Polaris Trail Touring - Manuals

5 INTRODUCTION Preservation of the Environment Polaris is committed to supporting an environmental education cam- paign. We encourage governments to adopt rigorous safety training pro- grams that encourage protection of our environment, including wildlife and vegetation.Snowmobile clubs and other or...

6 SAFETY Operator Safety The following signal words and symbols appear throughout this manual and on your vehicle. Your safety is involved when these words and sym- bols are used. Become familiar with their meanings before reading the manual. The safety alert symbol , on your vehicle or in this manu...

7 SAFETY Operator Safety Follow the recommended maintenance program beginning on page 70 of this manual to ensure that all critical components on the snowmobile are thoroughly inspected by your dealer at specific mileage intervals. Driving a snowmobile requires your full attention. DO NOT drink alco...

8 SAFETY Operator Safety Stay Clear of Track Your snowmobile is propelled by a revolving track that must be partially exposed for proper operation. WARNING! Serious injuries may result if hands, feet, or clothing become entangled in the track. Be alert when riding, and remain properly seated to stay...

9 SAFETY Operator Safety Riding Apparel Be prepared, be warm and be com- fortable when riding. Be aware of the weather forecast, especially the wind- chill, and dress accordingly. See the chart on page 21. WARNING! Avoid wearing loose clothing or long scarves, which can become entangled in moving pa...

10 SAFETY Operator Safety Riding Position Operating a snowmobile requires skill and balance for proper control. Rider positions may vary with experience and the features available on some snowmobiles, but under many conditions, the proper position is to be seated with both feet on the running boards...

11 SAFETY Operator Safety Disabled Operators Safe operation of this rider-active vehicle requires good judgement and physical skills. Operators with cognitive or physical disabilities have an increased risk of loss of control, which could result in serious injury or death. Cargo Overload Too much we...

12 SAFETY Excessive Speed Always observe all laws governing snowmobile operation and speed limits. Always be alert and pay attention to the trail ahead. Multiplying speed (MPH) by 1.5 will equal the approximate number of feet per sec- ond your machine travels. If your speed is 40 MPH, your machine i...

13 SAFETY Operator Safety Driver Awareness Slow down when traveling near poles, posts, or other obstacles. Be especially alert if you're snowmobiling after dark. Always be on the alert for wire fences. Single strands are especially dangerous, since there may be a great distance between posts. Guy wi...

14 SAFETY Operator Safety Avalanches Snowmobilers should always be properly trained and equipped before traveling in mountainous terrain:• Take an avalanche class• Travel with experienced people• Travel on designated trails• Make sure each person is equipped with a shovel, probe and avalanche beacon...

15 SAFETY Operator Safety Ice and Snow Build-up Before driving, manually turn the skis to the left and right to be sure ice and snow are not interfering with full left and right steering. If difficulty is encountered, remove ice and snow build-up that may be obstructing the steering linkage. WARNING...

16 SAFETY Operator Safety Driving Downhill When riding downhill, shift your weight to the rear of the machine and reduce your speed to a minimum. Apply just enough throttle to keep the clutch engaged, allowing the engine's compression to help slow the machine and keep it from rolling freely downhill...

17 SAFETY Operator Safety Driving in Hilly Terrain WARNING! Climbing a hill or crossing the face of a slope may result in loss of balance and machine roll-over, causing serious injury or death. Use caution and good judgement when driving in hilly terrain. Use extra caution when operating in hilly te...

18 SAFETY Operator Safety Clutch Guard Do not operate the engine with the clutch guard removed. The clutch guard is designed to protect the operator from metal parts if the clutch should fail. Although the chance of failure is extremely remote, don't defeat the purpose of the safety guard by removin...

19 SAFETY Operator Safety Inadequate Snow Conditions Moveable hood closures are included on some Polaris snowmobiles. They are normally left open and are located on the front upper and lower hood openings. If operating in deep snow or in extreme cold conditions (below -20 _ F), Polaris recommends cl...

20 SAFETY Operator Safety Driving Responsibly Every snowmobile handles differently, and even the most docile condi- tions may become dangerous if operators drive improperly. If you're new to snowmobiling, acquaint yourself with the machine and with what it will and won't do under various conditions....

21 SAFETY Operator Safety Windchill/Temperature Charts The following information is provided to help you determine when tem- peratures become dangerous for riding. WINDCHILL CHART ( _ F) WINDCHILL CHART ( _ C) Wind Speed in MPH Actual Thermometer Reading ( _ F) 40 35 30 25 20 15 10 5 0 -5 -10 -15 -2...

22 SAFETY Safety Decals and Locations Warning decals have been placed on the snowmobile for your protec- tion. Read and follow the instructions of the decals and other warnings on the snowmobile carefully. If any of the decals depicted in this manual differ from the decals on your snowmobile, always...

23 SAFETY Safety Decals and Locations Track Warning The track warning decal is on the rear of the tunnel: WARNING Stay clear of track. Do not sit on seat back. Entanglement with the track or a fall from seat back can result in severe injury or death. Passenger Warning Polaris touring models are desi...

24 SAFETY Safety Decals and Locations Electronic Reverse Warning Polaris snowmobiles equipped with electronic reverse have a reverse warning decal on the lower dash: WARNING Reverse operation, even at low speeds, can cause loss of con- trol resulting in serious injury or death. To avoid loss of con-...

25 SAFETY Safety Decals and Locations Operation Warning The operation warning decal is located on the console: WARNING • To avoid serious injury or death, read and understand all warnings and the Owner's Manual before operation. If manual is missing, con- tact a Polaris dealer for a replacement. • T...

26 FEATURES Some Polaris snowmobiles are equipped with special features. Operat- ing controls and special feature controls are illustrated on this page. Not all models come with all special features. See your Owner's Manual Supplement. 1. Fuel Filler Cap2. Ignition Switch3. Brake Lever4. Speedometer...

28 FEATURES Backrest The backrest is adjustable for either operator or passenger use.1. Loosen the upper adjustment knobs to raise or lower the backrest. 2. Loosen the lower adjustment knobs to move the backrest forward for operator use or rearward for passenger use. 3. Always tighten the knobs secu...

29 THE PERFECT FIT Front Suspension Adjustments Independent Front Suspension (IFS) Break in the suspension for about 150 miles (240 km) before making any fine-tuning adjustments. Settings will vary from rider to rider, depending on rider weight, vehicle speed, riding style, and trail conditions. We ...

30 THE PERFECT FIT Front Suspension Adjustments WARNING! Improper ski alignment or adjustment may cause loss of steering control, resulting in serious injury or death. Always verify ski alignment before making adjustments to the IFS. See page 100 to check alignment. Do not attempt to change the ski ...

31 THE PERFECT FIT Front Suspension Adjustments Spring Preload Increasing spring preload will increase ski-to-ground pressure. Decreasing spring preload will decrease ski-to- ground pressure. When adjusting, be sure the springs on both the left and right sides of the machine are at the same adjustme...

32 THE PERFECT FIT Rear Suspension Adjustments Rider weight, riding style, trail conditions, and vehicle speed all affect suspension action.Each rear suspension can be adjusted to suit rider preference and deliver excellent performance for a given set of conditions. However, all sus- pension designs...

33 THE PERFECT FIT Rear Suspension Adjustments Suspension Performance Tips • Rider weight usually determines the position at which the spring pre- load should be set. However, this may vary with riding style. With a little experimentation, each rider can find a preferred setup. These adjustments are...

34 THE PERFECT FIT EDGE 136 Rear Suspension Adjustments Initial Spring Preload Setting (Sag Method) To set up the EDGE rear suspension torsion spring preload, measure the distance between the ground and rear bumper. This is measurement X.Take the first measurement with no rider and with the rear sus...

35 THE PERFECT FIT EDGE 136 Rear Suspension Adjustments Rear Spring Tension To adjust rear torsion spring tension, rotate the three-position cam using the engine spark plug tool. Different rate torsion springs are available if a firmer ride is desired. See your dealer for more information.The follow...

36 THE PERFECT FIT EDGE 136 Rear Suspension Adjustments Indy Select Rear Shock Some snowmobiles are equipped with the Indy Select rear shock, which allows for adjustments to the compression valving. Locate the adjust- ment screw near the base of the shock. In half-turn increments, turn the screw clo...

37 THE PERFECT FIT EDGE 136 Rear Suspension Adjustments Optional Torsion Springs Different rate torsion springs are available for some shocks if a firmer ride is desired. Contact your dealer for more information. Suspension Coupling On all Polaris snowmobile rear suspensions, there are two torque ar...

38 THE PERFECT FIT EDGE 136 Rear Suspension Adjustments Suspension Coupling Rear To Front Coupling and the Rear Rear Scissor Stop (RRSS) The rear rear scissor stop (RRSS) couples the movement of the rear torque arm with the front torque arm and limits the amount of indepen- dent movement between the...

39 THE PERFECT FIT EDGE 136 Rear Suspension Adjustments Weight Transfer During Acceleration The preferred method for controlling weight transfer during acceleration is by adjusting the rear rear scissor stop (RRSS). The factory setting is the best for most trail riding condi- tions.To decrease weigh...

40 THE PERFECT FIT Handlebar Adjustment Follow these steps to adjust handlebar angle at the handlebar block.1. Remove the handlebar cover to expose the handlebar and the four adjuster block bolts. 2. Using a 7/16-inch wrench, loosen the four nuts on the bottom of the adjuster block (turn the handleb...

41 THE PERFECT FIT Traction Products Studs Before equipping your machine with traction products, be aware of the laws in your area pertaining to the use of traction products. See your dealer about installing studs and/or carbides. Many tracks with deep lug designs cannot be studded, but your dealer ...

42 THE PERFECT FIT Traction Products n Carbide Skags A skag is a replaceable bar attached to the underside of the ski to assist in turning the snowmobile and to prevent ski wear caused by contact with roads and other bare terrain. Use carbide skags with studded tracks to help maintain proper vehicle...

43 THE PERFECT FIT Traction Products Wear Strips To avoid excessive tunnel wear, tunnel wear strips must be installed whenever track studding is used. See your dealer for more information.Wear strips are designed for a specific stud length. See your dealer's studding chart for recommended traction a...

44 THE PERFECT FIT Accessories Polaris offers a wide range of accessories for your snowmobile to help make each ride more enjoyable.Use only Polaris parts and accessories on your Polaris snowmobile. Use of unapproved parts and accessories may result in:• Non-compliance with government/industry requi...

45 PRE-RIDE INSPECTIONS Pre-Ride Checklist Inspect all items on the checklist for proper operation or condition before each use of the snowmobile. Procedures are outlined on the refer- enced pages. Look for a checkmark ( n ) on the referenced pages to locate the pre-ride inspection items. Item See P...

46 PRE-RIDE INSPECTIONS Before Starting the Engine Before starting the engine, always refer to all safety warnings pertaining to snowmobile operation. Never start the engine without checking all vehicle components to be sure of proper operation. WARNING! Operating the vehicle with worn, damaged, or ...

47 PRE-RIDE INSPECTIONS Before Starting the Engine n Hydraulic Brakes Always check the following items for proper operation before starting the engine. Brake Lever Travel Squeeze the brake lever. It should move no closer to the handgrip than 1/2 I (1.3 cm). A smaller distance indicates low brake flu...

48 PRE-RIDE INSPECTIONS Before Starting the Engine n Parking Brake Lever Lock Your snowmobile may have a parking brake lever lock located over the brake lever. Use the brake lever lock only when you want the machine to remain sta- tionary; for example, when parked on an incline for a period of five ...

49 PRE-RIDE INSPECTIONS Before Starting the Engine n Steering System WARNING! Ice and snow build-up may interfere with the steering of your machine, resulting in serious injury or death. Keep the underhood area free of snow and ice. Before driving, manually turn the skis to the left and right to be ...

50 PRE-RIDE INSPECTIONS Before Starting the Engine n Hood Latches The hood of the snowmobile protects the operator from moving parts as well as aiding in sound emission control and other functions. Under no circumstances should your snowmobile be operated with the hood open or removed. Always ensure...

51 PRE-RIDE INSPECTIONS Start the Engine and Check n Engine Stop Switch Check the auxiliary shut-off switch for proper operation. Push the switch down to stop the engine. Pull it up to allow restarting. n Ignition Switch Make sure the engine stops when the ignition switch is turned to OFF. n Lightin...

52 OPERATION Starting the Engine NOTICE: Engaging the starter when the engine is running WILL result in serious engine damage, especially if the transmission is in reverse. Never engage the starter when the engine is running. 1. Turn the fuel valve on. See page 57. 2. Turn the key to the ON position...

53 OPERATION Engine Break-In No single action on your part is as important to long, trouble-free machine life as proper break-in of a new or rebuilt engine. Premix the first tank of fuel with one pint of Polaris injection oil for each five gal- lons of fuel. This, in addition to the lubrication supp...

54 OPERATION Engine Break-In Oil Injection System Always check and fill the oil tank when refueling. See page 59. NOTICE: Serious engine damage can occur without the proper lubrication. Check the oil tank level often during the first tank of fuel. If the oil level doesn't go down, contact your deale...

55 OPERATION Track Warm-Up WARNING! Use of traction products such as studs, ice growsers, etc. will increase the possibility of track damage and/or failure. This could cause loss of control, resulting in serious injury or death. Always inspect for track damage before operating the snowmobile. Follow...

56 OPERATION Slide Rail and Track Cooling NOTICE: Inadequate cooling and lubrication will lead to overheating of the slide rail and track, resulting in premature wear and failure. Reduce speeds and frequently drive into fresh snow to allow adequate cooling and polishing of the slide rail and track s...

57 OPERATION Fuel Fuel Valve Turn the fuel valve clockwise to OFF to shut off the fuel supply. Turn the valve counter-clockwise to ON to turn the fuel supply on. Fuel Recommendations Your Polaris engine is designed to run on 87 octane non-oxygenated or 89 octane oxygenated pump gasoline. There's a g...

58 OPERATION Fuel Fuel Reserve Capacity (Mechanical Gauge) There are approximately two gallons of fuel left in the tank when the mechanical fuel gauge reads RES. Fuel System Deicers If you use non-oxygenated fuel, Polaris recommends the regular use of isopropyl-based fuel system deicer. Add one to t...

59 OPERATION n Oil Low Oil Indicator Light The low oil indicator light will alert the operator if the oil level is low. Visually check for oil in the bottle. If oil is not visible, continued opera- tion may cause serious engine damage. Add oil before further operation of the snowmobile. Low Oil Leve...

60 OPERATION Carburetion Proper carburetor adjustment is critical. Always have your Polaris dealer perform any carburetor adjustments.A lean mixture (too much air, too little fuel) may result in piston burn- ing, bearing failure, or complete engine failure. A rich mixture (too much fuel, too little ...

61 OPERATION Carburetion Jetting Guidelines Changes in altitude and temperature affect air density, which is the amount of oxygen available for combustion. In low elevations and cold temperatures, the air has more oxygen. In higher elevations and higher temperatures, the air is less dense.The carbur...

62 OPERATION n Engine Stop Switch Push down on the engine stop switch ( + ) to ground out the ignition and stop the engine quickly. Pull the switch up to the ON position to allow restarting. n Throttle Safety Switch The throttle safety switch is designed to stop the engine whenever all pressure is r...

64 OPERATION Emergency Stopping The following chart lists methods for stopping the snowmobile in the event of an emergency. See page 62 for more information about the engine stop switch and throttle safety switch. WARNING! Excessive or repetitive use of brakes for high speed stops will cause an over...

65 OPERATION Electronic Reverse (PERC t ) Electronic reverse will activate only if the engine RPM is below 4000. If your machine is running at an altitude of over 6000 feet, adjust the igni- tion setting as described on page 67. Always make sure the vehicle is stopped and the engine is running at id...

66 OPERATION Electronic Reverse (PERC t ) Engaging Reverse 1. Stop the snowmobile and leave the engine idling.2. Make sure the area behind your vehicle is clear.3. Push the yellow reverse but- ton ( + ) on the left-hand con- trol for one second, then release. The engine will auto- matically reduce R...

67 OPERATION Electronic Reverse (PERC t ) Disengaging Reverse 1. Stop the snowmobile and leave the engine idling. NOTICE: Engaging the starter when the engine is running WILL result in serious engine damage, especially if the transmission is in reverse. Never engage the starter when the engine is ru...

68 OPERATION Towing Do not use the front bumper to pull or drag the snowmobile. The front bumper is not designed for this type of use and may detach from the vehicle if force is applied.For your safety, do not attempt to use a tow hitch until you've read the following warnings and understand the pro...

69 MAINTENANCE Emission Control Information Any qualified repair shop or qualified person may maintain, replace, or repair the emission control devices or systems on your snowmobile. Emission Control Label Your snowmobile is equipped at the time of sale with an emission con- trol information (ECI) l...

70 MAINTENANCE Polaris Recommended Maintenance Program To ensure many trouble-free miles of snowmobiling enjoyment, follow recommended regular maintenance and perform service checks as out- lined in this manual. Record maintenance and service in the Mainte- nance Log beginning on page 128.The recomm...

71 MAINTENANCE Periodic Maintenance Interval Table The following chart is a guide based on average riding conditions. You may need to increase frequency based on riding conditions. When inspection reveals the need for replacement parts, always use genuine Polaris parts, available from your Polaris d...

74 MAINTENANCE Lubrication Suspension and Steering Lubricate the suspension and steering components with Polaris Pre- mium All-Season Grease at 500 miles (800 km) and annually or every 1000 miles (1600 km) thereafter. See page 111 for the part numbers of Polaris products.The illustration shows the l...

75 MAINTENANCE Lubrication EDGE 136 Rear Suspension Driveshaft Bearing Inject grease into the fitting on the speed- ometer sensor housing until grease purges from the seal on the inside of the tunnel. This should take approximately two pumps. Do not use more than four pumps. Throttle Cable Lubricate...

76 MAINTENANCE Lubrication n Chaincase Oil Check the chaincase oil level at the intervals outlined in the mainte- nance charts beginning on page 70. Change the chaincase oil after the first 500 miles (800 km), then every 1000 miles (1600 km) or season- ally.Maintain the oil level between the “safe” ...

77 MAINTENANCE Spark Plugs It’s very important to use the correct spark plug for your machine. A spark plug with a heat range too high will cause engine damage. A spark plug with a heat range too low will cause excessive fouling and engine malfunctioning. NOTICE: A spark plug with a heat range too h...

78 MAINTENANCE Spark Plugs Normal Plug The normal insulator tip is gray, tan or light brown. There will be few combustion deposits. The electrodes are not burned or eroded. This indi- cates the proper type and heat range for the engine and the service.The tip should not be white. A white insulator t...

79 MAINTENANCE Intake Filters The intake foam filter ( + ) limits snow ingestion into the intake system. When operating in loose powder snow, check the top of the foam filter periodically to remove any accumulation of snow. NOTICE: Operating the snowmobile with the intake filters removed may cause c...

80 MAINTENANCE Fuel Filter/Fuel Lines The fuel filter is located inside the fuel tank. This component requires no maintenance.Inspect the fuel lines regularly for signs of deterioration or damage. Always check fuel line condition after periods of storage. Normal dete- rioration from weather and fuel...

81 MAINTENANCE Carburetor The number stamped in the end of the main jet indicates the jet size. The jet installed at the time of manufacture is not necessarily correct for your elevation. It's your dealer's responsibility to make sure the correct main jet is installed. NOTICE: Operating the snowmobi...

82 MAINTENANCE Carburetor Water/Sediment Trap Service Most Polaris snowmobiles contain patented carburetor bowl water/sedi- ment traps located at the bottom of each carburetor. The trap, consisting of a hose with a plug, should be drained at least every 2000 miles (3200 km) and inspected for contami...

83 MAINTENANCE Exhaust System Check the exhaust system for wear or damage at approximately 2000 miles (3200 km). To inspect, allow the engine and exhaust system to cool completely. Open the hood and inspect the muffler and pipes for cracks or damage. Check for weak or missing retaining springs or da...

84 MAINTENANCE Brakes n Hydraulic Brake Inspection Inspect the brake lever reserve before each use of the snowmobile. See page 47.Brake pads must be replaced when the brake pad material becomes thin- ner than the backing plate (approximately 1/16 inch/1.5 mm). A kit is available for replacing brake ...

85 MAINTENANCE Brakes Brake Fluid WARNING! After opening a bottle of brake fluid, always discard any unused portion. Never store or use a partial bottle. Brake fluid is hygroscopic, meaning it rapidly absorbs moisture from the air. The moisture causes the boiling temperature of the brake fluid to dr...

86 MAINTENANCE Brakes Bleeding the Hydraulic Brake System Air in the hydraulic brake system will cause spongy brake lever action. Bleed the system before operating the snowmobile. WARNING! Operating the vehicle with a spongy brake lever can result in loss of brakes, which could cause an accident and...

87 MAINTENANCE Lights Headlight Adjustment The headlight may be adjusted for vertical aim using the following pro- cedure.1. Place the snowmobile on a level surface with the headlight approxi- mately 25 feet (7.6 m) from a wall. 2. Measure the distance from the floor to the center of the headlight a...

88 MAINTENANCE Lights NOTICE: Do not touch a halogen bulb with bare fingers. Oil from skin leaves a residue, causing a hot spot that will shorten the life of the lamp. If fin- gers do touch the bulb, clean it with an alcohol-moistened towel. Headlight Bulb Replacement 1. Pinch the ends of the spring...

89 MAINTENANCE Clutch System Periodically inspect clutch sheaves for damage, wear or belt residue. To maintain optimum performance, clean with non-oil based cleaners such as isopropyl alcohol. NOTICE: If you become aware of higher than normal clutch engagement or an unusual vibration or shift patter...

90 MAINTENANCE Clutch System Drive Belt Removal 1. Stop the engine after operating in a forward motion. NOTICE: Do not attempt to remove the drive belt after operating in reverse. The snowmobile must be stopped after forward motion to prevent damage to components during belt removal. 2. Turn the ign...

91 MAINTENANCE Clutch System Drive Belt Installation 1. Drop the drive belt over the drive clutch and pull back the slack. Tip: To ensure satisfactory belt life, install belts so they operate in the same direction of rotation by positioning the identification numbers so that you can read them. If re...

92 MAINTENANCE Clutch System n Drive Belt Deflection Measure belt deflection with both clutches at rest and in their full neutral position.Place a straight edge (1) on the belt and apply downward pressure while measuring at point 2. This measurement should be 1 1/4 inches (32 mm). Drive Belt Adjustm...

93 MAINTENANCE Clutch System Torque Stop If your snowmobile is equipped with an engine torque stop, periodically check torque stop clearance.With clutches in proper alignment, the torque stop clearance should be .010- .030 inch (.25-.75 mm) from the engine case.Adjust if necessary, and lock the jam ...

94 MAINTENANCE Chain Tension Maintain the proper chain tension as outlined on page 83. Fall Tune-Up For maximum performance, arrange for a fall service tune-up with your Polaris dealer. His experienced and trained service technician will keep your machine in peak operating condition. Tool Kit A tool...

95 MAINTENANCE Track Track Inspection WARNING! Broken track rods can cause a rotating track to come off the machine, which could cause serious injury or death. Never operate with a damaged track. Never rotate a damaged track under power. 1. Using a hoist, safely lift and support the rear of the snow...

96 MAINTENANCE Track Moving parts can cut and crush body parts. When performing the checks and adjustments recommended on the following pages, stay clear of all moving parts. Never perform track measurement or adjustments with the engine run- ning. Track Tension Track adjustment is critical for prop...

97 MAINTENANCE Track Track Tension If the track needs adjustment: 6. Loosen the rear idler shaft bolts. 7. Loosen the locknuts. 8. Tighten or loosen the track adjusting screws to provide equal adjustment on both sides of the track. 9. Repeat the measure- ment on the other side of the track. Tip: Che...

98 MAINTENANCE Track n Track Alignment Periodically check that the track is centered and running evenly on the slide rails. Misalignment will cause excessive wear to the track and slide rail.1. Safely support the rear of the machine with the track off the ground.2. Start the engine and apply a small...

99 MAINTENANCE Steering System n Rail Slide Wear For ease of inspection, all Polaris rail slides have a wear limit indicator groove to indicate the minimum permissible slide thickness. Replace the rail slides if they are worn to the top of the groove at any point along their length. Failure to do so...

100 MAINTENANCE Steering System Ski Alignment WARNING! Improper ski alignment or adjustment may cause loss of steering control, resulting in serious injury or death. Do not attempt to change the ski alignment or camber adjustment. See your Polaris dealer. With the handlebars in a straight ahead posi...

101 MAINTENANCE Steering System n Ski Skags See your dealer's studding chart for recommended skags. If you install longer or more aggressive carbide skags than the original equipment, it may also be necessary to add track studs to maintain proper vehicle con- trol while turning on hard-packed snow o...

102 MAINTENANCE Battery Battery electrolyte is poisonous. It contains acid! Serious burns can result from contact with the skin, eyes, or clothing. If contact occurs, seek immediate medi- cal attention.KEEP OUT OF REACH OF CHILDREN.EXTERNAL: Flush with water.INTERNAL: Drink large quantities of water...

103 MAINTENANCE Battery Battery Removal WARNING! Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death. When removing the battery, always disconnect the negative (black) cable first. When reinstalling the battery, always connect the negati...

104 MAINTENANCE Battery Battery Installation WARNING! Battery electrolyte contains acid. Avoid skin contact with electrolyte as severe burns may result. Using a new battery that has not been fully charged can damage the bat- tery and result in a shorter life. It can also hinder vehicle performance. ...

105 MAINTENANCE Battery Battery Storage When your snowmobile is placed in storage for one month or more:• Remove the battery.• Charge it to the proper level.• Store it in a cool dry place.• Check and/or charge monthly.• Have the battery tested and recharged before reinstalling it in the vehicle. If ...

106 MAINTENANCE n Pre-Ride Suspension Inspection Loose nuts and bolts can reduce your snowmobile's reliability and cause needless repairs and down time. Before beginning any snowmobile trip, a visual inspection will uncover potential problems. Check the follow- ing items on a weekly basis or before ...

107 MAINTENANCE Extended Storage Off-season or extended storage of your snowmobile requires preventive measures to aid against deterioration and to prolong the useful life of many components. See page 111 for the part numbers of Polaris prod- ucts. Cleaning and Preservation Proper storage starts wit...

108 MAINTENANCE Extended Storage Bearings Grease the drive shaft clutch side bearing with Polaris Premium All- Season Grease or a similar high quality grease to prevent corrosion. Clutch and Drive System Remove the drive belt and store in a cool dry location. To prevent oxida- tion on the clutch she...

110 MAINTENANCE Extended Storage Electrical Connections Separate electrical connector blocks and clean corrosive build-up from connectors. Lubricate or pack connector blocks with dielectric grease and re-connect. Replace worn or frayed electrical wire and connectors. Be sure wiring harness is proper...

111 POLARIS PRODUCTS Part No. Description Engine Lubricants 2870791 Fogging Oil (12 oz. Aerosol) 2871098 Premium 2-Cycle Engine Oil (qt.) 2871097 Premium 2-Cycle Engine Oil (gal.) 2871240 Premium 2-Cycle Engine Oil (2.5 gal.) 2871721 Premium Gold Synthetic 2-Cycle Engine Oil (qt.) 2871722 Premium Go...

112 TROUBLESHOOTING Engine Troubleshooting Unless you have experience and training in two-cycle engine repair, see your dealer if technical problems arise. Problem Probable Cause Solution Erratic engine oper- ating RPM during acceleration or load variations Drive clutch binding • Disassemble drive c...

116 TROUBLESHOOTING Drive Belt Troubleshooting Belt Wear/Burn Diagnosis Causes Solutions Driving at low RPM • Drive at higher RPMs. Gear the machine down. Check belt deflection. Insufficient warm-up • Warm the engine at least five minutes. Take the drive belt off the machine in extremely cold weathe...

117 WARRANTY Service and Warranty Information Obtaining Service and Warranty Assistance Read and understand the service data and the Polaris warranty informa- tion contained in this manual. Contact your Polaris dealer for replace- ment parts, service or warranty. Your dealer receives frequent update...

118 WARRANTY Service and Warranty Information Polaris Anti-Theft System The Polaris anti-theft system (PATS) monitoring program is designed to aid owners of registered snowmobiles in recovery of stolen machines. Administration 1. Polaris snowmobile owner reports theft. A. In addition to notifying th...

119 WARRANTY Limited Warranty Polaris Sales Inc., 2100 Highway 55, Medina, MN 55340, provides a ONE YEAR LIM- ITED WARRANTY on all components of the Polaris snowmobile against defects in material or workmanship. This warranty covers the parts and labor charges for repair or replacement of defective ...

121 WARRANTY Conditions and Exclusions In order to qualify for warranty, the product must have been properly set up and tested by a Polaris Dealer (if applicable). Failure of any dealer to perform the required vehicle Pre-Delivery Inspection, perform all applicable service bulletins and have the con...

122 WARRANTY Polaris Second Year Engine Service Contract Second Year Engine Service Contract is standard on all eligible new and unused snow- mobiles that were Snow Checked through an authorized Polaris dealer during the March/April Snow Check promotion. The free Second Year Engine Service Contract ...

123 WARRANTY Polaris Second Year Engine Service Contract Coverage Coverage for second year engine failures due to defects in materials and workmanship will be determined by Polaris in its sole discretion. Coverage is automatic with no addi- tional paperwork required. The free Second Year Engine Serv...

124 WARRANTY Exported Vehicles EXCEPT WHERE SPECIFICALLY REQUIRED BY LAW, THERE IS NO WAR- RANTY OR SERVICE BULLETIN COVERAGE ON THIS VEHICLE IF IT IS SOLD OUTSIDE THE COUNTRY OF THE SELLING DEALER'S AUTHORIZED LOCA- TION.This policy does not apply to vehicles that have received authorization for ex...

125 WARRANTY Exported Vehicles How to Get Service In the Country where your vehicle was purchased: Warranty or Service Bulletin repairs must be done by an authorized Polaris dealer. If you move or are traveling within the country where your vehicle was purchased, Warranty or Service Bulletin repairs...

128 MAINTENANCE LOG Present this section of your manual to your dealer each time your snow- mobile is serviced. This will provide you and future owners with an accurate log of maintenance and services performed on the snowmobile. DATE MILES (KM) TECHNICIAN SERVICE PERFORMED / COMMENTS 150 mi. (240 k...

132 INDEX A Accessories . . . . . . . . . . . . . . . . . . . 44 Air Box Warning . . . . . . . . . . . . . . . 22 Air Pollution . . . . . . . . . . . . . . . . . . . 5 Altitude Setting . . . . . . . . . . . . . . . . 67 Avalanches. . . . . . . . . . . . . . . . . . . . 14 B Backrest . . . . . . . . ...

5 INTRODUCTION Preservation of the Environment Polaris is committed to supporting an environmental education cam- paign. We encourage governments to adopt rigorous safety training pro- grams that encourage protection of our environment, including wildlife and vegetation.Snowmobile clubs and other or...

6 SAFETY Operator Safety The following signal words and symbols appear throughout this manual and on your vehicle. Your safety is involved when these words and sym- bols are used. Become familiar with their meanings before reading the manual. The safety alert symbol , on your vehicle or in this manu...

7 SAFETY Operator Safety Follow the recommended maintenance program beginning on page 70 of this manual to ensure that all critical components on the snowmobile are thoroughly inspected by your dealer at specific mileage intervals. Driving a snowmobile requires your full attention. DO NOT drink alco...

8 SAFETY Operator Safety Stay Clear of Track Your snowmobile is propelled by a revolving track that must be partially exposed for proper operation. WARNING! Serious injuries may result if hands, feet, or clothing become entangled in the track. Be alert when riding, and remain properly seated to stay...

9 SAFETY Operator Safety Riding Apparel Be prepared, be warm and be com- fortable when riding. Be aware of the weather forecast, especially the wind- chill, and dress accordingly. See the chart on page 21. WARNING! Avoid wearing loose clothing or long scarves, which can become entangled in moving pa...

10 SAFETY Operator Safety Riding Position Operating a snowmobile requires skill and balance for proper control. Rider positions may vary with experience and the features available on some snowmobiles, but under many conditions, the proper position is to be seated with both feet on the running boards...

11 SAFETY Operator Safety Disabled Operators Safe operation of this rider-active vehicle requires good judgement and physical skills. Operators with cognitive or physical disabilities have an increased risk of loss of control, which could result in serious injury or death. Cargo Overload Too much we...

12 SAFETY Excessive Speed Always observe all laws governing snowmobile operation and speed limits. Always be alert and pay attention to the trail ahead. Multiplying speed (MPH) by 1.5 will equal the approximate number of feet per sec- ond your machine travels. If your speed is 40 MPH, your machine i...

13 SAFETY Operator Safety Driver Awareness Slow down when traveling near poles, posts, or other obstacles. Be especially alert if you're snowmobiling after dark. Always be on the alert for wire fences. Single strands are especially dangerous, since there may be a great distance between posts. Guy wi...

14 SAFETY Operator Safety Avalanches Snowmobilers should always be properly trained and equipped before traveling in mountainous terrain:• Take an avalanche class• Travel with experienced people• Travel on designated trails• Make sure each person is equipped with a shovel, probe and avalanche beacon...

15 SAFETY Operator Safety Ice and Snow Build-up Before driving, manually turn the skis to the left and right to be sure ice and snow are not interfering with full left and right steering. If difficulty is encountered, remove ice and snow build-up that may be obstructing the steering linkage. WARNING...

16 SAFETY Operator Safety Driving Downhill When riding downhill, shift your weight to the rear of the machine and reduce your speed to a minimum. Apply just enough throttle to keep the clutch engaged, allowing the engine's compression to help slow the machine and keep it from rolling freely downhill...

17 SAFETY Operator Safety Driving in Hilly Terrain WARNING! Climbing a hill or crossing the face of a slope may result in loss of balance and machine roll-over, causing serious injury or death. Use caution and good judgement when driving in hilly terrain. Use extra caution when operating in hilly te...

18 SAFETY Operator Safety Clutch Guard Do not operate the engine with the clutch guard removed. The clutch guard is designed to protect the operator from metal parts if the clutch should fail. Although the chance of failure is extremely remote, don't defeat the purpose of the safety guard by removin...

19 SAFETY Operator Safety Inadequate Snow Conditions Moveable hood closures are included on some Polaris snowmobiles. They are normally left open and are located on the front upper and lower hood openings. If operating in deep snow or in extreme cold conditions (below -20 _ F), Polaris recommends cl...

20 SAFETY Operator Safety Driving Responsibly Every snowmobile handles differently, and even the most docile condi- tions may become dangerous if operators drive improperly. If you're new to snowmobiling, acquaint yourself with the machine and with what it will and won't do under various conditions....

21 SAFETY Operator Safety Windchill/Temperature Charts The following information is provided to help you determine when tem- peratures become dangerous for riding. WINDCHILL CHART ( _ F) WINDCHILL CHART ( _ C) Wind Speed in MPH Actual Thermometer Reading ( _ F) 40 35 30 25 20 15 10 5 0 -5 -10 -15 -2...

22 SAFETY Safety Decals and Locations Warning decals have been placed on the snowmobile for your protec- tion. Read and follow the instructions of the decals and other warnings on the snowmobile carefully. If any of the decals depicted in this manual differ from the decals on your snowmobile, always...

23 SAFETY Safety Decals and Locations Track Warning The track warning decal is on the rear of the tunnel: WARNING Stay clear of track. Do not sit on seat back. Entanglement with the track or a fall from seat back can result in severe injury or death. Passenger Warning Polaris touring models are desi...

24 SAFETY Safety Decals and Locations Electronic Reverse Warning Polaris snowmobiles equipped with electronic reverse have a reverse warning decal on the lower dash: WARNING Reverse operation, even at low speeds, can cause loss of con- trol resulting in serious injury or death. To avoid loss of con-...

25 SAFETY Safety Decals and Locations Operation Warning The operation warning decal is located on the console: WARNING • To avoid serious injury or death, read and understand all warnings and the Owner's Manual before operation. If manual is missing, con- tact a Polaris dealer for a replacement. • T...

26 FEATURES Some Polaris snowmobiles are equipped with special features. Operat- ing controls and special feature controls are illustrated on this page. Not all models come with all special features. See your Owner's Manual Supplement. 1. Fuel Filler Cap2. Ignition Switch3. Brake Lever4. Speedometer...

28 FEATURES Backrest The backrest is adjustable for either operator or passenger use.1. Loosen the upper adjustment knobs to raise or lower the backrest. 2. Loosen the lower adjustment knobs to move the backrest forward for operator use or rearward for passenger use. 3. Always tighten the knobs secu...

29 THE PERFECT FIT Front Suspension Adjustments Independent Front Suspension (IFS) Break in the suspension for about 150 miles (240 km) before making any fine-tuning adjustments. Settings will vary from rider to rider, depending on rider weight, vehicle speed, riding style, and trail conditions. We ...

30 THE PERFECT FIT Front Suspension Adjustments WARNING! Improper ski alignment or adjustment may cause loss of steering control, resulting in serious injury or death. Always verify ski alignment before making adjustments to the IFS. See page 100 to check alignment. Do not attempt to change the ski ...

31 THE PERFECT FIT Front Suspension Adjustments Spring Preload Increasing spring preload will increase ski-to-ground pressure. Decreasing spring preload will decrease ski-to- ground pressure. When adjusting, be sure the springs on both the left and right sides of the machine are at the same adjustme...

32 THE PERFECT FIT Rear Suspension Adjustments Rider weight, riding style, trail conditions, and vehicle speed all affect suspension action.Each rear suspension can be adjusted to suit rider preference and deliver excellent performance for a given set of conditions. However, all sus- pension designs...

33 THE PERFECT FIT Rear Suspension Adjustments Suspension Performance Tips • Rider weight usually determines the position at which the spring pre- load should be set. However, this may vary with riding style. With a little experimentation, each rider can find a preferred setup. These adjustments are...

34 THE PERFECT FIT EDGE 136 Rear Suspension Adjustments Initial Spring Preload Setting (Sag Method) To set up the EDGE rear suspension torsion spring preload, measure the distance between the ground and rear bumper. This is measurement X.Take the first measurement with no rider and with the rear sus...

35 THE PERFECT FIT EDGE 136 Rear Suspension Adjustments Rear Spring Tension To adjust rear torsion spring tension, rotate the three-position cam using the engine spark plug tool. Different rate torsion springs are available if a firmer ride is desired. See your dealer for more information.The follow...

36 THE PERFECT FIT EDGE 136 Rear Suspension Adjustments Indy Select Rear Shock Some snowmobiles are equipped with the Indy Select rear shock, which allows for adjustments to the compression valving. Locate the adjust- ment screw near the base of the shock. In half-turn increments, turn the screw clo...

37 THE PERFECT FIT EDGE 136 Rear Suspension Adjustments Optional Torsion Springs Different rate torsion springs are available for some shocks if a firmer ride is desired. Contact your dealer for more information. Suspension Coupling On all Polaris snowmobile rear suspensions, there are two torque ar...

38 THE PERFECT FIT EDGE 136 Rear Suspension Adjustments Suspension Coupling Rear To Front Coupling and the Rear Rear Scissor Stop (RRSS) The rear rear scissor stop (RRSS) couples the movement of the rear torque arm with the front torque arm and limits the amount of indepen- dent movement between the...

39 THE PERFECT FIT EDGE 136 Rear Suspension Adjustments Weight Transfer During Acceleration The preferred method for controlling weight transfer during acceleration is by adjusting the rear rear scissor stop (RRSS). The factory setting is the best for most trail riding condi- tions.To decrease weigh...

40 THE PERFECT FIT Handlebar Adjustment Follow these steps to adjust handlebar angle at the handlebar block.1. Remove the handlebar cover to expose the handlebar and the four adjuster block bolts. 2. Using a 7/16-inch wrench, loosen the four nuts on the bottom of the adjuster block (turn the handleb...

41 THE PERFECT FIT Traction Products Studs Before equipping your machine with traction products, be aware of the laws in your area pertaining to the use of traction products. See your dealer about installing studs and/or carbides. Many tracks with deep lug designs cannot be studded, but your dealer ...

42 THE PERFECT FIT Traction Products n Carbide Skags A skag is a replaceable bar attached to the underside of the ski to assist in turning the snowmobile and to prevent ski wear caused by contact with roads and other bare terrain. Use carbide skags with studded tracks to help maintain proper vehicle...

43 THE PERFECT FIT Traction Products Wear Strips To avoid excessive tunnel wear, tunnel wear strips must be installed whenever track studding is used. See your dealer for more information.Wear strips are designed for a specific stud length. See your dealer's studding chart for recommended traction a...

44 THE PERFECT FIT Accessories Polaris offers a wide range of accessories for your snowmobile to help make each ride more enjoyable.Use only Polaris parts and accessories on your Polaris snowmobile. Use of unapproved parts and accessories may result in:• Non-compliance with government/industry requi...

45 PRE-RIDE INSPECTIONS Pre-Ride Checklist Inspect all items on the checklist for proper operation or condition before each use of the snowmobile. Procedures are outlined on the refer- enced pages. Look for a checkmark ( n ) on the referenced pages to locate the pre-ride inspection items. Item See P...

46 PRE-RIDE INSPECTIONS Before Starting the Engine Before starting the engine, always refer to all safety warnings pertaining to snowmobile operation. Never start the engine without checking all vehicle components to be sure of proper operation. WARNING! Operating the vehicle with worn, damaged, or ...

47 PRE-RIDE INSPECTIONS Before Starting the Engine n Hydraulic Brakes Always check the following items for proper operation before starting the engine. Brake Lever Travel Squeeze the brake lever. It should move no closer to the handgrip than 1/2 I (1.3 cm). A smaller distance indicates low brake flu...

48 PRE-RIDE INSPECTIONS Before Starting the Engine n Parking Brake Lever Lock Your snowmobile may have a parking brake lever lock located over the brake lever. Use the brake lever lock only when you want the machine to remain sta- tionary; for example, when parked on an incline for a period of five ...

49 PRE-RIDE INSPECTIONS Before Starting the Engine n Steering System WARNING! Ice and snow build-up may interfere with the steering of your machine, resulting in serious injury or death. Keep the underhood area free of snow and ice. Before driving, manually turn the skis to the left and right to be ...

50 PRE-RIDE INSPECTIONS Before Starting the Engine n Hood Latches The hood of the snowmobile protects the operator from moving parts as well as aiding in sound emission control and other functions. Under no circumstances should your snowmobile be operated with the hood open or removed. Always ensure...

51 PRE-RIDE INSPECTIONS Start the Engine and Check n Engine Stop Switch Check the auxiliary shut-off switch for proper operation. Push the switch down to stop the engine. Pull it up to allow restarting. n Ignition Switch Make sure the engine stops when the ignition switch is turned to OFF. n Lightin...

52 OPERATION Starting the Engine NOTICE: Engaging the starter when the engine is running WILL result in serious engine damage, especially if the transmission is in reverse. Never engage the starter when the engine is running. 1. Turn the fuel valve on. See page 57. 2. Turn the key to the ON position...

53 OPERATION Engine Break-In No single action on your part is as important to long, trouble-free machine life as proper break-in of a new or rebuilt engine. Premix the first tank of fuel with one pint of Polaris injection oil for each five gal- lons of fuel. This, in addition to the lubrication supp...

54 OPERATION Engine Break-In Oil Injection System Always check and fill the oil tank when refueling. See page 59. NOTICE: Serious engine damage can occur without the proper lubrication. Check the oil tank level often during the first tank of fuel. If the oil level doesn't go down, contact your deale...

55 OPERATION Track Warm-Up WARNING! Use of traction products such as studs, ice growsers, etc. will increase the possibility of track damage and/or failure. This could cause loss of control, resulting in serious injury or death. Always inspect for track damage before operating the snowmobile. Follow...

56 OPERATION Slide Rail and Track Cooling NOTICE: Inadequate cooling and lubrication will lead to overheating of the slide rail and track, resulting in premature wear and failure. Reduce speeds and frequently drive into fresh snow to allow adequate cooling and polishing of the slide rail and track s...

57 OPERATION Fuel Fuel Valve Turn the fuel valve clockwise to OFF to shut off the fuel supply. Turn the valve counter-clockwise to ON to turn the fuel supply on. Fuel Recommendations Your Polaris engine is designed to run on 87 octane non-oxygenated or 89 octane oxygenated pump gasoline. There's a g...

58 OPERATION Fuel Fuel Reserve Capacity (Mechanical Gauge) There are approximately two gallons of fuel left in the tank when the mechanical fuel gauge reads RES. Fuel System Deicers If you use non-oxygenated fuel, Polaris recommends the regular use of isopropyl-based fuel system deicer. Add one to t...

59 OPERATION n Oil Low Oil Indicator Light The low oil indicator light will alert the operator if the oil level is low. Visually check for oil in the bottle. If oil is not visible, continued opera- tion may cause serious engine damage. Add oil before further operation of the snowmobile. Low Oil Leve...

60 OPERATION Carburetion Proper carburetor adjustment is critical. Always have your Polaris dealer perform any carburetor adjustments.A lean mixture (too much air, too little fuel) may result in piston burn- ing, bearing failure, or complete engine failure. A rich mixture (too much fuel, too little ...

61 OPERATION Carburetion Jetting Guidelines Changes in altitude and temperature affect air density, which is the amount of oxygen available for combustion. In low elevations and cold temperatures, the air has more oxygen. In higher elevations and higher temperatures, the air is less dense.The carbur...

62 OPERATION n Engine Stop Switch Push down on the engine stop switch ( + ) to ground out the ignition and stop the engine quickly. Pull the switch up to the ON position to allow restarting. n Throttle Safety Switch The throttle safety switch is designed to stop the engine whenever all pressure is r...

64 OPERATION Emergency Stopping The following chart lists methods for stopping the snowmobile in the event of an emergency. See page 62 for more information about the engine stop switch and throttle safety switch. WARNING! Excessive or repetitive use of brakes for high speed stops will cause an over...

65 OPERATION Electronic Reverse (PERC t ) Electronic reverse will activate only if the engine RPM is below 4000. If your machine is running at an altitude of over 6000 feet, adjust the igni- tion setting as described on page 67. Always make sure the vehicle is stopped and the engine is running at id...

66 OPERATION Electronic Reverse (PERC t ) Engaging Reverse 1. Stop the snowmobile and leave the engine idling.2. Make sure the area behind your vehicle is clear.3. Push the yellow reverse but- ton ( + ) on the left-hand con- trol for one second, then release. The engine will auto- matically reduce R...

67 OPERATION Electronic Reverse (PERC t ) Disengaging Reverse 1. Stop the snowmobile and leave the engine idling. NOTICE: Engaging the starter when the engine is running WILL result in serious engine damage, especially if the transmission is in reverse. Never engage the starter when the engine is ru...

68 OPERATION Towing Do not use the front bumper to pull or drag the snowmobile. The front bumper is not designed for this type of use and may detach from the vehicle if force is applied.For your safety, do not attempt to use a tow hitch until you've read the following warnings and understand the pro...

69 MAINTENANCE Emission Control Information Any qualified repair shop or qualified person may maintain, replace, or repair the emission control devices or systems on your snowmobile. Emission Control Label Your snowmobile is equipped at the time of sale with an emission con- trol information (ECI) l...

70 MAINTENANCE Polaris Recommended Maintenance Program To ensure many trouble-free miles of snowmobiling enjoyment, follow recommended regular maintenance and perform service checks as out- lined in this manual. Record maintenance and service in the Mainte- nance Log beginning on page 128.The recomm...

71 MAINTENANCE Periodic Maintenance Interval Table The following chart is a guide based on average riding conditions. You may need to increase frequency based on riding conditions. When inspection reveals the need for replacement parts, always use genuine Polaris parts, available from your Polaris d...

74 MAINTENANCE Lubrication Suspension and Steering Lubricate the suspension and steering components with Polaris Pre- mium All-Season Grease at 500 miles (800 km) and annually or every 1000 miles (1600 km) thereafter. See page 111 for the part numbers of Polaris products.The illustration shows the l...

75 MAINTENANCE Lubrication EDGE 136 Rear Suspension Driveshaft Bearing Inject grease into the fitting on the speed- ometer sensor housing until grease purges from the seal on the inside of the tunnel. This should take approximately two pumps. Do not use more than four pumps. Throttle Cable Lubricate...

76 MAINTENANCE Lubrication n Chaincase Oil Check the chaincase oil level at the intervals outlined in the mainte- nance charts beginning on page 70. Change the chaincase oil after the first 500 miles (800 km), then every 1000 miles (1600 km) or season- ally.Maintain the oil level between the “safe” ...

77 MAINTENANCE Spark Plugs It’s very important to use the correct spark plug for your machine. A spark plug with a heat range too high will cause engine damage. A spark plug with a heat range too low will cause excessive fouling and engine malfunctioning. NOTICE: A spark plug with a heat range too h...

78 MAINTENANCE Spark Plugs Normal Plug The normal insulator tip is gray, tan or light brown. There will be few combustion deposits. The electrodes are not burned or eroded. This indi- cates the proper type and heat range for the engine and the service.The tip should not be white. A white insulator t...

79 MAINTENANCE Intake Filters The intake foam filter ( + ) limits snow ingestion into the intake system. When operating in loose powder snow, check the top of the foam filter periodically to remove any accumulation of snow. NOTICE: Operating the snowmobile with the intake filters removed may cause c...

80 MAINTENANCE Fuel Filter/Fuel Lines The fuel filter is located inside the fuel tank. This component requires no maintenance.Inspect the fuel lines regularly for signs of deterioration or damage. Always check fuel line condition after periods of storage. Normal dete- rioration from weather and fuel...

81 MAINTENANCE Carburetor The number stamped in the end of the main jet indicates the jet size. The jet installed at the time of manufacture is not necessarily correct for your elevation. It's your dealer's responsibility to make sure the correct main jet is installed. NOTICE: Operating the snowmobi...

82 MAINTENANCE Carburetor Water/Sediment Trap Service Most Polaris snowmobiles contain patented carburetor bowl water/sedi- ment traps located at the bottom of each carburetor. The trap, consisting of a hose with a plug, should be drained at least every 2000 miles (3200 km) and inspected for contami...

83 MAINTENANCE Exhaust System Check the exhaust system for wear or damage at approximately 2000 miles (3200 km). To inspect, allow the engine and exhaust system to cool completely. Open the hood and inspect the muffler and pipes for cracks or damage. Check for weak or missing retaining springs or da...

84 MAINTENANCE Brakes n Hydraulic Brake Inspection Inspect the brake lever reserve before each use of the snowmobile. See page 47.Brake pads must be replaced when the brake pad material becomes thin- ner than the backing plate (approximately 1/16 inch/1.5 mm). A kit is available for replacing brake ...

85 MAINTENANCE Brakes Brake Fluid WARNING! After opening a bottle of brake fluid, always discard any unused portion. Never store or use a partial bottle. Brake fluid is hygroscopic, meaning it rapidly absorbs moisture from the air. The moisture causes the boiling temperature of the brake fluid to dr...

86 MAINTENANCE Brakes Bleeding the Hydraulic Brake System Air in the hydraulic brake system will cause spongy brake lever action. Bleed the system before operating the snowmobile. WARNING! Operating the vehicle with a spongy brake lever can result in loss of brakes, which could cause an accident and...

87 MAINTENANCE Lights Headlight Adjustment The headlight may be adjusted for vertical aim using the following pro- cedure.1. Place the snowmobile on a level surface with the headlight approxi- mately 25 feet (7.6 m) from a wall. 2. Measure the distance from the floor to the center of the headlight a...

88 MAINTENANCE Lights NOTICE: Do not touch a halogen bulb with bare fingers. Oil from skin leaves a residue, causing a hot spot that will shorten the life of the lamp. If fin- gers do touch the bulb, clean it with an alcohol-moistened towel. Headlight Bulb Replacement 1. Pinch the ends of the spring...

89 MAINTENANCE Clutch System Periodically inspect clutch sheaves for damage, wear or belt residue. To maintain optimum performance, clean with non-oil based cleaners such as isopropyl alcohol. NOTICE: If you become aware of higher than normal clutch engagement or an unusual vibration or shift patter...

90 MAINTENANCE Clutch System Drive Belt Removal 1. Stop the engine after operating in a forward motion. NOTICE: Do not attempt to remove the drive belt after operating in reverse. The snowmobile must be stopped after forward motion to prevent damage to components during belt removal. 2. Turn the ign...

91 MAINTENANCE Clutch System Drive Belt Installation 1. Drop the drive belt over the drive clutch and pull back the slack. Tip: To ensure satisfactory belt life, install belts so they operate in the same direction of rotation by positioning the identification numbers so that you can read them. If re...

92 MAINTENANCE Clutch System n Drive Belt Deflection Measure belt deflection with both clutches at rest and in their full neutral position.Place a straight edge (1) on the belt and apply downward pressure while measuring at point 2. This measurement should be 1 1/4 inches (32 mm). Drive Belt Adjustm...

93 MAINTENANCE Clutch System Torque Stop If your snowmobile is equipped with an engine torque stop, periodically check torque stop clearance.With clutches in proper alignment, the torque stop clearance should be .010- .030 inch (.25-.75 mm) from the engine case.Adjust if necessary, and lock the jam ...

94 MAINTENANCE Chain Tension Maintain the proper chain tension as outlined on page 83. Fall Tune-Up For maximum performance, arrange for a fall service tune-up with your Polaris dealer. His experienced and trained service technician will keep your machine in peak operating condition. Tool Kit A tool...

95 MAINTENANCE Track Track Inspection WARNING! Broken track rods can cause a rotating track to come off the machine, which could cause serious injury or death. Never operate with a damaged track. Never rotate a damaged track under power. 1. Using a hoist, safely lift and support the rear of the snow...

96 MAINTENANCE Track Moving parts can cut and crush body parts. When performing the checks and adjustments recommended on the following pages, stay clear of all moving parts. Never perform track measurement or adjustments with the engine run- ning. Track Tension Track adjustment is critical for prop...

97 MAINTENANCE Track Track Tension If the track needs adjustment: 6. Loosen the rear idler shaft bolts. 7. Loosen the locknuts. 8. Tighten or loosen the track adjusting screws to provide equal adjustment on both sides of the track. 9. Repeat the measure- ment on the other side of the track. Tip: Che...

98 MAINTENANCE Track n Track Alignment Periodically check that the track is centered and running evenly on the slide rails. Misalignment will cause excessive wear to the track and slide rail.1. Safely support the rear of the machine with the track off the ground.2. Start the engine and apply a small...

99 MAINTENANCE Steering System n Rail Slide Wear For ease of inspection, all Polaris rail slides have a wear limit indicator groove to indicate the minimum permissible slide thickness. Replace the rail slides if they are worn to the top of the groove at any point along their length. Failure to do so...

100 MAINTENANCE Steering System Ski Alignment WARNING! Improper ski alignment or adjustment may cause loss of steering control, resulting in serious injury or death. Do not attempt to change the ski alignment or camber adjustment. See your Polaris dealer. With the handlebars in a straight ahead posi...

101 MAINTENANCE Steering System n Ski Skags See your dealer's studding chart for recommended skags. If you install longer or more aggressive carbide skags than the original equipment, it may also be necessary to add track studs to maintain proper vehicle con- trol while turning on hard-packed snow o...

102 MAINTENANCE Battery Battery electrolyte is poisonous. It contains acid! Serious burns can result from contact with the skin, eyes, or clothing. If contact occurs, seek immediate medi- cal attention.KEEP OUT OF REACH OF CHILDREN.EXTERNAL: Flush with water.INTERNAL: Drink large quantities of water...

103 MAINTENANCE Battery Battery Removal WARNING! Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death. When removing the battery, always disconnect the negative (black) cable first. When reinstalling the battery, always connect the negati...

104 MAINTENANCE Battery Battery Installation WARNING! Battery electrolyte contains acid. Avoid skin contact with electrolyte as severe burns may result. Using a new battery that has not been fully charged can damage the bat- tery and result in a shorter life. It can also hinder vehicle performance. ...

105 MAINTENANCE Battery Battery Storage When your snowmobile is placed in storage for one month or more:• Remove the battery.• Charge it to the proper level.• Store it in a cool dry place.• Check and/or charge monthly.• Have the battery tested and recharged before reinstalling it in the vehicle. If ...

106 MAINTENANCE n Pre-Ride Suspension Inspection Loose nuts and bolts can reduce your snowmobile's reliability and cause needless repairs and down time. Before beginning any snowmobile trip, a visual inspection will uncover potential problems. Check the follow- ing items on a weekly basis or before ...

107 MAINTENANCE Extended Storage Off-season or extended storage of your snowmobile requires preventive measures to aid against deterioration and to prolong the useful life of many components. See page 111 for the part numbers of Polaris prod- ucts. Cleaning and Preservation Proper storage starts wit...

108 MAINTENANCE Extended Storage Bearings Grease the drive shaft clutch side bearing with Polaris Premium All- Season Grease or a similar high quality grease to prevent corrosion. Clutch and Drive System Remove the drive belt and store in a cool dry location. To prevent oxida- tion on the clutch she...

110 MAINTENANCE Extended Storage Electrical Connections Separate electrical connector blocks and clean corrosive build-up from connectors. Lubricate or pack connector blocks with dielectric grease and re-connect. Replace worn or frayed electrical wire and connectors. Be sure wiring harness is proper...

111 POLARIS PRODUCTS Part No. Description Engine Lubricants 2870791 Fogging Oil (12 oz. Aerosol) 2871098 Premium 2-Cycle Engine Oil (qt.) 2871097 Premium 2-Cycle Engine Oil (gal.) 2871240 Premium 2-Cycle Engine Oil (2.5 gal.) 2871721 Premium Gold Synthetic 2-Cycle Engine Oil (qt.) 2871722 Premium Go...

112 TROUBLESHOOTING Engine Troubleshooting Unless you have experience and training in two-cycle engine repair, see your dealer if technical problems arise. Problem Probable Cause Solution Erratic engine oper- ating RPM during acceleration or load variations Drive clutch binding • Disassemble drive c...

116 TROUBLESHOOTING Drive Belt Troubleshooting Belt Wear/Burn Diagnosis Causes Solutions Driving at low RPM • Drive at higher RPMs. Gear the machine down. Check belt deflection. Insufficient warm-up • Warm the engine at least five minutes. Take the drive belt off the machine in extremely cold weathe...

117 WARRANTY Service and Warranty Information Obtaining Service and Warranty Assistance Read and understand the service data and the Polaris warranty informa- tion contained in this manual. Contact your Polaris dealer for replace- ment parts, service or warranty. Your dealer receives frequent update...

118 WARRANTY Service and Warranty Information Polaris Anti-Theft System The Polaris anti-theft system (PATS) monitoring program is designed to aid owners of registered snowmobiles in recovery of stolen machines. Administration 1. Polaris snowmobile owner reports theft. A. In addition to notifying th...

119 WARRANTY Limited Warranty Polaris Sales Inc., 2100 Highway 55, Medina, MN 55340, provides a ONE YEAR LIM- ITED WARRANTY on all components of the Polaris snowmobile against defects in material or workmanship. This warranty covers the parts and labor charges for repair or replacement of defective ...

121 WARRANTY Conditions and Exclusions In order to qualify for warranty, the product must have been properly set up and tested by a Polaris Dealer (if applicable). Failure of any dealer to perform the required vehicle Pre-Delivery Inspection, perform all applicable service bulletins and have the con...

122 WARRANTY Polaris Second Year Engine Service Contract Second Year Engine Service Contract is standard on all eligible new and unused snow- mobiles that were Snow Checked through an authorized Polaris dealer during the March/April Snow Check promotion. The free Second Year Engine Service Contract ...

123 WARRANTY Polaris Second Year Engine Service Contract Coverage Coverage for second year engine failures due to defects in materials and workmanship will be determined by Polaris in its sole discretion. Coverage is automatic with no addi- tional paperwork required. The free Second Year Engine Serv...

124 WARRANTY Exported Vehicles EXCEPT WHERE SPECIFICALLY REQUIRED BY LAW, THERE IS NO WAR- RANTY OR SERVICE BULLETIN COVERAGE ON THIS VEHICLE IF IT IS SOLD OUTSIDE THE COUNTRY OF THE SELLING DEALER'S AUTHORIZED LOCA- TION.This policy does not apply to vehicles that have received authorization for ex...

125 WARRANTY Exported Vehicles How to Get Service In the Country where your vehicle was purchased: Warranty or Service Bulletin repairs must be done by an authorized Polaris dealer. If you move or are traveling within the country where your vehicle was purchased, Warranty or Service Bulletin repairs...

128 MAINTENANCE LOG Present this section of your manual to your dealer each time your snow- mobile is serviced. This will provide you and future owners with an accurate log of maintenance and services performed on the snowmobile. DATE MILES (KM) TECHNICIAN SERVICE PERFORMED / COMMENTS 150 mi. (240 k...

132 INDEX A Accessories . . . . . . . . . . . . . . . . . . . 44 Air Box Warning . . . . . . . . . . . . . . . 22 Air Pollution . . . . . . . . . . . . . . . . . . . 5 Altitude Setting . . . . . . . . . . . . . . . . 67 Avalanches. . . . . . . . . . . . . . . . . . . . 14 B Backrest . . . . . . . . ...