Royal Sovereign 1650C - Manuals

Page 2 - TABLE OF CONTENTS

TOPICS PAGE INSTRUCTION --------------------------------------------------------------- 3 SAFETY PRECAUTIONS ------------------------------------------------------ 3 CHARACTERISTICS ----------------------------------------------------------- 4 SPECIFICATIONS -----------------------------------------...

Page 3 - SAFETY PRECAUTIONS; INSTRUCTION

Thank you for purchasing a Royal Sovereign Roll Laminator. It has been designed and manufactured to provide years of continuous service in the professional environment. To insure high quality lamination, please read this instruction manual thoroughly. This manual will provide you with complete opera...

Page 4 - Description; SPECIFICATIONS

RS Roll Laminator Line is advanced laminators with time transcendental design, utilizing thelatest in laminating technology.It is designed for you to set temperature and speed as necessary. Also you can laminate anything at high speed,regardless of thickness of material and type of film.It is also d...

Page 5 - NAMES OF MAJOR PARTS OF MACHINE

NO 123456789 10111213 ○ TAKE-UP BOBBIN IDLE BAR HOT ROLLER TABLE-FRONT UPPER ROLLER ○ ○ X TAKE-UP SWITCH ○ ○ PART NAME FRAME-GUIDE,PAPER RSC-1650H RSC-1650H NAMES OF MAJOR PARTS OF MACHINE CONTROL PANEL ○ FOOT SWITCH ○ ASS'Y-STAND PRESSURE LEVER TENSION CONTROL KNOB SAFETY COVER ○ REMOCON SWITCH ○ ○...

Page 6 - SETTING UP FILM; COLD FILM

1. Set the glossy side of upper/lower film to face the heat. ( Glossy side is PET film and matte side is thermal polymer laminating film.) 2. Like picture 1, insert core into the left side of upper/lower film shaft.3. Like picture 2 and 3, insert core into the right side of upper/lower film. 4. Like...

Page 7 - HANGING FILM

1. Set up cold film below the upper bar of the machine. (Set the same as methord of the HOT film for protect paper of lower part) 2. Set the pressure lever to the 15mm, open mode. 3. Insert a piece of wide cardboard (guiding paper/carrier) between the rollers. 4. Pull the film from the upper roller ...

Page 8 - CONTROL OF ROLLER PRESSURE

1. For setting, pull the pressure lever out and turn the lever to following the indication 2. OPEN/15mm(Board) : For laminating 15mm thick board (RSC-1650H/1650C) 3. 10~13mm(Board) : For laminating 10~13mm thick board 4. 5~7mm(Board) : For laminating 5~7mm thick board 5. 1mm(Hard Board) : For lamina...

Page 9 - INSTRUCTIONS FOR CONTROL PANEL

We designed this machine standing by user’s convenience. You can manipulate speed and temperature . ***Terms*** INSTRUCTIONS FOR CONTROL PANEL 6 1 4 2 6 2 1 3 3 5 - 9 -

Page 10 - FUNCTIONS OF CONTROL PANEL

1. FUNCTIONS OF CONTROL PANEL RUN/STOP BUTTON : Run or stop the rollers SPEED BUTTON : Increase or decrease speed LED OF SPEED : Display or speed LED OF TEMP. : Display temperature TEMP.BUTTON : Increase or decrease temperature REVERSE BUTTON : To make the rollers run backward 2.HOW TO USE BUTTONS P...

Page 11 - LAMINATING STEPS

1. Put cold roll film on upper bar.(Set the same as methord of the HOT film for protect paper of lower part)2. Pull COLD film, and fix it so that backside protecting paper can be wound on take-up mandrel clockwise. (Revolve core to make protectingpaper tight a little bit.)3. Set pressure lever at th...

Page 12 - METHOD FOR USING CUTTER

**Cross Cutter** 1. It is on the back side of the machine. 2. After lamination, move cutter to a point about 1/3 of the width of lamination. 3. Grasp film with one hand and press the cutter, cutter downward and slide it to the direction intending to cut with another hand. 4.Press the cutter and slid...

Page 14 - CHECK POINT; ASSEMBLY PARTS; Cause

CHECK POINT *Rollers do not operate 1. Check the power cord. after press RUN button 2. Check if the switch is on. 3. Check if the emergency switch is off. 4. Check the s/w of safety cover is right. *Wrinkled lamination 1. Adjust film tension. result 6 BOLT CORE 8 Washer( Φ 8) 6 Bolt(M8X12) 1. Power ...

Page 15 - WARRANTY

1. For six month from the date of purchase, Royal Sovereign International Corporation or its authorized service center will repair this product free of charge if it is defective in material or workmanship. 2. This Limited Warranty does not include cleaning, or damage caused by accident, neglect, mis...