RedMax LRTZ2500 - Manuals

❲ 6 ❳ 5. For safe operation 1. R e a d t h i s m a n u a l c a r e f u l l y u n t i l y o u completely understand and follow all safetyand operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Alsonote, if you have any questions which cann...

❲ 7 ❳ b. At night, at times of heavy fog, or at any other t i m e s w h e n y o u r f i e l d o f v i s i o n m i g h t b elimited and it would be difficult to gain a clearview of the working area. c. During rain storms, during lightning storms, at times of strong or gale-force winds, or at anyother...

❲ 8 ❳ ■ BEFORE STARTING THE ENGINE 1. The area within a perimeter of 50 feet (15m) of t h e p e r s o n u s i n g t h e p r o d u c t s h o u l d b econsidered a hazardous area into which no oneshould enter. If necessary yellow warning rope,w a r n i n g s i g n s s h o u l d b e p l a c e d a r o u...

❲ 9 ❳ Never place the throttle into the high speedposition when starting the engine. 3. After starting the engine, check to make sure that the cutting attachment stops rotating whenthe throttle is moved fully back to its originalposition. If it continues to rotate even after thethrottle has been mov...

❲ 10 ❳ • IF SOMEONE COMES1. Guard against hazardous situations at all times. Warn adults to keep pets and children awayfrom the area. Be careful if you are approached.Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off t...

❲ 11 ❳ 5. For safe operation ■ HANDLING FUEL 1. The engine of the RedMax product is designed to run on a mixed fuel which contains highlyflammable gasoline. Never store cans of fuel orrefill the tank of the unit in any place where thereis a boiler, stove, wood fire, electrical sparks,welding sparks,...

6. Set up ❲ 13 ❳ SE4 ■ ATTACHING THE TRIMMING MECHANISM (SE4) 1. Remove the cap on the end of the main pipe.2. Remove the screw screwed into the end of the trimming mechanism. 3. Insert the end of the trimming mechanism into the main pipe. 4. Line up the hole on the end of the trimming m e c h a n i...

container to avoid mixing up with gasoline orother containers. 6. Indicate the contents on outside of container for easy identification. ■ FUELING THE UNIT 1. Untwist and remove the fuel cap. Rest the cap on a dustless place. 2. Put fuel into the fuel tank to 80% of the full capacity. 3. Fasten the ...

❲ 16 ❳ ■ STARTING ENGINE The cutting head will start rotating upon theengine starts. 1. Rest the unit on a flat, firm place. Keep the c u t t i n g h e a d o f f t h e g r o u n d a n d c l e a r o fsurrounding objects as it will start rotating uponstarting of the engine. 2. P u s h t h e p r i m e ...

8. Operation ■ STOPPING ENGINE (OP3) 1. Release the throttle lever and run the engine for a half minute. 2. Shift the ignition switch to the STOP position. • Except for an emergency, avoid stopping the engine while pulling the throttle lever. ■ ADJUSTING THROTTLE CABLE • The normal play is 1 or 2mm ...

is in operation. • Always be sure to turn off the engine before changing the angle of the blades, removingbranches which have become stuck in theblades, or at any other time when coming intoclose proximity with the blades. • Always wear work gloves made of leather or some other sturdy material when ...

❲ 19 ❳ 9. Maintenance ■ BLADES (MA1) • When refilling the tank or resting, it is often a g o o d i d e a t o u s e t h e t i m e t o o i l t h e c u t t i n gblades. • If a gap exists between the upper and lower blades, follow the procedure below to adjustthem so that they fit more closely together....

❲ 20 ❳ QUICK TIPIf the blades become so worn down that it is nolonger possible to eliminate the gap between them,y o u s h o u l d c o n t a c t t h e a u t h o r i z e d R e d M a xservicing dealer from which you purchased yourRedMax® trimmer to have the blades resharpenedor replaced. ■ GEAR CASE T...

❲ 22 ❳ 9. Maintenance ■ INTAKE AIR COOLING VENT • Never touch the cylinder, muffler, or spark plugs with your bare hands immediately afters t o p p i n g t h e e n g i n e . T h e e n g i n e c a nb e c o m e v e r y h o t w h e n i n o p e r a t i o n , a n ddoing so could result in severe burns. •...

❲ 23 ❳ 10. Storage • A g e d f u e l i s o n e o f m a j o r c a u s e s o f e n g i n e starting failure. Before storing the unit, empty thefuel tank and run the engine until it uses all thefuel left in the fuel line and the carburetor. Storethe unit indoor taking necessary measures forrust prevent...

❲ 24 ❳ 11. Troubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank ➞ incorrect fuel ➞ drain it and with correct fuel fuel filter ➞ fuel filter is clogged ➞ clean carburetor adjustment screw ➞ out of normal range ➞ adjust to normal range sparking (no spark) ➞ spark plug ...

12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair ...

The California Air Resources Board and KOMATSU ZENOAH are pleased to explain theemission control system warranty on your 1995 and later small off-road engine. In California,new small off-road engines must be designed, built and equipped to meet the state’s stringentanti-smog standards. KOMATSU ZENOA...

EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE MODEL LRTZ2500, UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECT...