Rangemaster LEIHDS120SC - Manuals

Page 2 - CONTENTS

CONTENTS IMPORTANT SAFETY INFORMATION Installation Page 2 Child Safety 2 Maintenance and service 3 YOUR APPLIANCE OPERATING INSTRUCTIONS Cooker Hood Controls 4 To Operate 5 Recirculation 5 Extraction 5 MAINTENANCE AND CLEANING Metal Grease Filters 6 Charcoal Filter 6 Lighting 7 Cleaning 7 INSTALLATI...

Page 3 - INSTALLATION; IMPORTANT SAFETY INFORMATION; CHILD SAFETY; DURING USE

These warnings are provided in the interests of safety. Ensure that you understandthem all before installing or using this appliance. Your safety is of paramount importance.If you are unsure about the meaning of any of these warnings contact the Helpline. • INSTALLATION • Any installation work must ...

Page 4 - MAINTENANCE AND SERVICE

IMPORTANT SAFETY INFORMATION • MAINTENANCE AND SERVICE • This appliance can be a hazard if thegrease filters and charcoal filters are notcleaned and replaced as recommended. • Always insist on genuine RANGEmasterspare parts. • Under no circumstances should youattempt to repair the appliance yourself...

Page 5 - OPERATING INSTRUCTIONS; COOKER HOOD CONTROLS; YOUR APPLIANCE

OPERATING INSTRUCTIONS The chimney hood is designed to extractunpleasant odours from the kitchen, it willnot extract steam. The appliance can beinstalled to recirculate or extract contaminated air. COOKER HOOD CONTROLS The chimney hood functions are controlledby four push buttons located centrally o...

Page 6 - EXTRACTION

TO OPERATE Select the required fan speed and light ifrequired. To obtain the best performance when cookingit is advisable to switch the chimney hood onfor a few minutes before you start cookingand leave it running for about 15 minutes after finishing. RECIRCULATION In the recirculation mode contamin...

Page 7 - METAL GREASE FILTERS; CHARCOAL FILTER; MAINTENANCE AND CLEANING

Regular maintenance and cleaning will ensure good performance and reliability, whileextending the working life of the hood. Special attention should be paid to the grease filter cassettes and the charcoal filter when the hood is used in the recirculation mode. Before carrying out any mainte- nance o...

Page 8 - LIGHTING; CLEANING

LIGHTING The canopy is fitted with three 20W halogenspotlamps. If one of the spotlamps fails tofunction check that the two pins are correctly inserted into the lamp holder. To replace a spotlamp remove the two screws, which secure the lens retaining ringand glass lens as illustrated. Take care toe n...

Page 9 - TECHNICAL INFORMATION; INSTALLATION INSTRUCTIONS

It is dangerous to alter the specifications or attempt to modify this chimney hood in any way. TECHNICAL INFORMATION DIMENSIONS CANOPY: Height 60mm Width 1198mm Depth 490mm CHIMNEY: Height - Upper Chimney 215mm Lower Chimney 740mm Width 300mm Depth 260mm ELECTRICAL SUPPLY VOLTAGE: ~50Hz 230V POWER C...

Page 10 - ELECTRICAL CONNECTION; THIS APPLIANCE MUST BE EARTHED

ELECTRICAL REQUIREMENTS Any permanent electrical installation mustcomply with the latest I.E.E. Regulations andlocal Electricity Board regulations. For yourown safety this should be undertaken by aqualified electrician e.g. your local ElectricityBoard, or a contractor who is on the roll ofthe Nation...

Page 11 - COMPONENTS; INSTALLATION REQUIREMENTS; INSTALLING THE CHIMNEY HOOD

COMPONENTS The chimney hood comprises of thefollowing: -No 1 150x120mm ducting spigot (A) No 1 120x125mm ducting flange (B) No 1 Canopy (C) No 2 Recirculation grilles (G) No 1 Lower chimney stack (I) No 1 Recirculation ducting (P) No 2 Recirculation extension ducts (P1) No 1 Recirculation spigot (R)...

Page 12 - CLEARANCE HEIGHTS

INSTALLING THE CHIMNEY HOOD CLEARANCE HEIGHTS The chimney hood is designed to be fittedover a cooking appliance. A minimum clear-ance height of 650mm (25˚ins) is requiredwhen installed above a built-in electric hob,or 700mm (27˚ins) when installed above abuilt-in gas hob. When installed between adjo...

Page 13 - FIXING THE CANOPY

INSTALLING THE CHIMNEY HOOD 4. Drill the holes for the fixing screwsusing an 8mm masonry drill bit. Insertthe rawl plugs and fix the brackets (2)u s i n g t h e 4 . 2 x 4 4 . 4 m m s c r e w s provided. DRILLING THE HOLES 1 1. Draw a horizontal line through thevertical 970mm up the wall from the top...

Page 14 - DUCTING; RECIRCULATION

INSTALLING THE CHIMNEY HOOD DUCTING The hood is more effective when used in theextraction mode (ducted to the outside). When used in the extraction mode ensure theducting spigot has been correctly fitted as illustrated. The ducting used must be Æ Æ Æ Æ Æ 125 (5ins) or Æ Æ Æ Æ Æ 150mm (6ins), flexibl...

Page 15 - FITTING THE TELESCOPIC

INSTALLING THE CHIMNEY HOOD by pressing it downwards until the twopieces meet. 3. Connect the two recirculation extensionducting pipes P1 on to the outlets on either side of the spigot R , which push fit into position, by pressing them horzontally until the two pieces meet. 4. Do not fit the recircu...