RedMax PSZ2460S - Manuals - manualsarea.com

Page 2 - POLE SAW; WARNING

US-1 PSZ2460S U S 115 35 78-10 (003) PSZ2460S OWNER 'S/ OPERATOR'SMANUAL POLE SAW WARNING The engine exhaust from thisproduct contains chemicalsknown to the State of California tocause cancer, birth defects orother reproductive harm. WARNING Before using our products,please read this manual carefull...

Page 3 - Contents; SAFETY FIRST; symbol concern critical; NOTE

US-2 PSZ2460S 1. Parts location ......................................................................32. Specifications .....................................................................33. Warning labels on the machine ..........................................44. Symbols on the machine ..........

Page 5 - EMISSION CONTROL INFORMATION; EMISSION CONTROL

US-4 PSZ2460S 3. Warning labels on the machine For safe operation and maintenance, symbols arecarved in relief on the machine. According to theseindications, please be careful not to take a mistake. (a) The port to refuel the "MIX GASOLINE" Position: FUEL TANK CAP (b) The direction to close ...

Page 6 - For safe operation

US-5 PSZ2460S U S 1. Read this manual carefully until you completely understand and follow allsafety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever anyquestions arise. Also note, if you haveany questions which cannot beanswered herein, contact the de...

Page 8 - HANDLING FUEL

US-7 PSZ2460S U S 5. For safe operation have been certified by RedMax for usewith the RedMax product . 4. In the event that any part must be replaced or any maintenance or repair work notdescribed in this manual must beperformed, please contact a representativefrom the store nearest RedMax authorize...

Page 9 - • Never use a cracked or warped guide; IMPORTANT

US-8 PSZ2460S 5. For safe operation • Never use a cracked or warped guide bar: replace it with a serviceable oneand make sure it fits properly. • If a saw blade should bind fast in a cut, shut off the engine immediately. Pushthe branch or tree to ease the bind andfree the blade. • Do not operate the...

Page 11 - Fuel and Chain Oil

US-10 PSZ2460S 7. Fuel and Chain Oil ■ FUEL • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine andallow it cool before refueling the unit. Select outdoor bareground for fueling and move at least 10 ft (3 m) away fromthe fueling point b...

Page 13 - STARTING ENGINE; CHECKING OIL SUPPLY

US-12 PSZ2460S 8. Operation ■ STARTING ENGINE The cutting head will start rotatingupon the engine starts. 1. Feed fuel and chain oil into their respective tanks and tighten the capssecurely. (OP1) (1) Fuel (2) Chain oil 2. Rest the unit on a flat, firm place. Keep the cutting head off the ground and...

Page 14 - ADJUSTING THROTTLE CABLE

US-13 PSZ2460S U S ■ ADJUSTING OIL FLOW RATE Never fill the oil reservoir nor adjustthe oiler with the engine running. An increase in bar oil flow rate will speedoil consumption, requiring more frequentchecks on the oil reservoir. To ensuresufficient lubrication, It may be necessaryto check the oil ...

Page 15 - MAINTENANCE CHART

Maintenance, replacement, or repair of the emission control device and systems may be performed by anynon-road engine repair establishment or individual. US-14 PSZ2460S ■ OILING PORT Dismount the guide bar and check theoiling port for clogging. (MA1) (1) Oiling port ■ GUIDE BAR Remove sawdust in the...

Page 18 - Troubleshooting guide

US-17 PSZ2460S U S Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank ➞ incorrect fuel ➞ drain it and with correct fuel fuel filter ➞ fuel filter is clogged ➞ clean carburetor adjustment screw ➞ out of normal range ➞ adjust to normal range sparking (no spark) ➞ spark plug is fouled/wet ...