Raypak B-195 - Manuals - manualsarea.com

Page 3 - RECEIVING EQUIPMENT; warranty conditions, you must also specify date of installation.; GENERAL SPECIFICATIONS; Sanitation Foundation,; NSF; Input

3 1. RECEIVING EQUIPMENT On receipt of your equipment it is suggested that you visually check for external damage to the carton. If the carton is damaged, it is suggested that a note be made on the Bill of Lading when signing for equipment. Removethe heater from the carton and if it is damaged repor...

Page 5 - VENTING

Measures must be taken to prevent the entry of corrosive chemical fumes to the combustion and ventilation air supply. Such chemicals include, but are not limited to, chlorinated and/or fluorinated hydrocarbons such asfound in refrigerants, aerosol propellants, dry-cleaning fluids, degreasers, and pa...

Page 6 - Applies only to exhaust hood over cooking

6 Fig. #8975.3 Applies only to exhaust hood over cooking equipment.

Page 9 - Failure to do so can cause water damage

9 A drain valve is provided in the tank for draining water during servicing. The temperature and pressure relief valve is easily accessible through the front. A nipple is provided(shipped loose with the heater) for installation in theT & P relief valve. A drain line must be connected tothe nippl...

Page 10 - ELECTRICAL

ELECTRICAL The electrical power supply requirement for the heater is 120 volts, 60 Hz, 5.0 amps or less . Field wiring connections and electrical grounding must comply with the local codes, or in the absence of local codes, withthe latest edition of the National Electrical Code, ANSI/NFPA 70. NOTE: ...

Page 12 - SEQUENCE OF OPERATION; Provided the necessary power, water, gas and; START UP PROCEDURES; Fill the heater system with water purging all air. It; START UP AND OPERATION; COMPONENT LOCATION

SEQUENCE OF OPERATION The booster heater is designed to maintain a tempera-ture of 180 deg. F (82.2 Deg. C) of 490 GPH waterrequired for the rinse cycle of a commercial dish-washer. An inlet temperature of 140 Deg. F (60 Deg.C) will produce optimum results. Provided the necessary power, water, gas a...

Page 13 - SECTION 3. LIGHTING THE HEATER; If you do not follow these instructions; DOES NOT; Should overheating occur or the gas sup-

SECTION 3. LIGHTING THE HEATER Safety lighting and other performance criteria were met for the burner assembly and control assemblywhen the heater was tested for design certificationunder the ANSI Z21.10.3 Standard WARNING: If you do not follow these instructions exactly, a fire or explosion may res...

Page 14 - Label all wires prior to disconnection when; DANGER - SHOCK HAZARD; - Make sure electrical

SECTION 4.TESTING THE IGNITION SAFETY SHUT-OFF The ignition system safety shut-off must be tested byconducting the following method of tests: a) With the system power off, manually shut off the gas supply. b) Turn power back on, observe the igniter start to heat up and glow bright orange. c) After a...

Page 17 - Continuation TROUBLE SHOOTING GUIDE

Continuation TROUBLE SHOOTING GUIDE 3d. Excessive negative pressure exerted by the exhaust system on the vent willprevent N.O. combustion air/ventswitch from closing. Provide means torelieve pressure and close the N.O.switch. If combustion air/vent switchwill not close, replace switch. 3e. Disconnec...

Page 18 - REPLACEMENT PARTS LIST

18 6. REPLACEMENT PARTS LIST NOTE: To supply the correct part it is important that you state the model number, serial number and type of gas when applicable. Any part returned for replacement under standard company warranties must be properly tagged with RAYPAK return parts tag, completely filled in...

Page 23 - Raypak Canada Limited

Raypak, Inc. , 2151 Eastman Avenue, Westlake Village, CA 93030 (805) 278-5300 FAX (800) 872-9725 Raypak Canada Limited , 2805 Slough St., Mississauga, Ontario, Canada L4T 1G2 (416) 677-7999 FAX (416) 677-8036 Litho in U.S.A. www.raypak.com