Polaris 9921777 - Manuals

3 TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Features and Controls . . . . . . . . . . . . . . . . . . . 26Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Emis...

4 INTRODUCTION The following signal words and symbols appear throughout this manual and on your vehicle. Your safety is involved when these words and sym- bols are used. Become familiar with their meanings before reading the manual. The safety alert symbol indicates a potential personal injury hazar...

6 INTRODUCTION Vehicle Identification Numbers Record your vehicle's identification numbers and key number in the spaces provided. Remove the spare key and store it in a safe place. An ignition key can be duplicated only by ordering a Polaris key blank (using your key number) and mating it with one o...

7 SAFETY Safety Training ATV safety training is a top priority for Polaris. When you purchased your new ATV, your dealer instructed you on the authorized ATV RiderCourse sm available to you and your eligible family members. This training is included in the purchase price of your ATV. Polaris strongl...

8 SAFETY Safe Riding Gear Always wear appropriate clothing when riding an ATV. Wear protective clothing for comfort and to reduce the chance of injury. Helmet Wearing a helmet can prevent a severe head injury. Whenever riding a Polaris vehicle, always wear a helmet that meets or exceeds established ...

9 SAFETY Safe Riding Gear Eye Protection Do not depend on eyeglasses or sunglasses for eye protection. When- ever riding a Polaris vehicle, always wear shatterproof goggles or use a shatterproof helmet face shield. Polaris recommends wearing approved Personal Protective Equipment (PPE) bearing marki...

10 SAFETY Safety Warnings Failure to operate the ATV properly can result in a collision, loss of control, accident or overturn, which may result in serious injury or death. Heed all safety warnings outlined in this section of the owner’s manual. See the OPERATION section of the owner’s manual for pr...

11 SAFETY Safety Warnings Handling Gasoline Gasoline is highly flammable and explosive under certain conditions. • Always exercise extreme caution whenever handling gasoline.• Always refuel with the engine stopped, and outdoors or in a well ventilated area. • Do not smoke or allow open flames or spa...

12 SAFETY Safety Warnings Protective Apparel Riding in this vehicle without wearing an approved helmet and protective eyewear increases the risk of a serious injuries in the event of an accident.Operator and passenger must always wear an approved helmet that fits properly and eye protection (goggles...

13 SAFETY Safety Warnings Operating on Pavement Operating an ATV on paved surfaces (including sidewalks, paths, parking lots and driveways) may adversely affect the handling of the ATV and could result in loss of control and accident or overturn.Avoid operating the ATV on pavement. ATV tires are des...

14 SAFETY Safety Warnings Physical Control of the ATV Removing a hand from the handlebars or feet from the footrests during operation can reduce your ability to control the vehicle or cause loss of balance and ejection from the ATV. If the operator's foot is not firmly planted on the footrest, it co...

15 SAFETY Safety Warnings Descending Hills Improperly Improperly descending a hill could cause loss of control or overturn.• Always follow proper procedures for travel- ing down hills as described in the owner's manual. NOTE: A special technique is required when braking while traveling down- hill. S...

16 SAFETY Safety Warnings Stalling While Climbing a Hill Stalling, rolling backwards or improperly dismounting while climbing a hill could cause an overturn.• Always maintain a steady speed when climbing a hill. If all forward speed is lost:• Keep body weight uphill.• Apply the single-lever brake gr...

17 SAFETY Safety Warnings Operating on Slippery Terrain Failure to use extra caution when operating on excessively rough, slippery or loose terrain could cause loss of traction, loss of control, accident or overturn.Do not operate on excessively rough, slippery or loose terrain. Always use extra cau...

18 SAFETY Safety Warnings Operating Improperly in Reverse Improperly operating in reverse could result in a collision with an obstacle or person. Always follow proper operating procedures as outlined in this manual. See page 54. Before shifting into reverse gear, always check for obstacles or people...

19 SAFETY Safety Warnings Operating Over Obstacles Improperly operating over obstacles could cause loss of control or overturn.Before operating in a new area, check for obstacles. Avoid operating over large obstacles such as rocks and fallen trees. If unavoidable, use extreme caution and always foll...

20 SAFETY Safety Warnings Improper Cargo Loading Overloading the ATV or carrying/towing cargo improperly may cause changes in handling, which could cause loss of control or an accident.• Never exceed the stated load capacity for this ATV.• Cargo should be properly distributed and securely attached.•...

21 SAFETY Safety Warnings Operating a Damaged ATV Operating a damaged ATV can result in an accident. After any overturn or accident, have a qualified service dealer inspect the entire machine for possible damage, including (but not limited to) brakes, throttle and steering systems. Physical Skills S...

22 SAFETY Safety Labels and Locations Warning labels have been placed on the vehicle for your protection. Read and follow the instructions on each label carefully. If any of the labels shown in this manual differ from the labels on your vehicle, always read and follow the instructions of the labels ...

23 SAFETY Safety Labels and Locations Discretionary Warning WARNING• Never operate this ATV on HILLS steeper than 25 degrees 25 ° . To pre- vent overturn on hilly terrain, use throttle and brakes gradually, and shift weight uphill. • REVERSE operation can be dangerous even at low speeds. Steering be...

24 SAFETY Safety Labels and Locations “No Passenger” Warning WARNINGNEVER ride as a passenger.Passengers can cause a loss of control, resulting in SEVERE INJURY or DEATH. 7175378 Tire Pressure/Load Warning WARNINGImproper tire pressure or overloading can cause loss of control. Loss of control can re...

25 SAFETY Safety Labels and Locations Age 16 Warning WARNINGOperating this ATV if you are under the age of 16 increases your chance of severe injury or death.NEVER operate this ATV if you are under age 16. 7175374 Clutch Cover Warning WARNING• Moving parts hazard under belt-clutch guard. To prevent ...

26 FEATURES AND CONTROLS Switches Override Switch This vehicle is equipped with a reverse speed limiter system. To gain additional wheel speed while backing, release the throttle and press the override switch. WARNING! Pressing the override switch while the throttle is open can cause loss of control...

27 FEATURES AND CONTROLS Switches Headlight Switch Use the headlight switch to turn the lights on and off and to change the lights from high beam to low beam. The key must be in the ON position and the engine stop switch must be in the RUN position to operate the headlights. All Wheel Drive Switch S...

28 FEATURES AND CONTROLS Throttle Lever Operating an ATV with sticking or improperly operating throttle controls could cause an accident. Never start or operate an ATV that has a sticking or improperly operating throttle. Always contact your dealer for service before operating the vehicle.Failure to...

29 FEATURES AND CONTROLS Brake Lever Operating the ATV with a spongy brake lever can result in loss of braking, which could cause an accident. Never operate the ATV with a spongy-feeling brake lever. Always contact your dealer for service before operating the vehicle. Squeeze the brake lever toward ...

30 FEATURES AND CONTROLS Parking Brake Locking the Parking Brake 1. Place the transmission in gear. 2. Squeeze and release the brake lever two or three times, then squeeze and hold. 3. Push the parking brake lock forward to engage the lock. 4. Release the brake lever.5. To release the parking brake ...

31 FEATURES AND CONTROLS Auxiliary Foot Brake Aggressively applying the auxiliary brake when backing down a hill may cause rear tipover, which could result in serious injury or death. Never back down a hill.Use caution when applying the auxiliary brake. Do not aggressively apply the auxiliary brake ...

32 FEATURES AND CONTROLS Brake Fluid An over-full master cylinder may cause brake drag or brake lock-up, which could result in an accident. Maintain brake fluid at the recommended level. Do not overfill.Never store or use a partial bottle of brake fluid. Brake fluid is hygroscopic, meaning it rapidl...

33 FEATURES AND CONTROLS Brake Fluid Hand Brake Check the brake fluid level in the master cylinder before each use of the vehicle. The master cylinder is located on the left handlebar. Maintain the fluid level 1/4" (6 mm) below the top edge of the master cylinder. Do not overfill.1. Position the...

34 FEATURES AND CONTROLS Choke The choke assists in starting a cold engine. Refer to the engine starting procedure on page 43 for correct choke and throttle settings during start- ing. Fuel Tank Cap Always refuel with the engine stopped, and outdoors or in a well ventilated area. Refuel on a level s...

35 FEATURES AND CONTROLS Automatic Transmission Gear Selector The transmission gear selector is located on the right side of the vehicle. F: Forward GearN: NeutralR: ReverseTo shift gears, brake to a complete stop. When the engine is idling, move the lever to the desired gear. NOTICE: Shifting gears...

36 FEATURES AND CONTROLS All Wheel Drive (AWD) System The All Wheel Drive system is controlled by the AWD switch. When the switch is on 2X4, the ATV is in two-wheel drive at all times. When the switch is on AWD, the ATV is in all wheel drive and the AWD indicator light will be on.When in AWD, the fr...

37 FEATURES AND CONTROLS All Wheel Drive (AWD) System Disengaging AWD Although the hubs normally disengage when operating in reverse, one or both hubs may occasionally remain engaged. If the handlebars pull to one side, it's likely that one front hub is engaged. If both hubs are engaged, steering ef...

38 OPERATION Failure to operate the ATV properly can result in a collision, loss of control, accident or overturn, which may result in serious injury or death. Read and understand all safety warnings outlined in the safety section of this owner’s manual. Break-In Period The break-in period for your ...

39 OPERATION Break-In Period Engine and Drivetrain Break-in 1. Fill the fuel tank with gasoline. See page 34. Always exercise extreme caution whenever handling gasoline. 2. Check the oil level on the dipstick. See page 66. Add oil if neces- sary to maintain the level in the safe operating range. 3. ...

40 OPERATION Safe Operation Practices 1. Complete the recommended safety training before operating this vehicle. See page 7. 2. Do not allow anyone under 16 years of age to operate this vehicle. Do not allow anyone with cognitive or physical disabilities to oper- ate this vehicle. 3. Never carry a p...

41 OPERATION Know Your Riding Area/Tread Lightly Familiarize yourself with all laws and regulations concerning the opera- tion of this off-road vehicle in your area. Respect the environment in which you ride. Find out where the designated riding areas are by con- tacting your Polaris dealer, a local...

42 OPERATION Pre-Ride Checklist Failure to inspect and verify that the ATV is in safe operating condition before operating increases the risk of an accident. Always inspect the ATV before each use to make sure it's in safe operating condition. Item Remarks Page Brake system/lever travel Ensure prope...

43 OPERATION Starting the Engine 1. Position the vehicle on a level surface outdoors or in a well-venti- lated area. 2. Place the transmission in neutral.3. Lock the parking brake. Tip: The starter interlock will prevent the engine from starting if the transmission is in gear and the brake is not en...

45 OPERATION Driving Procedures 1. Wear a helmet and eye protection. See page 8.2. Sit upright with both feet on the footrests and both hands on the handlebars. 3. Start the engine and allow it to warm up. 4. Shift the transmission into gear.5. Check your surroundings and determine your path of trav...

46 OPERATION Turning the Vehicle Your ATV is equipped with a solid rear axle, which drives both rear wheels equally at all times. This means that the wheel on the outside of the turn must travel a greater distance than the inside wheel when turning and the inside tire must slip traction slightly. To...

47 OPERATION Driving on Slippery Surfaces Whenever riding on slippery surfaces such as wet trails or loose gravel, or during freezing weather, follow these precautions:1. Do not operate on excessively rough, slippery or loose terrain.2. Slow down when entering slippery areas.3. Engage AWD before whe...

48 OPERATION Driving Uphill Braking and handling are greatly affected when operating in hilly ter- rain. Improper procedure could cause loss of control or overturn. When- ever traveling uphill, follow these precautions:1. Drive straight uphill.2. Avoid steep hills (25 ° maximum). 3. Always check the...

49 OPERATION Driving on a Sidehill (Sidehilling) Driving on a sidehill is not recommended. Improper procedure could cause loss of control or overturn. Avoid crossing the side of any hill unless absolutely necessary.If crossing a sidehill is unavoidable , follow these precautions: 1. Slow down.2. Avo...

50 OPERATION Driving Downhill When driving downhill, follow these precautions:1. Avoid steep hills (25 ° maximum). 2. Shift body weight uphill.3. Drive straight downhill.4. Slow down. Excessive speed when traveling downhill can cause loss of control. 5. Squeeze the brake lever gradually. Applying th...

51 OPERATION Turning Around on a Hill (K-Turn) If the vehicle stalls while climbing a hill, never back it down the hill! Use the K-turn to turn around. 1. Stop and lock the parking brake while keeping body weight uphill.2. Leave the transmission in forward and shut off the engine.3. Dismount on the ...

52 OPERATION Driving Through Water Your ATV can operate through water with a maxi- mum recommended depth equal to the bottom of the footrests. Follow these pro- cedures when operating through water:1. Determine water depths and current before entering water. 2. Choose a crossing where both banks hav...

53 OPERATION Driving Over Obstacles Follow these precautions when operating over obstacles:1. Always check for obstacles before operating in a new area.2. Look ahead and learn to read the terrain. Be constantly alert for haz- ards such as logs, rocks and low hanging branches. 3. Travel slowly and us...

54 OPERATION Driving in Reverse Follow these precautions when operating in reverse:1. Always check for obstacles or people behind the vehicle.2. Always avoid backing downhill.3. Back slowly.4. Apply the brakes lightly for stopping. 5. Avoid turning at sharp angles.6. Never open the throttle suddenly...

55 OPERATION Parking on an Incline Avoid parking on an incline if possible. If it's unavoidable, follow these precautions:1. Stop the engine.2. Place the transmission in gear.3. Lock the parking brake.4. Always block the rear wheels on the downhill side.5. Turn the fuel valve off.

56 OPERATION Hauling Cargo Overloading the vehicle or carrying or towing cargo improperly can alter vehicle handling and may cause loss of control or brake instability, which can result in serious injury or death. Always follow these precautions when hauling cargo:REDUCE SPEED AND ALLOW GREATER DIST...

57 OPERATION Hauling Cargo Never exceed the weight capacities specified for your ATV on warning labels and in the specifications section of this manual.Cargo weight should be evenly distributed (1/3 on the front rack and 2/3 on the rear rack) and mounted as low as possible. When operating over rough...

58 EMISSION CONTROL SYSTEMS Noise Emission Control System Do not modify the engine, intake or exhaust components, as doing so may affect compliance with U.S.A. EPA noise control requirements (40 CFR 205) and local noise level requirements. Operation on Public Lands in the U.S.A. Your Polaris vehicle...

59 MAINTENANCE Periodic Maintenance Chart Careful periodic maintenance will help keep your vehicle in the safest, most reliable condition. Inspection, adjustment and lubrication of important components are explained in the periodic maintenance chart.Inspect, clean, lubricate, adjust and replace part...

60 MAINTENANCE Periodic Maintenance Chart Improperly performing the procedures marked with a „ could result in component failure and cause an accident, which may result in serious injury or death. Always have an authorized Polaris dealer perform these services. Maintenance Chart Key X Perform these ...

64 MAINTENANCE Lubrication Guide Check and lubricate all components at the intervals outlined in the Peri- odic Maintenance Chart beginning on page 59. Items not listed in the chart should be lubricated at the General Lubrication interval. See page 111 for the part numbers of Polaris products.The a-...

66 MAINTENANCE Engine Oil Oil Recommendations Polaris recommends the use of Polaris PS-4 PLUS Performance Syn- thetic 2W-50 4-cycle oil or a similar oil for this engine. Oil may need to be changed more frequently if Polaris oil is not used. Always use 2W-50 oil. Follow the manufacturer's recommendat...

67 MAINTENANCE Oil and Filter Change Always change the oil and filter at the intervals outlined in the Periodic Maintenance Chart beginning on page 59. Always change the oil filter whenever changing oil.1. Position the vehicle on a level surface. Clean the area around the drain plug at the bottom of...

68 MAINTENANCE Oil and Filter Change 8. Place towels under the oil filter. Using an oil filter wrench, turn the filter counterclockwise to remove it. 9. Lubricate the gasket on the new filter with a film of new engine oil. Check to make sure the gasket is in good condition. Make sure the gasket from...

69 MAINTENANCE Oil and Filter Change Oil Pump Priming This priming procedure must be performed whenever the oil hose connection between the oil tank and pump inlet has been disconnected.1. Clamp or pinch off the vent line approximately two inches (5 cm) from the oil tank, between the end of the oil ...

70 MAINTENANCE Transmission Oil Always check and change the transmission oil at the intervals outlined in the Periodic Maintenance Chart beginning on page 59. Maintain the oil level at the bottom of the fill hole threads. See page 111 for the part numbers of Polaris products.The fill plug is located...

71 MAINTENANCE Transmission Oil Oil Change 1. Position the vehicle on a level surface.2. Remove the propshaft shield from the right side of the vehicle to access the fill plug. Remove the fill plug. 3. Remove the transmission drain plug located on the bottom left-hand side and drain the oil into an ...

72 MAINTENANCE Front Gearcase Fluid Always check and change the front gearcase fluid at the intervals out- lined in the Periodic Maintenance Chart beginning on page 59. Maintain the fluid level at the bottom of the fill hole threads. See page 111 for the part numbers of Polaris products. Front Gearc...

73 MAINTENANCE Brakes The front and rear brakes are hydraulic disc brakes, activated by moving the single brake lever toward the handlebar. The auxiliary foot brake is also hydraulic. Both brake systems are self-adjusting. Brake Inspections The following checks are recommended to keep the brake syst...

74 MAINTENANCE Toe Alignment Use the following procedure to check the toe alignment of the vehicle. The recommended toe alignment is 1/8" to 1/4" (3-6 mm) toe out. WARNING! Severe injury or death can result from improper toe alignment and adjustment. Do not attempt to adjust tie rod alignmen...

75 MAINTENANCE Steering Assembly The steering assembly of the ATV should be checked periodically for loose nuts and bolts. If loose nuts and bolts are found, see your Polaris dealer for service before operating the vehicle. Camber and Caster The camber and caster are non-adjustable. Rear Spring The ...

76 MAINTENANCE Handlebars The handlebars can be adjusted for rider preference. WARNING! Improper adjustment of the handlebars or incorrect torquing of the adjuster block tightening bolts can cause limited steering or loosening of the handlebars, resulting in loss of control and serious injury or dea...

77 MAINTENANCE Tires Operating your ATV with worn tires, improperly inflated tires, non-standard tires or improperly installed tires will affect vehicle handling and could cause an accident resulting in serious injury or death. Always follow all tire maintenance procedures as outlined in this manual...

78 MAINTENANCE Tires Wheel Removal 1. Position the vehicle on a level surface. Place the transmission in gear. Lock the parking brake. 2. Loosen the wheel nuts slightly. WARNING! Do not service axle nuts that have a cotter pin installed. See your Polaris dealer. 3. Place a suitable stand under the f...

79 MAINTENANCE Tires Wheel Nut Torque Specifications Check the wheel nut torques occasionally and when they've been loos- ened for service. Item Torque Specification Front Wheel Nuts 27 ft. lbs. (37 Nm) Rear Wheel Nuts 50 ft. lbs. (68 Nm) Rear 50 ft. lbs. (68 Nm) Front 27 ft. lbs. (37 Nm)

80 MAINTENANCE Air Filter 1. Position the vehicle on a level surface. Place the transmission in gear. Lock the parking brake. 2. Remove the seat.3. Release the air box cover clips, and remove the air box cover. 4. Loosen the clamp and remove the filter. 5. Remove the pre-filter from the main filter....

82 MAINTENANCE Carburetor Your Polaris ATV is calibrated at the factory for optimal performance at altitudes ranging from zero to 6,000 feet (1800 m) and temperatures of +40 degrees F. (4 degrees C.) or higher. Above 6000 feet (1800 m) the engine air/fuel mixture becomes overly rich and the engine l...

83 MAINTENANCE Drive Chain Drive Chain Lubrication Polaris ATV drive chains are equipped with o-ring-sealed, permanently greased pins and rollers. However, the outer surfaces of the roller must be lubricated.Always inspect the drive chain prior to operating the vehicle. Check for damaged or missing ...

84 MAINTENANCE Drive Chain Rear Drive Chain Slack Check the amount of chain slack in three different locations by moving the vehicle slightly forward to gain slack at the top side of the rear chain. Measure the chain slack at the tightest of the three positions. At this point the chain should have 3...

86 MAINTENANCE Cooling System The engine coolant level is controlled, or maintained, by the recovery system. The recovery system components are the recovery bottle, the radiator filler neck, the radiator pressure cap and the connecting hose.As coolant operating temperature increases, the expanding (...

87 MAINTENANCE Cooling System Radiator Coolant To ensure that the coolant maintains its ability to protect the engine, Polaris recommends that you drain the system completely every two years and add a fresh mixture of antifreeze and water.Replace the coolant any time the cooling system has been drai...

88 MAINTENANCE Lights Headlight Beam Adjustment The headlight beam can be adjusted slightly upward or downward. Use the following procedure to make the adjustment. 1. Position the vehicle on a level surface with the headlight approxi- mately 25 ft. (7.6 m) from a wall. 2. Place the transmission in n...

89 MAINTENANCE Lights Poor lighting can result in reduced visibility when driving. Headlight and taillight lenses become dirty during normal operation. Clean lights frequently and replace burned out lamps promptly. Always make sure lights are adjusted properly for best visibility. Headlamp Replaceme...

90 MAINTENANCE Lights Taillight/Brakelight Lamp Replacement 1. Remove the taillight lens cover mounting screws. Remove the lens cover and gasket and set aside for reassembly. 2. Remove the lamp.3. Apply dielectric grease to the socket and install the new lamp. 4. Test the taillight/brake light for p...

91 MAINTENANCE Spark Plugs Spark Plug Recommendations Refer to the specifications section beginning on page 116 for the recom- mended spark plug type and gap for your vehicle. Torque spark plugs to specification. NOTICE: Using non-recommended spark plugs can result in serious engine damage. Always u...

92 MAINTENANCE Spark Plugs Spark Plug Condition Normal Spark Plug The normal insulator tip is gray, tan or light brown. There will be few combustion deposits. The electrodes are not burned or eroded. This indi- cates the proper type and heat range for the engine and the service.The tip should not be...

93 MAINTENANCE Vehicle Immersion If your vehicle becomes immersed, major engine damage can result if the machine is not thoroughly inspected. Take the vehicle to your dealer before starting the engine. If it's impossible to take your ATV to a dealer before starting it, follow the steps outlined belo...

94 MAINTENANCE Spark Arrestor Failure to heed the following warnings while servicing the spark arrestor could result in serious injury or death. Never run the engine in an enclosed area. Remove any combustible materials from the area. Wear eye protection and leather work gloves. Do not stand behind ...

95 MAINTENANCE PVT System Failure to comply with the instructions in this warning can result in severe injury or death.Do not modify any component of the PVT system. Doing so may reduce its strength so that a failure may occur at a high speed. The PVT system has been precision balanced. Any modifica...

96 MAINTENANCE PVT System The basic operation of the Polaris PVT system is dependent on engine speed and vehicle torque requirements. As engine speed increases, the force exerted on the movable drive sheave by the flyweights also increases. This, in turn, increases the amount of pinch applied to the...

97 MAINTENANCE PVT System PVT Drying There may be some instances when water is accidently ingested into the PVT system. Use the following instructions to dry it out before operat- ing.1. Move the vehicle out of the water.2. Remove the PVT drain plug. Allow the water to drain completely. Reinstall th...

98 MAINTENANCE Battery Improperly connecting or disconnecting battery cables can result in an explosion and cause serious injury or death. When removing the battery, always disconnect the negative (black) cable first. When reinstalling the battery, always connect the negative (black) cable last. Bat...

99 MAINTENANCE Battery Battery Removal 1. Place the transmission in gear.2. Lock the parking brake.3. Disconnect the battery hold-down strap.4. Remove the battery cover.5. On conventional batteries, remove the battery vent tube.6. Disconnect the black (negative) battery cable first.7. Disconnect the...

100 MAINTENANCE Battery Battery Installation Using a new battery that has not been fully charged can damage the bat- tery and result in a shorter life. It can also hinder vehicle performance. Follow the battery charging instructions on page 102 before installing the battery.1. Ensure that the batter...

101 MAINTENANCE Battery Battery Storage Whenever the vehicle is not used for a period of three months or more, remove the battery from the vehicle, ensure that it's fully charged, and store it out of the sun in a cool, dry place. Check battery voltage each month during storage and recharge as needed...

102 MAINTENANCE Battery Battery Charging (Conventional Battery) 1. Remove the battery from the vehicle to prevent damage from leak- ing or spilled electrolyte during charging. See page 99. 2. Charge the battery with a charging output no larger than 1/10 of the battery’s amp/hr rating. Charge as need...

103 MAINTENANCE Battery Battery Charging (Sealed Battery) Always verify battery condition before and 1-2 hours after the end of charging. State of Charge Voltage Action Charge Time (Using constant current charger @ standard amps specified on top of battery) 100% 12.8-13.0 volts None, check at 3 mos....

104 MAINTENANCE Cleaning and Storage Washing the Vehicle Keeping your Polaris vehicle clean will not only improve its appearance but it can also extend the life of various components. NOTICE: High water pressure may damage components. Polaris recommends washing the vehicle by hand or with a garden h...

105 MAINTENANCE Cleaning and Storage Washing the Vehicle If a high pressure water system is used for cleaning (not recommended), exercise extreme caution. The water may damage components and could remove paint and decals. Avoid directing the water stream at the follow- ing items: If an informational...

106 MAINTENANCE Cleaning and Storage Chrome Wheel Care (if equipped) Proper maintenance will protect chrome wheels from corrosion, pre- serve wheel life and ensure a “like new” appearance for many years. Chrome wheels exposed to road salt (or salt in the air in coastal areas) are more susceptible to...

107 MAINTENANCE Cleaning and Storage Storage Tips NOTICE: Starting the engine during the storage period will disturb the protective film created by fogging and damage could occur. Never start the engine during the storage period. Clean the Exterior Make any necessary repairs and clean the vehicle as...

108 MAINTENANCE Cleaning and Storage Storage Tips Fluid Levels Inspect the fluid levels. Change fluids as recommended in the Periodic Maintenance Chart beginning on page 59.• Demand drive unit (front gearcase)• Transmission• Brake fluid (change every two years and any time the fluid looks dark or co...

109 MAINTENANCE Cleaning and Storage Storage Tips Inspect and Lubricate Inspect all cables and lubricate all areas of the vehicle as recommended in the Periodic Maintenance Chart beginning on page 59. Battery Storage See pages 101-102 for storage and charging procedures. Storage Area/Covers Set the ...

110 MAINTENANCE Transporting the Vehicle Follow these procedures when transporting the vehicle.1. Stop the engine.2. Place the transmission in gear. 3. Lock the parking brake.4. Turn the fuel valve off.5. Secure the fuel cap, oil cap and seat. 6. Remove the key to prevent loss during transporting. 7...

111 POLARIS PRODUCTS Part # Description Engine Lubricant 2870791 Fogging Oil (12 oz. Aerosol) 2876244 PS-4 PLUS Performance Synthetic 2W-50 4-Cycle Oil (qt./.95 l) 2876245 PS-4 PLUS Performance Synthetic 2W-50 4-Cycle Oil (gal./3.8 l) Gearcase / Transmission Lubricants 2873602 Premium AGL Synthetic ...

112 TROUBLESHOOTING Drive Belt Wear/Burn Possible Cause Solution Starting out going up a steep incline Use low range (if equipped) or turn around using the K- turn (see page 51). Driving at low RPM or ground speed (3-7 MPH) Drive at a higher speed or use low range (if equipped) more frequently. Insu...

113 TROUBLESHOOTING Engine Doesn't Turn Over Engine Turns Over, Fails to Start Engine Backfires Possible Cause Solution Tripped circuit breaker Reset the breaker Low battery voltage Recharge the battery to 12.8 VDC Loose battery connections Check all connections and tighten Loose solenoid connection...

114 TROUBLESHOOTING Engine Pings or Knocks Engine Runs Irregularly, Stalls or Misfires Possible Cause Solution Poor quality or low octane fuel Replace with recommended fuel Incorrect ignition timing See your dealer Incorrect spark plug gap or heat range Set gap to specs or replace plugs Idle set too...

115 TROUBLESHOOTING Engine Stops or Loses Power Possible Cause Solution Out of fuel Turn fuel valve to reserve, refuel Kinked or plugged fuel vent line Inspect and replace Water is present in fuel Replace with new fuel Overuse of choke Inspect, clean and/or replace spark plugs Fouled or defective sp...

116 SPECIFICATIONS * Based on EU Directive 76/432/EC Scrambler 500 4X4 Maximum Weight Capacity 275 lbs. (125 kg) (includes weight of opera- tor, cargo and accessories) Dry Weight 571 lbs. (259.5 kg) Fuel Capacity 3.5 gal. (13.2 l) Engine Oil Capacity 2 qts. (1.9 l) Transmission Oil 32 oz. (946 ml) F...

117 SPECIFICATIONS Jetting Chart Clutching Chart Scrambler 500 4X4 Driving System Type Automatic PVT (Polaris Variable Transmission) Shift Type Side Lever (F/N/R) Gear Reduction, Reverse 4.74:1 Gear Reduction, Forward 3.06:1 Drive Ratio, Front 2:1 Drive Ratio, Final 2.77:1 Drive Chain 520 O-Ring Tir...

118 WARRANTY LIMITED WARRANTY Polaris Sales Inc., 2100 Highway 55, Medina, MN 55340, gives a SIX MONTH LIM- ITED WARRANTY on all components of the Polaris All Terrain Vehicle (ATV) against defects in material or workmanship. Polaris also gives a one year limited warranty on the final drive chain for...

120 WARRANTY ALL IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR- TICULAR PURPOSE) ARE LIMITED IN DURATION TO THE ABOVE SIX MONTH WARRANTY PERIOD. POLARIS FURTHER DISCLAIMS ALL EXPRESS WARRANTIES NOT STATED IN THIS WARRANTY. Some state...

121 WARRANTY Exported Vehicles EXCEPT WHERE SPECIFICALLY REQUIRED BY LAW, THERE IS NO WAR- RANTY OR SERVICE BULLETIN COVERAGE ON THIS VEHICLE IF IT IS SOLD OUTSIDE THE COUNTRY OF THE SELLING DEALER'S AUTHORIZED LOCA- TION.This policy does not apply to vehicles that have received authorization for ex...

122 WARRANTY Exported Vehicles How to Get Service If Purchased From A Private Party: If you purchase a Polaris product from a private citizen outside of the country in which the vehicle was originally purchased, all warranty coverage will be denied. Notice If your vehicle is registered outside of th...

124 MAINTENANCE LOG Present this section of your manual to your dealer each time your vehicle is serviced. This will provide you and future owners with an accurate log of maintenance and ser- vices performed. DATE MILES (KM) OR HOURS TECHNICIAN SERVICE PERFORMED / COMMENTS

126 INDEX A Air Filter . . . . . . . . . . . . . . . . . . . . . 80 All Wheel Drive Switch. . . . . . . . . . 27 All Wheel Drive System . . . . . . . 36-37 AWD Switch . . . . . . . . . . . . . . . . . . 36 AWD System . . . . . . . . . . . . . . . . 36-37 B Battery . . . . . . . . . . . . . . . . . ....