Samsung AM022NN1PEH - Manuals

5 English Safet y Informat ion When installing the outdoor unit, make sure to connect the drain hose so that draining is performed correctly. • The water generated during the heating operation in the outdoor unit may overflow and result in property damage. In particular, in winter, if a block of ice...

6 English Safety Information Safety Information Safet y Informat ion In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate immediately without touching the power line. Do not touch the appliance or power line. • Do not use a ventilating fan. • A spark may result in an explosion o...

9 English Safet y Informat ion For use in Europe: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the applianc...

10 English Indoor Unit Overview At a Glanc e Indoor Unit Overview At a Glance Main parts The indoor unit and its display may look slightly different from the illustration shown below, depending on the model and the panel type. PC1*WFMAN / PC1*WCMAN 02 01 04 05 03 01 Display 02 Remote control sensor ...

11 English At a Glanc e PC1NUSMAN/PC1NUPMAN/PC1MWSKAN/PC1NWSMAN/PC1BWSMAN 02 03 04 01 01 Display 02 Air flow blade 03 Panel 04 Air intake Indication Function Remote control sensorOperation indicator • Heating and cooling model: Operation(Blue) / Defrost(Yellow) • Cooling only model: Operation indica...

12 English Operation Features At a Glanc e Operation Features Operating temperature and humidity When using the air conditioner follow the operating temperature and humidity ranges. Mode Outdoor temperature Indoor temperature Indoor humidity Cool mode Depending on the outdoor unit specifications 18°...

13 English Cl eaning and Maint enanc e Cleaning and Maintaining Cleaning the indoor unit exterior Wipe the surface of the indoor unit with a tepid damp cloth.Remove the dust accumulated in the narrow gaps of the product with a soft brush. CAUTION • Do not use alkaline detergent, sulphuric acid, hydr...

14 English Cleaning and Maintaining Cleaning and Maintaining Cl eaning and Maint enanc e Cleaning the air filter CAUTION • Before cleaning the indoor unit, be sure to turn off the auxiliary power switch. • Be sure to hold the grille with a hand to prevent dropping from the opening of the front grill...

18 English Cleaning and Maintaining Cleaning and Maintaining Cl eaning and Maint enanc e Periodical maintenance Unit Maintenance item Interval Requires qualified technicians Indoor unit Clean the air filter. At least once a month Clean the condensate drain pan. Once a year Required Clean the heat ex...

19 English Cl eaning and Maint enanc e Troubleshooting Refer to the following chart if the air conditioner operates abnormally. This may save time and unnecessary expense. Problem Solution The air conditioner does not operate immediately after it has been restarted. • Because of the protective mecha...

20 English Cleaning and Maintaining Cleaning and Maintaining Cl eaning and Maint enanc e Problem Solution The wired remote control does not operate. • Check whether the indicator is displayed at the bottom right of the remote control display. In this case, turn off both the air conditioner and the a...

21 English Cl eaning and Maint enanc e Problem Solution The air is not cool or warm enough. • Close the windows and doors to maximize the cooling and heating efficiencies. • If the Cool mode is stopped and then started immediately, cool air comes out after about 3 minutes to protect the compressor o...

22 English Technical specifications Cl eaning and Maint enanc e Type Model New weight Net dimension(W x D x H) Indoor unit AM017NN1PEH 8.0 kg 740 mm x 360 mm x 135 mm AM022NN1PEH 8.0 kg 740 mm x 360 mm x 135 mm AM022NN1DEH 10.0 kg 970 mm x 410 mm x 135 mm AM028NN1DEH 10.0 kg 970 mm x 410 mm x 135 mm...

23 English Instal lation Pr oc edure Step 1 Installing the indoor unit When deciding on the location of the air conditioner the following restrictions must be taken into account. 1 Place the pattern sheet on the ceiling at the spot where you want to install the indoor unit. NOTE • Since the diagram ...

24 English Installation Procedure Instal lation Pr oc edure 7 Adjust the unit to the appropriate position, taking into account the installation area for the front panel. • Place the pattern sheet on the indoor unit. • Adjust the space between the ceiling and the indoor unit by using a dimension gaug...

28 English Installation Procedure Instal lation Pr oc edure Step 4 Connecting the power and communication cables Power and communication cable connection • Before wiring work, you must turn off all power source. • Connect the power and communication cable among the units within maximum length to set...

29 English Instal lation Pr oc edure Selecting the crimping terminal lug 1 Select the crimping terminal lug based on the norminal dimension of the power cable. 2 Cover the connection part of the power cable and crimping terminal lug to insulate it. Silver solder F E L D d1 B d2 t B 2 R Norminal dime...

30 English Installation Procedure Instal lation Pr oc edure Specifications of the terminal blocks (Unit: mm) AC power: M4 screw Communication: M3.5 screw 11 13 7.5 9.0 18 13 .8 Power supply (single phase) MCCB ELB Min : 198V Max : 242V XA XA, 30 mA 0.1 s Power cable Earth cable Communication cable 2...

31 English Instal lation Pr oc edure Step 5 Setting the indoor unit addresses and the installation options You cannot set both of the indoor unit addresses and the installation options in a batch: set both of them respectively. Common steps for setting the addresses and options Low Temp button High ...

37 English Instal lation Pr oc edure Option SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 Function Page - Setting RMC address - Group channel (x16) Group address Indication and details Indication Details - Indication Details - Indication Details Indication Details 1 0 No RMC address RMC1 0 to F RMC2 0 to F 1 RMC...

47 English Instal lation Pr oc edure Changing the addresses and options individually When you want to change the value of a specific option, refer to the following table and follow the steps in Common steps for setting the addresses and options on page 31 . Option SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 Funct...

48 English Installation Procedure Instal lation Pr oc edure Setting up the ETO Communication between indoor and outdoor units (F1 and F2) Error output port (1, 2) Contact input port (5, 6) Main indoor unit Sub indoor unit External contact interface module MIM-B14 Main indoor unit 1 Disable the exter...

COUNTRY CALL OR VISIT US ONLINE AT UK 0333 000 0333 www.samsung.com/uk/support IRELAND (EIRE) 0818 717100 www.samsung.com/ie/support GERMANY 06196 77 555 77 www.samsung.com/de/support FRANCE 01 48 63 00 00 www.samsung.com/fr/support SPAIN 91 175 00 15 www.samsung.com/es/support PORTUGAL 210 608 098 ...

5 English Installation Pr oc edur e Installation Procedure Step 1 Checking and preparing accessories The following accessories are supplied with the indoor unit. The type and quantity may differ, depending on the specifications. Installation template Dimension gauge Insulation drain Flexible hose Ru...

6 Installation Procedure English Installation Pr oc edur e Indoor unit dimensions Slim 1way cassette (Small) (Unit: mm) 67 14 5 10 7 430 A B 123 36 130 80 420 960 792 (Space of suspension bolts) 860 (Ceiling opening dimension) Ceiling Outlet 235 (Spac e of suspension bolts) 380 (C eil ing opening di...

9 English Installation Pr oc edur e Spacing requirements 150 or more 1500 or more (Unit: mm) 150 or more 150 or more CAUTION ࡛ The indoor unit must be installed according to the specified distances in order to permit accessibility from each side, to guarantee correct operation, maintenance, and repa...

10 Installation Procedure English Installation Pr oc edur e 3 Install the suspension bolts, depending on the ceiling type. Ceiling support CAUTION ࡛ Make sure that the ceiling is strong enough to support the weight of the indoor unit. Before hanging the unit, test the strength of each attached suspe...

11 English Installation Pr oc edur e Step 5 Purging inert gas from the indoor unit The indoor unit comes with nitrogen gas (inert gas) charged at the factory. Therefore, all inert gas must be purged before connecting the assembly piping. Unscrew the pinch pipe at the end of each refrigerant pipe. Li...

12 Installation Procedure English Installation Pr oc edur e Step 7 Connecting the assembly pipes to the refrigerant pipes There are two refrigerant pipes of different diameters : ࡛ A smaller one for the liquid refrigerant. ࡛ A larger one for the gas refrigerant. The inside of copper pipe must be cle...

13 English Installation Pr oc edur e Step 8 Performing the gas leak test To identify potential gas leaks on the indoor unit, inspect the connection area of each refrigerant pipe using a leak detector for R-410A.Before recreating the vacuum and recirculating the refrigerant gas, pressurize the whole ...

14 Installation Procedure English Installation Pr oc edur e 5 Select the insulation of the refrigerant pipe. ࡛ Insulate the gas side and liquid side pipe, noting the insulation thickness that must differ according to the pipe size. ࡛ Standard: Less than an indoor temperature of 30°C, with humidity a...

15 English Installation Pr oc edur e Step 10 Installing the drain hose and drain pipe 1 Fix the flexible hose to the drain pipe. ࡛ The connection port of the flexible hose and PVC drain pipe must be fixed with PVC adhesives. Check out that the connected part doesn’t leak. Drain hose PVC Tube Joint +...

16 Installation Procedure English Installation Pr oc edur e ࡛ Do not apply force to the piping on the unit side when connecting the drain hose. The hose should not be allowed to hang loose from its connection to the unit. Fasten the hose to a wall, frame or other support as close to the unit as poss...

17 English Installation Pr oc edur e b After pouring some water, reassemble the rubber cap on the connection part of a flexible hose of the indoor unit and firmly tighten it with a band to prevent leakage. c Check the leak test at the part where the adhesive for the flexible hose and the drain pipe ...

18 Installation Procedure English Installation Pr oc edur e ࡛ To protect the product from water and possible shock, you should keep the power and the communication cables of the indoor and outdoor units in the iron pipe. ࡛ Connect the power cable to the auxiliary circuit breaker (ELCB, MCCB, ELB). ࡛...

19 English Installation Pr oc edur e Norminal dimensions for cable (mm²) Norminal dimensions for screw (mm) B D d1 E F L d2 t Standard dimension (mm) Allowance (mm) Standard dimension (mm) Allowance (mm) Standard dimension (mm) Allowance (mm) Min. Min. Max. Standard dimension (mm) Allowance (mm) Min...

20 Installation Procedure English Installation Pr oc edur e Example of Installation Ɵͱϩɇ̷Χͱиʪθʀɇɵ̷ʪ̷ʪ͝˝ϩ˵ø॔ߣߢߢ࣑͔࣒ࡥÃ̈͝ϩ̈ɇ̷ΧЇ̷̷ࣛ̈͝ʀЇθθʪ͝ϩ॔ߣߢࣈࣉࡥŵЇ̈͝͝͝˝ʀЇθθʪ͝ϩͱ˙ʪɇʀ˵Ї̈͝ϩϑ॔ߣࣈࣉࡥƟͱϩɇ̷ߣߢ̈͝ʒͱͱθ units were installed or 10 [A] ELCB MCCB+ELB 9 [A] 1 [A] 0[m] 10[m] 20[m] 100[m] Indoor unit 1 Indoor unit 2 Indoor...

21 English Installation Pr oc edur e 2 As shown in the figure, peel off the shields from the rubber and wire of the power cable. ࡛ Peel off 20 mm of cable shields from the pre-installed tube. Power cable (Unit: mm) 20 20 20 60 120 180 Pre-installed tube for the power cable 20 20 20 60 120 180 CAUTIO...

22 Installation Procedure English Installation Pr oc edur e CAUTION ࡛ Make sure that the connection parts are not exposed to outside. ࡛ Be sure to use insulation tape and a contraction tube made of approved reinforced insulating materials that have the same level of withstand voltage with the power ...

23 English Installation Pr oc edur e Take the steps presented in the following table: Steps Remote control display 1 Set the SEG2 and SEG3 values: a Set the SEG2 value by pressing the (Low Fan) button repeatedly until the value you want to set appears on the remote control display. SEG2 b Set the SE...

24 Installation Procedure English Installation Pr oc edur e Steps Remote control display b Set the SEG8 value by pressing the (High Fan) button repeatedly until the value you want to set appears on the remote control display. SEG8 When you press the (Low Fan) or (High Fan) button, values appear in t...

27 English Installation Pr oc edur e 3 Check whether the option values that you have set are correct by pressing the (Mode) button repeatedly [SEG2, SEG3] [SEG11 , SEG12 ] [SEG21 , SEG22 ] [SEG4, SEG5] [SEG14 , SEG15 ] [SEG23 , SEG24 ] [SEG6, SEG8] [SEG16 , SEG17 ] [SEG9, SEG10 ] [SEG18 , SEG20] 4 S...

28 Installation Procedure English Installation Pr oc edur e Option SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 Function Page - Setting RMC address - Group channel (x16) Group address Indication and details Indication Details - Indication Details - Indication Details Indication Details 1 0 No RMC address RMC1 0...

29 English Installation Pr oc edur e Installation options for the 02 series SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 0 2 Evaporator Drying Use of external room temperature ϑʪ͝ϑͱθࢩđ͔̈̈̈͝ї͝˝ fan operation when thermostat is off Use of central control FAN RPM compensation SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 1 Use o...

32 Installation Procedure English Installation Pr oc edur e ࡒʒЭɇ͝ʀʪʒ˙Ї͝ʀϩ̈ͱ͝ࡤAͱ͝ϩθͱ̷̷̈͝˝ʀͱͱ̷̈͝˝ࢩ˵ʪɇϩ̈͝˝ʀЇθθʪ͝ϩͱθΧͱиʪθϑɇӬ͝˝ӥϩ˵͔ͱϩ̈ͱ͝ʒʪϩʪʀϩ࢏ (*1) When Cooling or dry mode is off. The indoor fan operate in setting minutes. (*2) Minimizing fan operation when thermostat is off - Fan operates for 20 sec...

33 English Installation Pr oc edur e 05 series installation option SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 0 5 Use of Auto Change Over for HR only in Їϩͱ͔ͱʒʪࢩƸϑʪͱ˙ Cooling only indoor unit of HR (When setting SEG3) Standard heating temp. Offset (When setting SEG3) Standard cooling temp. Offset (When setting S...

36 Installation Procedure English Installation Pr oc edur e (* 1) Duration for Auto Change Over triggered when you set dual set points in the Auto mode using the wired remote control MWR-WG00*N. During the automatic heating operation, if the specified time has elapsed in the state of "the room t...

38 Installation Procedure English Installation Pr oc edur e Changing the addresses and options individually When you want to change the value of a specific option, refer to the following table and follow the steps in Common steps for setting the addresses and options on page 22 . Option SEG1 SEG2 SE...

39 English Installation Pr oc edur e Performing final check and trial operation To complete the installation, perform the following checks and tests to ensure that the air conditioner operates correctly. 1 Check the followings. ࡛ Strength of the installation site ࡛ Tightness of pipe connection to de...

40 Installation Procedure English Installation Pr oc edur e Setting up the ETO Communication between indoor and outdoor units (F1 and F2) Error output port (1, 2) Contact input port (5, 6) Main indoor unit Sub indoor unit External contact interface module MIM-B14 Main indoor unit 1 Disable the exter...

41 English Installation Pr oc edur e Sub indoor unit (BackUp Unit) 1 (Required) Enable the external contact control (with the installation option 02 series SEG14 - Reverse Control). 2 Connect the S-net pro2 to F1 and F2. 3 Enable the entrance control and set the mode, set temperature, and fan speed ...

42 English A ppendix Appendix Troubleshooting Detection of errors ࡛ If an error occurs during the operation, an LED flickers and the operation is stopped except the LED. ࡛ If you re-operate the air conditioner, it operates normally at first, then detect an error again. LED Display on the receiver &a...