Samsung AC100RN4PKG/EU - Manuals

5 English Safety Inf ormation Do not install the product in a place where thermo-hygrostat is needed (such as server room, machinery room, computer room, etc.) • Those places do not provide guaranteed operation condition of the product therefore performance can be poor in these places. FOR POWER SUP...

6 English Safety Information Safety Information Safety Inf ormation To reinstall the air conditioner, please contact your nearest service centre. • Failing to do so may result in problems with the product, water leakage, electric shock, or fire. • A delivery service for the product is not provided. ...

7 English Safety Inf ormation Do not use this air conditioner for long periods of time in badly ventilated locations or near infirm people. • Since this may be dangerous due to a lack of oxygen, open a window at least once an hour. Do not use means to accelerate the defrost operation or to clean, ot...

9 English Safety Inf ormation This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsi...

10 English Indoor Unit Overview A t a Glanc e Indoor Unit Overview At a Glance 01 Display Operation status Indication on the display Power on Ice blue (blinking) In operation Ice blue Stopped Off Timed on/off function Blue Requires filter cleaning Yellow green Defrost function Ice blue (blinking onc...

11 English A t a Glanc e Operating temperature and humidity Mode Outdoor temperature Indoor temperature Indoor humidity Cool mode -15°C to 50°C 18°C to 32°C 80% or less Heat mode -20°C to 24°C 30°C or less - Dry mode -15°C to 50°C 18°C to 32°C 80% or less CAUTION • If you use the air conditioner at ...

12 English Cleaning and Maintaining Cleaning and Maint enanc e Cleaning and Maintaining Cleaning and Maintenance Cleaning the indoor unit exterior Wipe the surface of the unit with a slightly wet or dry cloth when needed. Wipe off dirt from odd-shaped areas by using a soft brush. CAUTION • Do not us...

13 English Cleaning and Maint enanc e Cleaning the air filter NOTE • Clean the air filter once every two weeks. • Spray water or use a vacuum cleaner to remove dust. • After removing dust, dry the air filter completely. – Avoid direct sunlight. Failure to do so may deform the air filter. Reassemblin...

14 English Cleaning and Maintaining Cleaning and Maint enanc e Periodical maintenance Unit Maintenance item Interval Requires qualified technicians Indoor unit Clean the air filter. At least once a month Clean the condensate drain pan. Once a year Required Clean up the heat exchange. Once a year Req...

15 English Cleaning and Maint enanc e Troubleshooting Refer to the following chart if the air conditioner operates abnormally. This may save time and unnecessary expense. Problem Solution The air conditioner does not operate immediately after it has been restarted. • Because of the protective mechan...

18 English Cleaning and Maintaining Cleaning and Maint enanc e Problem Solution Steam is produced on the indoor unit. • In winter, if the indoor humidity is high, steam may be produced around the air outlet while the defrost function is running. This is a normal operation. The outdoor unit fan conti...

19 English Cleaning and Maint enanc e Information about refrigerant Important information: regulation regarding the refrigerant used This product contains fluorinated greenhouse gases. Do not vent gases into the atmosphere. CAUTION • If the system contains 5 tCO₂e or more of fluorinated greenhouse g...

Samsung, PO Box 12987, Blackrock, Co. Dublin. IEor Euro QA Lab. Saxony Way, Yateley, Hampshire GU46 6GG, UK This appliance is filled with R-32. QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT UK 0333 000 0333 www.samsung.com/uk/ support IRELAND (EIRE) 0818 717100 www.samsung.com/ie/ suppor...

5 Installation Pr ocedur e English Installation Procedure Step 1 Checking and preparing accessories The following accessories are supplied with the indoor unit. The type and quantity may differ, depending on the specifications. Insulation pipe Cable-tie Drain hose Installation manual Clamp User manu...

7 Installation Pr ocedur e English ŷ The circular panel is by default available in exposed installation. ŷ Make inspection holes on the ceiling for easier installation and maintenance, as shown in the following table. (The size of an inspection hole must be at least 450 mm x 450 mm.) ŷ A suspended c...

8 Installation Procedure Installation Pr ocedur e English ŷ Do not hold the discharge while carrying the indoor unit to avoid the possibility of breakage. ŷ You must hold the hanger plate on the corner and carry the indoor unit. Step 3 Optional: Insulating the body of the indoor unit If you install ...

9 Installation Pr ocedur e English 2 Perform the following steps to install inspection holes in accordance with the panel type. a For the recessed installation of the square panel. ŷ Install an inspection hole to the direction of connection parts of the refrigerant pipe and the drain hose. (1 point)...

10 Installation Procedure Installation Pr ocedur e English 7 Adjust the unit to the appropriate position, taking into account the installation area for the front panel. ŷ Place the pattern sheet on the indoor unit. ŷ Adjust the space between the ceiling and the indoor unit by using a dimension gauge...

11 Installation Pr ocedur e English 5 Check that the flaring is correct, referring to the illustrations below for examples of incorrect flaring. Correct Inclined Damaged Surface Cracked Uneven Thickness Step 7 Connecting the assembly pipes to the refrigerant pipes There are two refrigerant pipes of ...

12 Installation Procedure Installation Pr ocedur e English Step 8 Performing the gas leak test To identify potential gas leaks on the indoor unit, inspect the connection area of each refrigerant pipe using a leak detector for R-410A. Before recreating the vacuum and recirculating the refrigerant gas...

13 Installation Pr ocedur e English Pipe Pipe size (mm) Insulation type (heating/cooling) Remarks Standard (Less than 30°C, 85%) High humidity (Over 30°C, 85%) EPDM, NBR (mm) Liquid pipe Ø6.35 to Ø9.52 9t 9t The internal temperature is higher than 120°C. Ø12.7 to Ø19.05 13t 13t Gas pipe Ø6.35 13t 19...

14 Installation Procedure Installation Pr ocedur e English CAUTION Check that the indoor unit is level with the ceiling by using the leveller. ŷ Install air ventilation to drain condensation smoothly. Air ventilation Ceiling ŷ If it is necessary to increase the height of the drain pipe, install the ...

15 Installation Pr ocedur e English ŷ Max. allowable bending angle. Indoor unit Max. 30˚ NOTE ŷ If a concentrated drain pipe is installed, refer to the figure below. Centralized horizontal drain pipe (more than 1/100 slope) Main drain pipe Full thread bolt hanger 1000 to 1500 mm 300 to 550 mm 200 mm...

16 Installation Procedure Installation Pr ocedur e English CAUTION ŷ When the float switch is not detected due to insufficient water on the drain pan, the drain pump will not work. ŷ If the power supply is directly connected to the L and N terminals, communication error message might appear. ŷ After...

17 Installation Pr ocedur e English Step 13 Optional: Installing DPM (Digital Packaged Multi) NOTE To find DPM allowable indoor unit models according to outdoor unit models, refer to outdoor installation manual. ŷ When installing DPM, you should set "DPM setting" to the outdoor unit. ŷ You d...

18 Installation Procedure Installation Pr ocedur e English Wiring terminals) 3 phase 1(L) 2(N) L1(R) L2(S) L3(T) N F1 F2 F1 F2 L N Indoor power Main power cable Communication cable Indoor unit Outdoor unit NOTE ŷ Insert the power and the communication cables to the cable insert hole, then arrange an...

19 Installation Pr ocedur e English Step 15 Optional: Extending the power cable 1 Prepare the following tools. Tools Spec Shape Crimping pliers MH-14 Connection sleeve (mm) 20xØ6.5 (HxOD) Insulation tape Width 19 mm Contraction tube (mm) 70xØ8.0 (LxOD) 2 As shown in the figure, peel off the shields ...

20 Installation Procedure Installation Pr ocedur e English 5 Apply heat to the contraction tube to contract it. Method 1 Method 2 Contraction tube Contraction tube 6 Wrap it with the insulation tape twice or more and position your contraction tube in the middle of the insulation tape. Method 1 Metho...

23 Installation Pr ocedur e English Steps Remote control display 9 Set the SEG11 and SEG12 values: a Set the SEG11 value by rotating the Wheel counterclockwise until the value you want to set appears on the remote control display. SEG11 b Set the SEG12 value by rotating the Wheel clockwise until the...

25 Installation Pr ocedur e English 3 Check whether the option values that you have set are correct by pressing the (Mode) button repeatedly [SEG2, SEG3] [SEG11, SEG12] [SEG21, SEG22] [SEG4, SEG5] [SEG14, SEG15] [SEG23, SEG24] [SEG6, SEG8] [SEG16, SEG17] [SEG9, SEG10] [SEG18, SEG20] 4 Save the optio...

27 Installation Pr ocedur e English Steps Remote control display 3 Set the SEG4 and SEG5 values: a Set the SEG4 value by pressing the (Low Fan) button repeatedly until the value you want to set appears on the remote control display. SEG4 b Set the SEG5 value by pressing the (High Fan) button repeate...

28 Installation Procedure Installation Pr ocedur e English Steps Remote control display b Set the SEG10 value by pressing the (High Fan) button repeatedly until the value you want to set appears on the remote control display. When you press the (Low Fan) or (High Fan) button, values appear in the fo...

31 Installation Pr ocedur e English Setting the indoor unit addresses Option No. for an indoor unit address: 0AXXXX-1XXXXX-2XXXXX-3XXXXX Before installing an indoor unit, be sure to set an address for the indoor unit by taking the following steps: 1 Make sure that the power is supplied to the indoor...

32 Installation Procedure Installation Pr ocedur e English CAUTION ŷ The main address must be set to a value in the range 0 to 15. If you set other values, communication error will occur. ŷ If any of SEG5 and SEG6 is set to a value in the range A to F, the main address of the indoor unit does not ch...

33 Installation Pr ocedur e English Option SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 Function Page Use of external control Setting the output of external control S-Plasma ion Buzzer control Maximum filter usage time Indication and details Indication Details Indication Details Indication Details Indication...

34 Installation Procedure Installation Pr ocedur e English ŷ Even if you set the Use of drain pump (SEG8) option to 0, it is automatically set to 2 (the drain pump is used with 3 minute delay). Example: When installing DPM (1 Outdoor unit with 4 indoor units) Condition SEG14 Setting Result External ...

35 Installation Pr ocedur e English Installation Pr ocedur e Emergency Temperature Output (ETO) function CAUTION ŷ In order to deploy the ETO function, the MIM-B14, an external contact interface module, must be installed in each indoor unit. – The ETO is a concept of emergency operation of indoor un...

36 Installation Procedure English Installation Pr ocedur e ETO operation specifications 1 Main indoor unit – Based on the external contact control settings, the main indoor unit decides whether to generate output when an error (indoor unit stop) occurs. – Based on the ETO settings, the main indoor u...

37 English Appendix Troubleshooting Condition Indoor unit display indications Ice blue Yellow green Blue Red Power reset (blinking once every 2 seconds) X X X In the defrost operation (blinking once every 10 seconds) X X X Open or short circuit error of the indoor-temperature sensor X X X Error of t...