Rangemaster LEIHDC60BC - Manuals

Page 2 - This booklet applies to the models as follows:; CONTENTS

IMPORTANT SAFETY INFORMATION Installation Page 2 Child Safety 2 Maintenance and Service 3 YOUR APPLIANCE 4 OPERATING INSTRUCTIONS Cooker Hood Controls 4 Worktop Lighting 4 Fan 4 To Operate 5 Recirculation 5 Extraction 5 MAINTENANCE AND CLEANING Cleaning 6 Metal Grease Filters 6 Charcoal Filters 7 To...

Page 3 - INSTALLATION; IMPORTANT SAFETY INFORMATION; CHILD SAFETY; DURING USE

• INSTALLATION • Any installation work must be underakenby a qualified electrician or a competentperson. • T h i s h o o d m u s t b e i n s t a l l e d i na c c o r d a n c e w i t h t h e i n s t a l l a t i o ninstructions and all measurements mustbe adhered to. • If the cooker hood is installed ...

Page 4 - MAINTENANCE AND SERVICE

• MAINTENANCE AND SERVICE • This appliance can be a hazard if thegrease filters and charcoal filters are notcleaned and replaced as recommended. • Always insist on genuine RANGEmasterspare parts. • U n d e r n o c i r c u m s t a n c e s s h o u l d y o uattempt to repair the appliance yourself.Repa...

Page 5 - COOKER HOOD CONTROLS; OPERATING INSTRUCTIONS; FAN

The chimney hood is designed to extractunpleasant odours from the kitchen, it will notextract steam. The appliance can be installed to recirculate or extract contaminated air. COOKER HOOD CONTROLS The chimney hood functions are controlledby three manual slide switches located on the right, on the un...

Page 6 - TO OPERATE; RECIRCULATION; EXTRACTION

TO OPERATE Select the required fan speed and light if required. RECIRCULATION In the recirculation mode contaminated airenters the chimney hood through the greasefilter cassettes. The air is cleaned by thecharcoal filters and leaves through the grilles in either side of the chimney stack. EXTRACTION...

Page 7 - CLEANING; bright metal finishes.; METAL GREASE FILTERS; MAINTENANCE AND CLEANING

B e f o r e c a r r y i n g o u t a n y maintenance or cleaning isolate thec o o k e r h o o d f r o m t h e m a i n s supply. CLEANING We recommend the chimney hood is cleanedusing a damp cloth wrung out in warm soapy water using a mild liquid household cleaner. Never use excessive amounts ofwater ...

Page 8 - replaced as recommended.; LIGHTING

CHARCOAL FILTERS (2) I n t h e r e c i r u l a t i o n m o d e t h e a c t i v a t e dcharcoal filters absorb smells and unwantedodours. The charcoal filters cannot be cleaned orregenerated and must be replaced every fourmonths, or more frequently if the hood is usedconsistently over 4 hours per day...

Page 9 - TECHNICAL INFORMATION; DIMENSIONS; INSTALLATION INSTRUCTIONS

TECHNICAL INFORMATION DIMENSIONS CANOPY: Height 240mm Width (60cm version) 598mm (90cm version) 898mm (120cm version) 1198mm Depth 490mm CHIMNEY: Height (Upper Section) 415mm (Lower Section) 560mm ELECTRICAL SUPPLY VOLTAGE: (50Hz) 230V POWER CONSUMPTION: 225W FAN MOTOR: 145W LIGHT BULB: 2 x 40W 80W ...

Page 10 - ELECTRICAL CONNECTION; THIS APPLIANCE MUST BE EARTHED; ELECTRICAL REQUIREMENTS

ELECTRICAL CONNECTION THIS APPLIANCE MUST BE EARTHED ELECTRICAL REQUIREMENTS Any permanent electrical installation mustcomply with the latest I.E.E. Regulations andlocal Electricity Board regulations. For yourown safety this should be undertaken by aqualified electrician e.g. your local ElectricityB...

Page 11 - INSTALLATION REQUIREMENTS; INSTALLING THE CHIMNEY HOOD; UNPACKING; The cooker hood is supplied with the

INSTALLATION REQUIREMENTS Please ensure that when the appliance isinstalled it is easily accessible to an engineer in the event of a breakdown. All installations must comply withthe local authorities requirementsfor the discharge of exhaust air. Incorrect installation may affect thesafety of this co...

Page 12 - CLEARANCE HEIGHTS; appliance with a high level grill.

INSTALLING THE CHIMNEY HOOD CLEARANCE HEIGHTS The chimney hood is designed to be fittedo v e r a c o o k i n g a p p l i a n c e . A m i n i m u mc l e a r a n c e h e i g h t o f 6 5 0 m m ( 2 5 ˚ i n s ) i srequired when installed above a built-ine l e c t r i c h o b , o r 7 0 0 m m ( 2 7 ˚ i n s...

Page 13 - DUCTING

Note: If the hood is to be installed onto ahollow construction or plaster or partitionboard wall then special fixing screws will be required (not supplied). F I T T I N G T H E C A N O P YHOOD 1. Rotate the adjusting screws (R) on thecanopy (C) to about halfway. 2. Hook the canopy (C), onto the wall...

Page 14 - screws provided in the fixing kit.

RECIRCULATION If you are using the hood for recirculation,ensure the charcoal filters are in positionfollowing the instructions contained in thesection “To Remove/Replace the CharcoalFilters”. N o t e : W h e n t h e h o o d i s u s e d i n t h erecirculation mode ensure that the plate(T) has been f...

Page 15 - FITTING THE FRONT RAIL; NB When fitted the rail should be below

INSTALLING THE CHIMNEY HOOD FITTING THE FRONT RAIL These instructions apply to models asfollows: - CLAHDC60BB/ CLAHDC90BB/, CLAHDC90BC/ CLAHDC120BB/, CLAHDC120BC/ Do not fit the front rail until the chimneyhood is mounted on the wall. 1. Use a 4mm Allen key to fix themounting brackets to the front o...