RedMax SGCZ2450S - Manuals - manualsarea.com

Page 2 - SAFETY FIRST; symbol; NOTE; Contents; WARNING

US-2 SGCZ2450S SAFETY FIRST Instructions contained in warnings withinthis manual marked with a symbol concern critical points which must betaken into consideration to preventpossible serious bodily injury, and for thisreason you are requested to read all suchinstructions carefully and follow themwit...

Page 4 - Warning labels on the machine; FUEL TANK CAP; Symbols on the machine; EMISSION CONTROL INFORMATION; EMISSION CONTROL; An emission control label is located on the engine.

US-4 SGCZ2450S 3. Warning labels on the machine For safe operation and maintenance, symbolsare carved in relief on the machine. Accordingto these indications, please be careful not totake a mistake. (a) The port to refuel the "MIX GASOLINE" Position: FUEL TANK CAP (b) The direction to close ...

Page 5 - For safe operation

US-5 SGCZ2450S U S • A brushcutter or trimmer can be dangerous if used incorrectly orcarelessly, and can cause serious orfatal injury to the operater or others. Itis extremely important that you readand understand the contents of thisOwner's manual. • Under no circumstances may the design of the mac...

Page 6 - Using the product; IMPORTANT

US-6 SGCZ2450S contain dangerous carbon monoxide. 10. Never to touch the spark plug or plug cord while the engine is in operation Doing somay result in being subjected to anelectrical shock. 11.Never to touch the muffler, spark plug, other metallic parts of the engine orengine cover while the engine...

Page 8 - In the event that any part must be; Disposal

US-8 SGCZ2450S 5. For safe operation lubricant, always be sure to use onlyRedMax products or products whichhave been certified by RedMax for usewith the RedMax product. 5. In the event that any part must be replaced or any maintenance or repairwork not described in this manual mustbe performed, plea...

Page 9 - BLADE GUARD

US-9 SGCZ2450S U S 6. Set up ■ MOUNTING ENGINE (SE1) 1. Install the engine to the driveshaft so that the cylinder head and the stopswitch may come on the same side. 2. Using attached four bolts, secure the connection firmly with equal force(Torque: 25in-lbs)(Torque: 2.8 N.m.). (1) Bolt(2) Stop switc...

Page 12 - STARTING ENGINE; ADJUSTING THROTTLE CABLE

US-12 SGCZ2450S 8. Operation ■ STARTING ENGINE The cutting head will start rotatingupon the engine starts. 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground andclear of surrounding objects as it willstart rotating upon starting of theengine. 2. Push the primer pump several...

Page 13 - HOW TO USE; CUTTING WORK

US-13 SGCZ2450S U S 8. Operation OP7 OP8 OP9 OP10 OP11 OP12 OP13 OP14 ■ HOW TO USE • Adjust the front handle to the most comfortable position. • Start the engine and pull the throttle lever gradually. The blades will startmoving as the engine speed goes up. • To stop the blade motion, simply release...

Page 14 - ENGINE; MAINTENANCE CHART

US-14 SGCZ2450S To remove blades: 1. Turn over the machine and remove the bottom cover (MA3-1) by removing the4 screws. 2. Loosen 4 screws and remove the lower blade (MA3- 2) 3. Loosen 4 screws and remove the upper blade (MA3-3), To install blades: The upper and lower blades areinterchangeable. When...

Page 17 - Troubleshooting guide

US-17 SGCZ2450S U S 13. Troubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank ➞ incorrect fuel ➞ drain it and with correct fuel fuel filter ➞ fuel filter is clogged ➞ clean carburetor adjustment screw ➞ out of normal range ➞ adjust to normal range sparking (no spark) ...

Page 18 - Repair or replacement of any warranted part under the warranty

US-18 SGCZ2450S The EPA (U.S. Environmental Protection Agency), CARB (California Air Resources Board), EnvironmentCanada and RedMax are pleased to explain the emissions control system's warranty on your 2009 and latersmall off-road engine. In U.S. and Canada, new equipment that use small off-road en...

Page 19 - by a failure under warranty of any warranted part.

US-19 SGCZ2450S U S warranty is warranted for the remaining warranty period. Any warranted part that is scheduled only for regularinspection in the maintenance schedule will be warranted for a period of two years. A statement in such writteninstructions to the effect of "repair or replace as nec...