Polaris 300 4X4 - Manuals

5 KNOW YOUR VEHICLE As the operator of the vehicle, you are responsible for your personal safety, the safety of others, and the protection of our environment. Read and understand your owner's manual, which includes valuable informa- tion about all aspects of your vehicle, including safe operating pr...

6 SAFETY Safety Decals and Locations Warning decals have been placed on the ATV for your protection. Read and follow the instructions of the decals on the ATV carefully. If any of the decals depicted in this manual differ from the decals on your ATV, always read and follow the instructions of the de...

7 SAFETY Safety Decals and Locations Discretionary Warning WARNING• Never operate this ATV on HILLS steeper than 25 degrees 25 ° . To prevent flip-over on hilly terrain, when going up or down, use throttle and brakes gradually. • REVERSE operation can be dangerous even at low speeds. Steering become...

8 SAFETY Safety Decals and Locations “No Passenger” Warning WARNINGNEVER ride as a passenger.Passengers can cause a loss of control, resulting in SEVERE INJURY or DEATH. Age 16 Warning WARNINGOperating this ATV if you are under the age of 16 increases your chance of severe injury or death.NEVER oper...

9 SAFETY Safety Decals and Locations Clutch Cover Warning WARNINGNO STEP• Moving parts hazard under belt-clutch guard. To prevent serious injury, do not operate vehicle with guard removed. • Do not modify engine or clutch. Doing so can cause part failure, possible imbalance, and excessive engine RPM...

10 SAFETY Safe Riding Gear Always wear appropriate clothing when riding an ATV. Wear protective clothing for comfort and to reduce the chance of injury. Helmet Wearing a helmet can prevent a severe head injury. Whenever riding a Polaris vehicle, always wear a helmet that meets or exceeds established...

11 SAFETY Safe Riding Gear Eye Protection Do not depend on eyeglasses or sunglasses for eye protection. When- ever riding a Polaris vehicle, always wear shatterproof goggles or use a shatterproof helmet face shield. Polaris recommends wearing approved Personal Protective Equipment (PPE) bearing mark...

12 SAFETY Operator Safety Age Restrictions This vehicle is an ADULT VEHICLE ONLY. Operation is prohibited for anyone under 16 years of age. WARNING Failure to follow the warnings contained in this manual can result in severe injury or death.A Polaris ATV is not a toy and can be hazardous to operate....

13 SAFETY Operator Safety Safety Training ATV safety training is a top priority for Polaris. When you purchased your new ATV, your dealer instructed you on the authorized ATV RiderCourse sm available to you and your eligible family members. This training is included in the purchase price of your ATV...

14 SAFETY Operator Safety The following signal words and symbols appear throughout this manual and on your vehicle. Your safety is involved when these words and sym- bols are used. Become familiar with their meanings before reading the manual. The safety alert symbol , on your vehicle or in this man...

15 SAFETY Operator Safety • Read this manual and all labels carefully, and follow the operating procedures described. • Never operate an ATV without proper instruction. Take a training course. Purchasers of a new Polaris ATV and their eligible family members are entitled to take the ATV RiderCourse ...

18 SAFETY Operator Safety FOR MORE INFORMATION ABOUT ATV SAFETY, call the Con- sumer Product Safety Commission at 1-800-638-2772, or visit www.cpsc.gov, visit www.atvsafety.org, or call Polaris at 1-800-342- 3764. Equipment Modifications We are concerned for the safety of our customers and for the g...

34 FEATURES AND CONTROLS Switches Mode/Reverse Override Switch This vehicle is equipped with a reverse speed limiter system.To gain additional power while backing, depress the override switch. NOTE: The override switch also allows activation of All Wheel Drive in reverse, if the AWD switch is on. Th...

35 FEATURES AND CONTROLS Switches Engine Stop Switch Move the stop switch either left or right to the OFF position to stop the engine quickly. The engine will not start or run when the switch is off. NOTE: Both the main switch and the engine stop switch will shut off all electri- cal power to the ve...

36 FEATURES AND CONTROLS Throttle Lever Engine speed and vehicle move- ment are controlled by pressing the throttle lever. The throttle lever is spring loaded. Engine speed returns to idle when the lever is released.This ATV is equipped with Polaris Electronic Throttle Control (ETC), which is design...

37 FEATURES AND CONTROLS Brake Lever Squeeze the brake lever toward the handlebar to apply the front and rear brakes. These brakes are hydraulically activated disc type brakes that are activated by only one lever.Always test brake lever travel and master cylinder fluid level before riding. When sque...

38 FEATURES AND CONTROLS Parking Brake Locking the Parking Brake 1. Place the transmission in gear. 2. Squeeze and release the brake lever two or three times, then squeeze and hold. 3. Push the parking brake lock forward to engage the lock. 4. Release the brake lever.5. To release the parking brake ...

39 FEATURES AND CONTROLS Auxiliary Foot Brake The auxiliary brake system is intended to be used as a backup for the main brake system. Should the main system fail, use the auxiliary foot brake. The auxiliary foot brake is located on the inside of the right footrest. Operate this brake with your righ...

40 FEATURES AND CONTROLS Choke The choke assists in starting a cold engine. Refer to the engine starting procedure on page 50 for correct choke and throttle settings during start- ing. Fuel Tank Cap Remove the fuel tank cap to add fuel to the fuel tank. Use either leaded or unleaded gaso- line with ...

41 FEATURES AND CONTROLS Automatic Transmission Gear Selector The transmission gear selector is located on the right side of the vehicle. H: High Gear N: Neutral R: ReverseWhenever the ATV is left unattended, always place the transmission in gear and lock the parking brake. CAUTION Shifting gears wi...

42 FEATURES AND CONTROLS Recoil Starter If the battery is too weak to start the engine, use the recoil starter. Follow the starting procedures on page 50, cranking the engine with the recoil starter instead of the main key switch.1. Grasp the recoil starter rope handle tightly. 2. Pull slowly so you...

43 FEATURES AND CONTROLS All Wheel Drive (AWD) System (4X4 Models) The All Wheel Drive system is controlled by the AWD switch. When the switch is on 2X4, the ATV is in two-wheel drive at all times. When the switch is on AWD, the ATV is in all wheel drive and the AWD indicator light in the instrument...

44 FEATURES AND CONTROLS Instrument Cluster Your ATV is equipped with an instrument cluster that senses vehicle speed from the right front wheel. The instrument cluster measures distance in miles as well as hours of operation. It also includes a reverse speed limiter function that limits the ATV's s...

45 FEATURES AND CONTROLS Instrument Cluster Rider Information Center The rider information center is located in the instrument cluster. All seg- ments will light up for 3 seconds at start-up.1. Gear Indicator - This indicator displays gear shifter position. N = Neutral (Green) R = Reverse (Amber) 2....

46 OPERATION Fuel Safety WARNING Gasoline is highly flammable and explosive under certain conditions.• Always exercise extreme caution whenever handling gasoline.• Always refuel with the engine stopped, and outdoors or in a well ventilated area. • Do not smoke or allow open flames or sparks in or ne...

47 OPERATION Break-In Period The break-in period for your new Polaris ATV is the first ten hours of operation, or the time it takes to use the first two full tanks of gasoline. No single action on your part is as important as following the proce- dures for a proper break-in. Careful treatment of a n...

48 OPERATION Break-In Period Engine and Drivetrain Break-in 1. Fill the fuel tank with gasoline. See page 40.2. Check the oil level on the dipstick. See page 75. Add oil if neces- sary to maintain the level between the safe and add marks. 3. Drive slowly at first. Select an open area that allows roo...

49 OPERATION Pre-Ride Checklist WARNING If a proper inspection is not done before each use, severe injury or death could result. Always inspect the vehicle before each use to ensure it's in proper operating condition. Item Remarks Page Brake system/lever travel Ensure proper operation 37 86 Brake fl...

50 OPERATION Starting the Engine 1. Position the vehicle on a level surface.2. Place the transmission in neutral.3. Lock the parking brake. NOTE: The starter interlock will prevent the engine from starting if the trans- mission is in gear and the brake is not engaged. 4. Turn the fuel valve on.5. Si...

51 OPERATION Starting the Engine 8. Turn the ignition key past the ON position to engage the starter. Activate the starter for a maximum of five seconds, releasing the key when the engine starts. 9. If the engine does not start, return the key to the OFF position and wait five seconds before attempt...

52 OPERATION Hauling Cargo Your ATV has been designed to carry or tow a certain amount of load. Always read and understand the load distribution warning labels on the vehicle, and never exceed the weight capacities outlined in the specifi- cations section of the owner's manual and on the safety deca...

54 OPERATION Driving Safely Driving Procedures 1. Wear protective riding gear. See page 10.2. Sit upright with both feet on the footrests and both hands on the handlebars. 3. Start the engine and allow it to warm up. 4. Shift the transmission into gear.5. Check your surroundings and determine your p...

55 OPERATION Driving Safely Turning the Vehicle Your ATV is equipped with a solid rear axle, which drives both rear wheels equally at all times. This means that the wheel on the outside of the turn must travel a greater distance than the inside wheel when turning and the inside tire must slip tracti...

56 OPERATION Driving Safely Driving on Slippery Surfaces Whenever riding on slippery surfaces such as wet trails or loose gravel, or during freez- ing weather, follow these precautions:1. Slow down when enter- ing slippery areas. 2. Engage AWD before wheels begin to lose traction. 3. Maintain a high...

57 OPERATION Driving Safely Driving Uphill Whenever traveling uphill, follow these precautions:1. Drive straight uphill.2. Avoid steep hills (25 ° maximum). 3. Keep both feet on the footrests.4. Shift your weight uphill.5. Proceed at a steady rate of speed and throttle opening.6. Remain alert and be...

59 OPERATION Driving Safely Driving Downhill When driving downhill, follow these precautions:1. Shift your weight uphill.2. Drive straight downhill.3. Slow down.4. Squeeze the brake lever gradually. NOTE: Before operating your ATV, learn how to use the auxiliary brake for emergency situations (if si...

61 OPERATION Driving Safely Turning Around on a Hill (K-Turn) 1. Stop and lock the parking brake while keeping body weight uphill.2. Leave the transmission in forward and shut off the engine.3. Dismount on the uphill side of the vehicle, or on the left if the vehi- cle is pointing straight uphill. 4...

62 OPERATION Driving Safely Driving Through Water Your ATV can operate through water with a maximum recommended depth equal to the bottom of the footrests. Follow these procedures when operating through water:1. Determine water depths and current before crossing.2. Choose a crossing where both banks...

63 OPERATION Driving Safely Driving Through Water After running the vehicle in water, it's critical to have it serviced as out- lined in the maintenance chart. See page 68. The following areas need special attention: engine oil, transmission oil, front and rear gearcases, and all grease fittings. NO...

64 OPERATION Driving Safely Driving Over Obstacles Be alert! Look ahead and learn to read the terrain you're traveling on. Be constantly alert for hazards such as logs, rocks and low hanging branches. WARNING Severe injury or death can result if your vehicle comes in contact with a hid- den obstacle...

65 OPERATION Driving Safely Driving in Reverse Follow these precautions when operating in reverse:1. Always check for obstacles or people behind the vehicle. 2. Always avoid backing downhill. 3. Back slowly.4. Apply the brakes lightly for stopping. 5. Avoid turning at sharp angles. 6. Never open the...

66 OPERATION Driving Safely Parking on an Incline Avoid parking on an incline if possible. If it's unavoidable, follow these precautions:1. Stop the engine.2. Place the transmission in gear.3. Lock the parking brake.4. Always block the rear wheels on the downhill side.5. Turn the fuel valve off.

67 EMISSION CONTROL SYSTEMS Noise Emission Control System Do not modify the engine, intake or exhaust components, as doing so may affect compliance with U.S.A. EPA noise control requirements (40 CFR 205) and local noise level requirements. Operation on Public Lands in the U.S.A. Your Polaris vehicle...

68 MAINTENANCE Periodic Maintenance Chart Careful periodic maintenance will help keep your vehicle in the safest, most reliable condition. Inspection, adjustment and lubrication of important components are explained in the periodic maintenance chart.Inspect, clean, lubricate, adjust and replace part...

69 MAINTENANCE Periodic Maintenance Chart Maintenance Chart Key X Perform these operations more often for vehicles subjected to severe use. E Emission-related service (Failure to conduct this maintenance will not void the emissions warranty but may affect emissions.) Q Have an authorized Polaris dea...

73 MAINTENANCE Lubrication Guide Check and lubricate all components at the intervals outlined in the Periodic Maintenance Chart beginning on page 68. Items not listed in the chart should be lubricated at the General Lubrication interval. Item Lube Method Engine Oil Polaris Premium 4 Synthetic 0W-50 ...

74 MAINTENANCE Engine Oil Oil Recommendations Polaris recommends the use of Performance Synthetic 4-Stroke (PS-4) 0W-50 oil for this engine. PS-4 is a fully synthetic, high performance, multi-viscosity oil designed to provide the ultimate in lubrication per- formance and protection.Oil may need to b...

75 MAINTENANCE Engine Oil Oil Level The oil dipstick is located behind the recoil on the right side of the ATV.1. Position the vehicle on a level surface. 2. Place the transmission in neutral.3. Lock the parking brake. 4. Start the engine. Allow it to idle for 30 seconds. Stop the engine. 5. Remove ...

76 MAINTENANCE Oil and Filter Change Always change the oil and filter at the intervals outlined in the Periodic Maintenance Chart beginning on page 68. Always change the oil filter whenever changing oil.1. Position the vehicle on a level surface. 2. Place the transmission in neutral.3. Lock the park...

77 MAINTENANCE Oil and Filter Change 11. Place towels under the oil filter. Using an oil filter wrench, turn the filter counterclockwise to remove it. 12. Clean the filter sealing area on the engine. 13. Lubricate the filter o-ring. Check to make sure the o-ring is in good condition. 14. Install the...

78 MAINTENANCE Transmission Oil Always check and change the transmission oil at the intervals outlined in the Periodic Maintenance Chart beginning on page 68. Maintain the oil level at the bottom of the fill plug hole. See page 119 for the part numbers of Polaris products.The fill plug is located on...

79 MAINTENANCE Transmission Oil Oil Check 1. Position the vehicle on a level surface. 2. Place the transmission in gear.3. Lock the parking brake. 4. Remove the fill plug. Use a 15 mm wrench. 5. Check the oil level.6. Add oil as needed. Do not overfill. 7. Reinstall the fill plug. Torque to specific...

80 MAINTENANCE Transmission Oil Oil Change 1. Position the vehicle on a level surface. 2. Place the transmission in gear.3. Lock the parking brake. 4. Remove the fill plug. Use a 15 mm wrench. 5. Place a drain pan under the gearcase. 6. Remove the drain plug. Use a 15 mm wrench. 7. Allow the oil to ...

81 MAINTENANCE Front Gearcase (Demand Drive) Fluid Always check and change the demand drive fluid at the inter- vals outlined in the Periodic Maintenance Chart beginning on page 68. We recommend the use of Polaris Premium Demand Drive Hub Fluid. Use of other oils may result in improper operation of ...

82 MAINTENANCE Front Gearcase (Demand Drive) Fluid Fluid Check 1. Position the vehicle on a level surface. 2. Place the transmission in gear.3. Lock the parking brake. 4. Remove the fill plug. Use an 8 mm Allen wrench. 5. Check the oil level. 6. Add the recommended oil as needed to bring the level t...

83 MAINTENANCE Front Gearcase (Demand Drive) Fluid Fluid Change 1. Position the vehicle on a level surface. 2. Place the transmission in gear.3. Lock the parking brake. 4. Remove the fill plug. Use an 8 mm Allen wrench. 5. Place a drain pan under the gearcase. 6. Remove the drain plug. Use an 11 mm ...

84 MAINTENANCE Brake Fluid Check brake fluid levels for both brake systems before each ride. Always maintain brake fluid at the recommended level. Do not overfill. If the fluid level is low add DOT 4 brake fluid only. See page 119 for the part numbers of Polaris products. Under normal operation, the...

85 MAINTENANCE Brake Fluid Hand Brake The master cylinder is located on the left handlebar. Main- tain the fluid level 1/4" (6.3 mm) below the top edge of the master cylinder. Do not over- fill.1. Position the vehicle on a level surface. Make sure the handlebars are straight. 2. View the fluid l...

86 MAINTENANCE Brakes The front and rear brakes are hydraulic disc brakes, activated by moving the single brake lever toward the handlebar. The auxiliary foot brake is also hydraulic. Both brake systems are self-adjusting. Brake Inspections The following checks are recommended to keep the brake syst...

87 MAINTENANCE Toe Alignment Use the following procedure to check the toe alignment of the vehicle. The recommended toe alignment is 1/8" to 1/4" (3-6 mm) toe out.1. Place the handlebars in a straight-ahead position. 2. Place stands in front of the vehicle, per- pendicular to the rear tires....

88 MAINTENANCE Steering Assembly The steering assembly of the ATV should be checked periodically for loose nuts and bolts. If loose nuts and bolts are found, see your Polaris dealer for service before operating the vehicle. Side Panel Removal 1. Remove the seat.2. Grasp the top of the side panel and...

89 MAINTENANCE Tires Refer to the specifications section beginning on page 124 for recom- mended tire type, size and pressure. Tire Tread Depth Always replace tires when tread depth is worn to 1/8" (3 mm) or less. Front Wheel Hub Tightening Front wheel bearing tightness and spindle nut retention...

90 MAINTENANCE Tires Wheel Removal 1. Position the vehicle on a level surface. 2. Place the transmission in gear.3. Lock the parking brake. 4. Loosen the wheel nuts slightly.5. Place a suitable stand under the footrest frame to raise the wheel slightly off the ground. 6. Remove the wheel nuts.7. Rem...

91 MAINTENANCE Tires Wheel Installation 1. Place the wheel on the wheel hub with the valve stem toward the outside and the rotation arrows on the tire pointing toward forward rotation. 2. Install the wheel nuts finger tight. 3. Lower the vehicle to the ground.4. Torque the wheel nuts to specificatio...

92 MAINTENANCE Air Filter/Breather Filter 1. Position the vehicle on a level surface. 2. Place the transmission in gear.3. Lock the parking brake.4. Remove the seat. 5. Release the air box cover clips, and remove the air box cover. 6. Remove the air filter.7. Remove the sleeve from the filter. 8. Wa...

93 MAINTENANCE Lights Headlight Beam Adjustment The headlight beam can be adjusted slightly upward or downward. Use the following procedure to make the adjustment. 1. Position the vehicle on a level surface with the headlight approxi- mately 25 ft. (7.6 m) from a wall. 2. Place the transmission in n...

94 MAINTENANCE Lights When servicing a halogen lamp, don't touch the lamp with bare fingers. Oil from your skin leaves a residue, causing a hot spot that will shorten the life of the lamp. Headlamp Replacement 1. Turn the back of the headlight harness counterclockwise and pull the harness assembly a...

95 MAINTENANCE Recoil Housing Always drain the recoil housing after operating the vehicle in wet condi- tions. Drain the housing before storing the vehicle. Make sure the hous- ing is completely dry before reinstalling the drain plug.1. Place the transmission in gear.2. Lock the parking brake.3. Sto...

96 MAINTENANCE Spark Plugs Spark Plug Recommendations Refer to the specifications section beginning on page 124 for the recom- mended spark plug type and gap for your vehicle. Torque spark plugs to specification. Spark Plug Inspection Spark plug condition is indicative of engine operation. Check the...

97 MAINTENANCE Spark Plugs Spark Plug Inspection 4. Inspect the electrodes for wear and carbon buildup. Replace worn or fouled plugs. Verify that the gap is at specification before installation. 5. Reverse the procedure for spark plug installation. Torque to specification. Spark Plug Condition Norma...

98 MAINTENANCE Vehicle Immersion If it's impossible to take your ATV to a dealer before starting it, follow the steps outlined below.1. Move the vehicle out of the water. 2. Turn the fuel valve off.3. Check the air box. If water is present, dry the air box and replace the filter with a new filter. 4...

99 MAINTENANCE Spark Arrestor Use the following procedure to periodically purge accumulated carbon from the exhaust pipe/muffler.1. Position the vehicle on a level surface. 2. Place the transmission in neutral. 3. Lock the parking brake.4. Remove the arrestor clean-out plug from the bottom of the mu...

100 MAINTENANCE PVT System WARNING Failure to comply with the instructions in this warning can result in severe injury or death.Do not modify any component of the PVT system. Doing so may reduce its strength so that a failure may occur at a high speed. The PVT system has been precision balanced. Any...

101 MAINTENANCE PVT System PVT Drying There may be some instances when water is accidently ingested into the PVT system. Use the following instructions to dry it out before operating.1. Move the vehicle out of the water. 2. Remove the PVT drain plug. Use a 17 mm wrench, a flat screw- driver, or the ...

102 MAINTENANCE Battery Your ATV may have either a sealed battery, which requires little mainte- nance, or a conventional battery. A sealed battery can be identified by its flat covers on the top of the battery. A conventional battery has six filler caps on the top of the battery. Conventional Batte...

103 MAINTENANCE Battery Battery Removal 1. Place the transmission in gear. 2. Lock the parking brake. 3. Open the front cover.4. Disconnect the battery hold- down strap. 5. On conventional batteries, remove the battery vent tube. 6. Disconnect the black (nega- tive) battery cable first. 7. Disconnec...

104 MAINTENANCE Battery Battery Installation Using a new battery that has not been fully charged can damage the bat- tery and result in a shorter life. It can also hinder vehicle performance. Follow the battery charging instructions on page 106 before installing the battery.1. Ensure that the batter...

105 MAINTENANCE Battery Battery Storage Whenever the vehicle is not used for a period of three months or more, remove the battery from the vehicle, ensure that it's fully charged, and store it out of the sun in a cool, dry place. Check battery voltage each month during storage and recharge as needed...

106 MAINTENANCE Battery Battery Charging (Conventional Battery) 1. Remove the battery from the vehicle to prevent damage from leak- ing or spilled electrolyte during charging. See page 103. 2. Charge the battery with a charging output no larger than 1/10 of the battery’s amp/hr rating. Charge as nee...

107 MAINTENANCE Battery Battery Charging (Sealed Battery) NOTE: Always verify battery condition before and 1-2 hours after the end of charging. State of Charge Voltage Action Charge Time (Using constant current charger @ standard amps specified on top of battery) 100% 12.8-13.0 volts None, check at ...

108 MAINTENANCE Cleaning and Storage Washing the Vehicle Keeping your Polaris vehicle clean will not only improve its appearance but it can also extend the life of various components. The best and safest way to clean your Polaris vehicle is with a garden hose and a pail of mild soap and water. 1. Us...

109 MAINTENANCE Cleaning and Storage Washing the Vehicle If a high pressure water system is used for cleaning (not recommended), exercise extreme caution. The water may damage components and could remove paint and decals. Avoid directing the water stream at the follow- ing items: • Wheel bearings • ...

110 MAINTENANCE Cleaning and Storage Chrome Wheel Care (if equipped) Proper maintenance will protect chrome wheels from corrosion, pre- serve wheel life and ensure a "like new" appearance for many years. NOTE: Chrome wheels exposed to road salt (or salt in the air in coastal areas) are more ...

111 MAINTENANCE Cleaning and Storage Storage Tips Clean the Exterior Make any necessary repairs and clean the vehicle as recommended. See page 108. Stabilize the Fuel 1. Fill the fuel tank.2. Add Polaris Carbon Clean Fuel Treatment or Polaris Fuel Stabilizer. Follow the instructions on the container...

112 MAINTENANCE Cleaning and Storage Storage Tips Fluid Levels Inspect the fluid levels. Change fluids as recommended in the Periodic Maintenance Chart beginning on page 68. • Demand drive unit (front gearcase) • Transmission • Brake fluid (change every two years and any time the fluid looks dark or...

113 MAINTENANCE Cleaning and Storage Storage Tips Inspect and Lubricate Inspect all cables and lubricate all areas of the vehicle as recommended in the Periodic Maintenance Chart beginning on page 68. Battery Storage See pages 105-106 for storage and charging procedures. Storage Area/Covers Set the ...

114 MAINTENANCE Transporting the Vehicle Follow these procedures when transporting the vehicle.1. Stop the engine.2. Place the transmission in gear.3. Lock the parking brake.4. Turn the fuel valve off.5. Secure the fuel cap, oil cap and seat.6. Remove the key to prevent loss during transporting.7. A...

115 ADJUSTMENTS Camber and Caster The camber and caster are non-adjustable. Spring Adjustments The front and rear shock absorber springs are adjustable. Rotate the adjuster either clockwise or counterclockwise to increase or decrease spring tension. Always adjust both sides equally. NOTE: Accessory ...

116 ADJUSTMENTS Handlebars The handlebars can be adjusted for rider preference. 1. Loosen the four handlebar bolts.2. Adjust the handlebar to the desired height. NOTE: Be sure the handlebars do not contact the gas tank or any other part of the machine when turned fully to the left or right. 3. Torqu...

117 ADJUSTMENTS Carburetor Your Polaris ATV is calibrated at the factory for optimal performance at altitudes ranging from zero to 6,000 feet (1800 m) and temperatures of +40 degrees F. (4 degrees C.) or higher. Above 6000 feet (1800 m) the engine air/fuel mixture becomes overly rich and the engine ...

118 ADJUSTMENTS Throttle Cable Freeplay Adjust throttle cable freeplay at the handlebar.1. Locate the throttle cable adjuster at the handlebar. 2. Squeeze the end of the rub- ber boot and slide it far enough to expose the end of the inline cable adjuster. 3. Loosen the adjuster lock nut.4. Rotate th...

119 POLARIS PRODUCTS Part Number Description Engine Lubricant 2870791 Fogging Oil (12 oz. Aerosol) 2874865 Performance Synthetic 4-Stroke (PS-4) 0W-50 Oil (qt.) 2874866 Performance Synthetic 4-Stroke (PS-4) 0W-50 Oil (gal.) Gearcase / Transmission Lubricants 2873602 Premium AGL Synthetic Gearcase Lu...

120 TROUBLESHOOTING Drive Belt Wear/Burn Possible Cause Solution Driving onto a pickup or tall trailer in high range Use low range (if equipped). Starting out going up a steep incline Use low range (if equipped) or turn around using the K- turn (see page 60). Driving at low RPM or ground speed (3-7 ...

121 TROUBLESHOOTING Engine Doesn't Turn Over Engine Turns Over, Fails to Start Engine Backfires Possible Cause Solution Blown fuse Replace fuse Low battery voltage Recharge the battery to 12.8 VDC Loose battery connections Check all connections and tighten Loose solenoid connections Check all connec...

122 TROUBLESHOOTING Engine Pings or Knocks Engine Runs Irregularly, Stalls or Misfires Possible Cause Solution Poor quality or low octane fuel Replace with recommended fuel Incorrect ignition timing See your dealer Incorrect spark plug gap or heat range Set gap to specs or replace plugs Idle set too...

123 TROUBLESHOOTING Engine Stops or Loses Power Engine Overheating Possible Cause Solution Out of fuel Refuel, cycle key to ON position three times for 5 seconds each, then start Kinked or plugged fuel vent line Inspect and replace Water is present in fuel Replace with new fuel Overuse of choke Insp...

124 SPECIFICATIONS * Based on EU Directive 76/432/EC Hawkeye 2X4 Gross Vehicle Weight 930 lbs. (422 kg) Dry Weight 525 lbs. (238 kg) Fuel Capacity 4.5 gal. (17 l) Engine Oil Capacity 2 qts. (1.9 l) Transmission Oil 15.2 oz. (450 ml) Demand Drive Fluid 5 oz. (148 ml) Front Rack Capacity 70 lbs. (32 k...

125 SPECIFICATIONS Jetting Chart Clutching Chart Hawkeye 2X4 Tires/Pressure, Front 22x7-12 / 5 psi Tires/Pressure, Rear 22x10-12 / 5 psi Front Suspension MacPherson strut with 7" (18 cm) travel Rear Suspension Progressive rate with 8" (20 cm) travel Shock Adjustment CAM Brakes, Front Single-...

128 WARRANTY LIMITED WARRANTY Polaris Sales Inc., 2100 Highway 55, Medina, MN 55340, gives a SIX MONTH LIM- ITED WARRANTY on all components of the Polaris All Terrain Vehicle (ATV) against defects in material or workmanship. Polaris also gives a one year limited warranty on the final drive chain for...

129 WARRANTY WARRANTY COVERAGE AND EXCLUSIONS: LIMITATIONS OF WARRANTIES AND REMEDIES The Polaris limited warranty excludes any failures that are not caused by a defect in material or workmanship. This warranty does not cover accidental damage, normal wear and tear, abuse or improper handling. This ...

130 WARRANTY ALL IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR- TICULAR PURPOSE) ARE LIMITED IN DURATION TO THE ABOVE SIX MONTH WARRANTY PERIOD. POLARIS FURTHER DISCLAIMS ALL EXPRESS WARRANTIES NOT STATED IN THIS WARRANTY. Some state...

131 WARRANTY Exported Vehicles EXCEPT WHERE SPECIFICALLY REQUIRED BY LAW, THERE IS NO WAR- RANTY OR SERVICE BULLETIN COVERAGE ON THIS VEHICLE IF IT IS SOLD OUTSIDE THE COUNTRY OF THE SELLING DEALER'S AUTHORIZED LOCA- TION.This policy does not apply to vehicles that have received authorization for ex...

132 WARRANTY Exported Vehicles How to Get Service If Purchased From A Private Party: If you purchase a Polaris product from a private citizen outside of the country in which the vehicle was originally purchased, all warranty coverage will be denied. Notice If your vehicle is registered outside of th...

134 MAINTENANCE LOG Present this section of your manual to your dealer each time your vehicle is serviced. This will provide you and future owners with an accurate log of maintenance and ser- vices performed. DATE MILES (KM) OR HOURS TECHNICIAN SERVICE PERFORMED / COMMENTS

137 INDEX I Idle RPM Adjustment . . . . . . . . . . . 117 Immersion . . . . . . . . . . . . . . . . . . . . . 98 Instrument Cluster. . . . . . . . . . . . 44-45 J Jetting Chart, 2X4 . . . . . . . . . . . . . . 125 Jetting Chart, 4X4 . . . . . . . . . . . . . . 127 K Key Switch . . . . . . . . . . . ...