFF) f f Timer button: Whenever you press the button, the sensor value will be displayed in order . TW1(In)sensor TW2(Out1) sens...

Page 36 - Thermistor; Check its location as shown at the diagram .

Troubleshooting If the unit has some problem to work properly, some error codes will be displayed on the controller .The following table described the explanation of error codes on the LCD display . Thermistor f f Check its resistance . 10kohm@25 °C (Control kit), 200kohm@25 °C (DHW Tank, Solar) f f...

Page 37 - Communication; Display

Communication Display Explanation Communication error between remote controller and the Control kit Tracking error between remote controller and the Control kit Memory(EEPROM) Read/Write Error(Wired remote Controller data error) E601, E604 E654 MEMORY(EEPROM) Read/Write Error (Wired controller data ...

Page 39 - Error codes

Error codes If the unit has some problems and does not work normally, error code is shown on the OUTDOOR UNIT main PBA or LCD of the wired remote controller . Display Explanation Error Source 101 CONTROL KIT / OUTDOOR UNIT wire connection error CONTROL KIT, OUTDOOR UNIT 162 EEPROM Error CONTROL KIT ...

Page 41 - Mixing Valve; Installation of mixing valve

Mixing Valve Installation of mixing valve Under Floor Radiator TW4 Balancing Vessel (Mixing tank) When two different zones are used with different temperature, adjust the temperature of discharge water to high temperature water and control the amount of bypass to provide low temperature water by app...

Page 42 - The mixing valve is controlled based on the FCU WL value .; Connection of the mixing valve

Mixing Valve ex) Heating <#4041=1> <#4041=2> Tw2 Ta FCU WL #4042 Floor temp Tw2 Ta FCU WL Floor WL ❋ ❋ The mixing valve is controlled based on the FCU WL value . ❋ ❋ As the #4044 value increases and the #4045 value decreases, the control speed increases . (Temperature hunting may occur i...

Page 44 - Concrete curing function; Entering procedure; If an error is displayed, concrete curing function does not work .

Concrete curing function When pipes of floor heating are installed, operation for reinforcing concrete curing is applied . (Period of operation: 23 days) Entering procedure 1 . After turning off the DIP switch K3 (3rd switch of SW03) of control kit (Default ON), turn off and turn on the control kit ...

Page 45 - Installation option setting; The procedure of option setting; Entering mode for option setting

Installation option setting f f Set the control kit installation option with remote controller option . The procedure of option setting High Temp Button High Fan Button Mode change Low Temp Button Low Fan Button Entering mode for option setting Option setting mode 45 ENGLISH EHS MONO Kit-EU_IM_05388...

Page 46 - Entering mode to set option; . Remove batteries from the remote controller .; Changing a particular option; You can change each digit of set option .; 2 Series installation option

Installation option setting Entering mode to set option 1 . Remove batteries from the remote controller . 2 . Insert batteries and enter the option setting mode while pressing High Temp button and Low Temp button . 3 . Check if you have entered the option setting status . Changing a particular optio...

Page 47 - ECODESIGN REQUIREMENTS FOR SPACE HEATER

47 ENGLISH COMMISSION REGULATION (EU) No 813/2013 I) ECODESIGN REQUIREMENTS FOR SPACE HEATER II) A Model(s) : AE050JXYDEH B Air-to-water heat pump : yes C Water-to-water heat pump : no D Brine-to-water heat pump : no E Low-temperature heat pump : no F Equipped with a supplementary heater : no G Heat...

Page 68 - PRODUCT FICHE (ENERGY LABELLING OF SPACE HEATERS)

68 COMMISSION DELEGATED REGULATION (EU) No 811/2013 i) PRODUCT FICHE (ENERGY LABELLING OF SPACE HEATERS) ii) a Supplier's name or trademark Samsung Electronics Co., Ltd. Samsung Electronics Co., Ltd. Samsung Electronics Co., Ltd. Samsung Electronics Co., Ltd. b Supplier's model identifier AE090JXYDE...

Page 69 - PRODUCT FICHE (ENERGY LABELLING OF PACKAGES OF SPACE HEATER)

69 ENGLISH PRODUCT FICHE (ENERGY LABELLING OF PACKAGES OF SPACE HEATER) iii) a Supplier's name or trademark Samsung Electronics Co., Ltd. Samsung Electronics Co., Ltd. Samsung Electronics Co., Ltd. Samsung Electronics Co., Ltd. b Supplier's model identifier AE090JXYDEH AE090JXYDGH AE120JXYDEH AE120J...