Regency 510-994 - Manuals - manualsarea.com

Page 2 - P33 Gas Fireplace; Approved Venting Systems; * The unit must be raised a minimum of 1” above the; LP4 Gas Fireplace, the burner ori; Gas Fireplaces

Model P33-NG4 w/ Contemporary Faceplate P33-LP4 w/ Contemporary Faceplate Fuel Type Natural Gas Propane Minimum Supply Pressure 5” W.C. (1.25 kPa) 12” W.C. (3.00 kPa) Manifold Pressure - High 3.8” W.C. (0.95 kPa) 11” W.C. (2.74 kPa) Manifold Pressure - Low 1.1” W.C. (0.27 kPa) 3.3” W.C. (0.82 kPa) O...

Page 3 - Framing and Finishing; fl; Combustible Mantels; Drywall; Side View; Mantel Leg Clearances; WARNING; Clearance Requirements

Framing and Finishing 1) Determine the total thickness of facing material (e.g. drywall plus ceramic tiles) to allow the fi nished surface to be fl ush with the front of the unit. Total facing thickness can vary from 1/2” (13mm) to 1-¼” (32mm) thick. 2) Frame in the enclosure for the unit with frami...

Page 4 - Dimension; Installation of this; Due to ongoing product development, product appearance and speci

P33 Gas Fireplace Combustible Mantels with Contemporary Faceplate Because of the extreme heat this fi replace emits, the mantel clearances are critical. Combustible mantel clearances from top of the louvers are shown in the diagram below. Mantel may be installed anywhere in the shaded area or higher...

Page 5 - Horizontal Terminations Only; Important; Snorkel Terminations; Snorkel Terminations:; cations Book

6-7/8" (173mm) dia. Flue pipe 4" (102mm) dia. flue pipe Wall Thimble (2 pc) Termination Cap (Part# 946-523/P) AstroCap TM springspacer FPI Direct Vent System (Flex) Horizontal Terminations Only This venting system, in combination with the P33 Direct Vent Gas Fireplace, have been tested and l...

Page 6 - Rigid Pipe System; ertical; Alternate Horizontal

Rigid Pipe Venting Horizontal or Vertical Terminations Venting Arrangements - Vertical Terminations Rigid Pipe System (Propane & Natural Gas) The P33 is approved for a maximum 40 ft. straight vertical, with Rigid Pipe vent systems for Propane and Natural Gas. The lightly shaded area, 6 8 2 0 4 1...

Page 7 - Two 45° elbows = One 90° elbow; Vertical Venting with Two (2) 90° Elbows; Option; Two 45° elbows = One 90° elbow; Option; Two 45° elbows = One 90° elbow; Option

Vertical Venting with Two (2) 90° Elbows - Initial vertical section. Two 45° elbows = One 90° elbow Option V H V+ V1 Maximum total pipe: length, of all sections, must not exceed 30 feet. Total horizontal sections must not exceed 8 feet. Minimum of 1 foot between 90° elbows is required. A) 1’ Min. 4’...

Page 8 - using one 45° and one; Maintain clearances to combustibles.; refer to Exterior; * Unit must be raised by 1” when using

Venting Arrangements - Horizontal Terminations This lightly shaded area of the diagram shows allowable combinations of vertical runs with horizontal terminations, using one 45° and one 90° elbow (two 45º elbows equal one 90° elbow). Note: Must use optional rigid pipe adapter (Part # 510-994) when us...

Page 10 - Vertical termination with co-linear; The appliance must not be connected to a chimney; Please refer to Exterior Vent Terminations for

Flex Liner Exhaust Flue A maximum of two certified joiner kits may be used per length. #948-305 35 ft (11m) Air Intake Co-linear DV Vertical Termination Cap # 946-529 Co-Linea Flex Adapter with Kit# 946-563 Outer Pipe with Kit# 946-563 Inner Pipe Adapter with Kit# 946-563 Rigid Pipe Adapter # 510-99...