Polaris 2009 Victory Victory Vision- Manuals

3 INTRODUCTION Trademarks The following are registered trademarks of Polaris Industries Inc.POLARIS ® POLARIS THE WAY OUT ® VICTORY ® VICTORY MOTORCYCLES ® VICTORY VISION ® FREEDOM ® DUNLOP is a registered trademark of Dunlop Tire Corporation.LOCTITE is a trademark of Henkel Corporation.XM and its c...

4 INTRODUCTION Before You Ride Read your Rider’s Manual This Rider’s Manual contains information that is essential to safe riding and proper maintenance of your VICTORY VISION motorcycle. Anyone who uses the motorcycle (operators and passengers) must read the Rider’s Manual before riding. Carefully ...

5 TABLE OF CONTENTS BEFORE YOU RIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-36 REPORTING SAFETY DEFECTS . . . . . . . . . . . . . . . . . . . . . . 35 IDENTIFIC...

7 SAFETY Safety Safety Symbols and Terms Symbols And Terms Used In This Manual The following safety signal words and symbols appear throughout the Rider’s Manual . Your safety and the safety of others are involved when these words and symbols are used. Become familiar with their meanings before read...

8 SAFETY Saf ety Safe Riding Practices WARNING Improper use of this motorcycle can result in serious injury or death to you, your passenger and others. To minimize the risk of injury, read and understand the information contained in this section before operating the motorcycle. This section contains...

9 SAFETY Safety Safe Riding Practices • Your ability to safely operate the motorcycle depends on your judgment and your use of safe riding habits. Take a rider education course from the Motorcycle Safety Foundation or another qualified instructor. The course will help you develop or refresh your exp...

10 SAFETY Saf ety Safe Riding Practices The following design characteristics affect how you should ride the VICTORY motorcycle. • The motorcycle is designed for on-road use with one rider and one passenger. Do not exceed the Gross Vehicle Weight rating. See loading examples beginning on page 28 or t...

11 SAFETY Safety Safe Riding Practices Follow these general safe riding practices: • Before each ride, make the checks described in the Pre-Ride Checks section beginning on page 85. Operating the motorcycle without completing the pre-ride check may cause damage to the motorcycle or result in an acci...

12 SAFETY Saf ety Safe Riding Practices • The most common cause of accidents involving a motorcycle and an automobile is the automobile driver’s failure to see the motorcycle. Ride defensively, as if you are invisible to other motorists, even in broad daylight. Ride where you’re clearly visible to o...

13 SAFETY Safety Safe Riding Practices • Reduce your speed when: - The road has potholes or is otherwise rough or uneven.- The road has sand, dirt, gravel or other loose substances on it.- The road is wet, icy, or oily.- The road contains painted surfaces, manhole covers, metal grating, railway cros...

14 SAFETY Saf ety Safe Riding Practices • To maximize braking effectiveness, use the front and rear brakes together. Improper braking may cause loss of control or may not slow the vehicle in time to avoid a collision. Be aware of the following braking facts and practices: - The rear brake provides 4...

15 SAFETY Safety Safe Riding Practices • When approaching a curve, choose a speed and lean angle that allows you to pass through the curve in your own lane without applying the brakes. Excessive speed, improper lean angle or braking in a curve can cause loss of control. • Ground clearance is reduced...

16 SAFETY Saf ety Carrying A Passenger To carry a passenger safely, do the following: • Direct the passenger to hold on to you or to the passenger hand grips and to keep both feet on the passenger footrests. Do not carry a passenger who cannot place both feet firmly on the footrests. A passenger who...

17 SAFETY Safety Carrying Cargo Use the following guidelines when attaching cargo or accessories to the motorcycle. Failure to do so could result in loss of control. Where applicable, these guidelines also refer to the contents of any accessories. • Keep cargo and accessory weight to a minimum, and ...

18 SAFETY Saf ety Protective Apparel To decrease the risk of injury and increase riding comfort, wear protective riding apparel: • Wear a Department of Transportation (DOT) or SNELL approved helmet. Some state laws require that you wear an approved helmet. In accidents involving motorcycles, head in...

19 SAFETY Safety Saddlebags & Trunk Whenever operating a motorcycle with original equipment or accessory saddlebags: • Never ride at speeds exceeding 80 mph (120 kph). Depending on load and weather conditions, the maximum safe operating speed may be less than 80 mph (120 km/h). Saddlebags, combi...

20 SAFETY Saf ety Modifications Modifying the motorcycle by removing any equipment or by adding equipment not approved by VICTORY may void your warranty. Such modifications could make the motorcycle unsafe to ride and could result in severe injury to operator or passengers, as well as damage to the ...

21 SAFETY Safety Accessory Selection and Installation Because VICTORY cannot test and make specific recommendations concerning every accessory or combination of accessories sold, the operator is responsible for determining that the motorcycle can be safely operated with any accessories or additional...

22 SAFETY Saf ety Transporting The Motorcycle If you must transport the motorcycle, use a truck or trailer. Do not tow the motorcycle with another vehicle, as towing will impair the motorcycle’s steering and handling, which can cause loss of control.• Position and restrain the motorcycle so it remai...

23 SAFETY Safety Fueling Precautions For complete fueling procedure see page 110. Gasoline is highly flammable and can be explosive in certain conditions. Observe the following precautions when you refuel or service the fuel system: • Turn off the engine.• Open the fuel cap slowly.• Add fuel in a we...

24 SAFETY Saf ety Gasoline and Exhaust Precautions Gasoline and gasoline vapors are poisonous and can cause severe injury. • Do not swallow gasoline, inhale gasoline vapors, or spill gasoline on yourself or your clothes. • If you swallow gasoline, inhale more than a few breaths of gasoline vapor, or...

25 SAFETY Safety Periodic Maintenance Failure to perform safety maintenance as recommended can result in difficult handling and loss of control, which could result in serious injury or death. Always perform the safety maintenance procedures as recommended. Perform maintenance and repairs promptly as...

26 SAFETY Saf ety Periodic Maintenance • Keep the motorcycle clean. In addition to extending the service life and the original appearance of the motorcycle, a complete and thorough cleaning can reveal items in need of repair. • Keep equipment required by federal, state, and local laws in place and i...

27 SAFETY Safety Gross Vehicle Weight Rating (GVWR) Gross Vehicle Weight is the maximum allowable weight of the vehicle, and includes the total weight of the motorcycle, the operator, and the passenger. NEVER exceed the motorcycle’s Gross Vehicle Weight Rating. Exceeding the weight rating can reduce...

28 SAFETY Saf ety Loading Example 1 VICTORY VISION with no cargo or accessories. GVWR = 1414 lbs (641 kg) Item Weight Street Tour VICTORY VISION wet weight (full capacity all fluids) 844 lbs. (383 kg) 889 lbs. (403 kg) Operator - with recommended riding apparel 220 lbs. (100 kg) 220 lbs. (100 kg) Pa...

29 SAFETY Safety Loading Example 2 VICTORY VISION with cargo. GVWR = 1414 lbs (641 kg) Item Weight Street Tour VICTORY VISION wet weight (full capacity all fluids) 844 lbs. (383 kg) 889 lbs. (403 kg) Operator - with recommended riding apparel 220 lbs. (100 kg) 220 lbs. (100 kg) Passenger - with reco...

30 SAFETY Saf ety Loading Example 3 VICTORY VISION with cargo and accessories. GVWR = 1414 lbs (641 kg) Item Weight Street Tour VICTORY VISION wet weight (full capacity all fluids) 844 lbs. (383 kg) 889 lbs. (403 kg) Operator - with recommended riding apparel 220 lbs. (100 kg) 220 lbs. (100 kg) Pass...

31 SAFETY Safety Safety and Information Labels - VIN Decal Location of Vehicle Identification Number decal - on frame under rear console cover. See “Seat Removal / Installation” on page 190. VIN decal VIN Number Tire & Wheel Information Date of Manufacture (under rear console panel) Operator / F...

32 SAFETY Saf ety Safety and Information Labels - VECI Decal Location of Vehicle Emission Control Information decal - inside left saddlebag. VECI decal 3safety.fm Page 32 Tuesday, February 3, 2009 11:50 AM

33 SAFETY Safety Safety and Information Labels - NECI Decal Location of Noise Emission Control Information decal - inside left saddlebag. NECI decal (below VECI decal) Windshield decal 3safety.fm Page 33 Tuesday, February 3, 2009 11:50 AM

34 SAFETY Saf ety Safety and Information Labels - Tire Information & Cargo Decals Location of Tire Information decal - inside left saddlebag door Tire Information decal Cargo decals -inside bags (and trunk if equipped) 3safety.fm Page 34 Tuesday, February 3, 2009 11:50 AM

35 SAFETY Safety Reporting Safety Defects If you believe that your vehicle has a defect that could result in a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Polaris Industries in writing.If NHTSA rece...

36 SAFETY Saf ety NOTES visionownersmanual.book Page 36 Wednesday, February 13, 2008 4:31 PM

37 IDENTIFICATION I.D. Identification Numbers Vehicle Identification Number The Vehicle Identification Number is printed on the Manufacturer Information Decal located under the rear console cover on the frame. See “Seat Removal / Installation” on page 190.Record this number in the space provided on ...

38 IDENTIFICATION I.D . Engine Number The engine number is stamped into the right crankcase behind the rear cylinder (1). Record the number in the space provided on page 40. VECI / NECI & Tire Information Decals The Vehicle Emission Control Information (VECI), Noise Emission Control Information ...

39 IDENTIFICATION I.D. Ignition Key Number The ignition key number is stamped on the small metal tag (1) attached to the key ring. Remove the tag and record the number on page 40. Store the tag in a safe place.Additional keys can be copied from one of the original keys (VICTORY key blank required).I...

40 IDENTIFICATION I.D . Record important numbers below for reference: VIN Number Record Engine I.D. Record Ignition Key Number Record 4component identification.fm Page 40 Tuesday, February 3, 2009 12:54 PM

41 IDENTIFICATION I.D. Component Location - Left View Left Side View 1. Spark Plugs 2. Front Brake Caliper (left) 3. Gear Shift Pedal 4. Operator’s Footrest 5. Sidestand 6. Oil Drain Plug 7. Oil Filter 8. Passenger’s Footrest 9. Rear Brake Caliper 10. Diagnostic Connector (in left bag)11. Running Li...

42 IDENTIFICATION I.D . Component Location - Right View Right Side View 1. Drive Belt Guard 2. Drive Belt 3. Passenger’s Footrest 4. Drive Sprocket (under cover) 5. Speed Sensor (top of crankcase) 6. Engine Oil Fill Cap / Dipstick 7. Rear Brake Pedal 8. Operator’s Footrest 9. Front Brake Caliper (ri...

43 IDENTIFICATION I.D. Component Location - Front View Front View 1. Front Turn Signal (outer light, each side) 2. Wind Deflector (one each side) 3. Headlamp (high beam) 4. Headlamp (low beam) 5. Driving Lamp (or HID lamp if equipped) 6. Air Filter (front of frame) 7. Tiedown Loop (on frame) 8. Rear...

44 IDENTIFICATION I.D . Component Location - Rear View Rear View 1. Turn Signals (uppermost in lens) 2. Tail Lamps (3 each side; all tail bulbs are ON with lights) 3. Brake Lamps (four lower bulbs illuminate brightly when brake is applied with turn signal OFF; bottom two only with turn signal ON) 4....

45 IDENTIFICATION I.D. Component Location - Top View Top View 1. Windshield (radio antenna is under dash) 2. Left Mirror 3. Clutch Fluid Reservoir 4. Clutch Lever 5. Glove Compartment Door 6. Operator Seat 7. Passenger Seat 8. Left Saddlebag Latch 9. Trim Panel - Street Model (or Tour w/ Trunk Remov...

46 IDENTIFICATION I.D . Component Location - Rider’s View Rider’s View (See INSTRUMENTS, FEATURES, & CONTROLS for more information) 1. Speaker (left) 2. Fuel Gauge 3. Speedometer 4. Indicator Lamp Display 5. Information Display 6. Tachometer 7. Volt Meter 8. Speaker (Right) 9. Cruise Control Swi...

47 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Ignition Key The ignition key operates the ignition switch, fuel door (page 77) bag locks (page 81) and trunk lock (if equipped, page 82). Key position and function is described on the following pages.Keep the spare key (provided) in a safe place se...

48 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Ignition Switch Place the ignition key in the ignition switch to operate the following functions of the switch. IGNITION SWITCH FUNCTION OFF All electrical circuits are off. The ignition key can be removed. ON All electrical circuits are on. The ign...

49 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Instrument Cluster The instrument cluster includes the items listed on the following pages. The MODE button (page 62) is used to toggle through various functions, change unit display (mph to kph) and to reset all functions except the odometer and fu...

50 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Fuel Gauge The fuel gauge operates when the key is in the ON or ACC position. For most accurate readings, sit on the motorcycle and bring it to an upright position. Volt Meter The volt meter displays battery voltage being supplied to main electrical...

51 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Indicator Lamp Display The indicator lamps are located on the upper display in the center of the instrument panel. See the following pages for a description of each and its function. Information Display The information display, located below the ind...

52 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Clock 1. Turn the key to ON or ACC to view the clock. To change the setting, use the MODE button to toggle to the odometer. 2. Press and hold the MODE button until the hour segment flashes, then release the button. Tap the MODE button to advance to ...

53 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Gear Position The number of the current transmission gear is displayed with the key in the ON position and the Stop/Run switch in RUN. “N” displays in neutral. “R” displays in reverse (if equipped). Trip Odometer The trip odometer shows total miles ...

54 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Odometer The odometer displays total mileage of the vehicle in miles or kilometers. See “Trip Odometer” on page 53 to change the odometer display to trip meter. To Change Display Units To change the odometer display from English(miles & 12-hour ...

55 INSTRUMENTS, FEATURES, & CONTROLS Contr ols CONSOLE MOUNTED SWITCHES The console mounted switches are used to control the following features:• Handgrip Heaters (if equipped)• Hazard (emergency flashers)• Driving lamp (center headlamp)• Accessory switch location (blank) Refer to the following ...

56 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Hand Grip Heater Switch Press the rocker switch toward the Hi or Low position, depending on the amount of heat required. Press the rocker switch to the middle position to turn the grip heaters OFF. Hazard Switch (Emergency Flashers) The Hazard switc...

57 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Driving Lamp Switch When the ignition key is ON, the driving lamp switch operates the center headlamp or HID lamp (if equipped). The driving lamp is not controlled by the high / low beam switch. It is an additional low beam lamp that can be on at al...

59 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Check Engine & Turn Signal Indicator Lamps Check Engine This indicator illuminates momentarily when the ignition switch is ON and the engine is stopped. The light will illuminate if the tilt sensor has shut down the engine. If systems report abn...

60 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Oil Pressure & Low Fuel Indicator Lamps Engine Cruise Control Indicator Lamp Low Oil Pressure The Low Oil Pressure indicator illuminates when the ignition switch is in the ON position and the engine is not running. This means the indicator circu...

61 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Seat Heater Switches The seat heater switches (if equipped) are located on the seat under the left passenger hand grip.The driver and passenger seat heater settings are independently controlled. The front switch controls the driver’s seat and the re...

62 INSTRUMENTS, FEATURES, & CONTROLS Contr ols LEFT HANDLEBAR SWITCHMode Button The MODE button is located on the front side of the left handlebar switch.The MODE button is used to toggle through the various Information display items available, and to change the display from English (miles) to M...

63 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Headlamp High / Low Beam Switch To turn the headlamp on, turn the ignition key to ON and tap or press the start button. The headlamp high/low beam switch toggles the headlamp between high and low beam.• To activate the high beam, press the upper por...

64 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Windshield Adjustment Switch (Motorized) The motorized windshield adjustment switch changes the height (and angle) of the windshield. This button is active with the key in the ON or ACC position.• To move the windshield UP, press the upper portion o...

65 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Turn Signal Switch Use the turn signal switch to activate a turn signal. The key must be in the ON or ACC position.Turn signals automatically cancel after predetermined speed and distance conditions are met. To manually cancel a signal, move the swi...

66 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Turn Signal Momentary Feature The momentary signal feature is useful when passing or changing lanes. To use the momentary feature, push and hold the switch through at least one complete flash cycle (at least one second) to activate the feature. The ...

67 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Clutch Lever To disengage the clutch, pull the lever toward the handlebar. To engage the clutch, gradually release the lever. For smooth clutch operation, pull the lever quickly and release it gradually. Starter Interlock The motorcycle is equipped ...

69 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Engine Starter Button The engine starter button is used to start the engine, activate the headlight, and operate in reverse gear (if equipped).To start the engine, the engine stop/run switch must be in the RUN position. The transmission must be in n...

70 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Throttle Control Grip The throttle control grip controls the engine speed. To increase engine speed and power, twist the top of the throttle control grip toward you (A).To decrease engine speed and power, twist the top of the grip away from you (B)....

71 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Linked Braking System The front and rear brakes on the motorcycle are linked.Application of the front brake lever activates only the front brakes.Application of the rear brake pedal activates the rear brake caliper fully, while simultaneously activa...

72 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Front Brake Lever The front brake lever is located on the right handlebar.To apply the front brake, pull the lever toward the handlebar. As described on page 71 , the front brake lever activates only the front brake calipers.See “Braking” on page 12...

73 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Rear Brake Pedal The rear brake pedal is on the right side of the motorcycle. To apply the rear brake, press down on the rear brake pedal. As described on page 71, a small amount of front brake is also applied.See page 124 for braking procedures in ...

74 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Gear Shift Pedal The gear shift pedal is located on the left side of the motorcycle.• To shift to a lower gear, press down on the gear shift pedal. • To shift to a higher gear, lift up on the gear shift pedal. See page 114 through page 117 for prope...

75 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Foot Control Adjustment The brake pedal and shift pedal can be adjusted to one of three positions. The controls are in the center position as delivered from VICTORY.To move the controls to the front or rear position, do the following:1. Use a 6mm Al...

76 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Manual Windshield Adjustment If your motorcycle is not equipped with a motorized windshield, you can adjust it manually using the following procedure: 1. Stop the motorcycle and turn the key OFF.2. Remove the windshield trim panel (see page 184).3. ...

77 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Fuel Door Use the ignition key to unlock the fuel door. 1. Turn the key to the OFF position.2. Turn the handlebars full left. NOTE: Do not push the key down when unlocking the fuel door. 3. Turn the key counter-clockwise to release the fuel door lat...

78 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Fuel Cap Use the ignition key to unlock the fuel door.1. Turn the fuel cap counterclockwise to open.2. Set the cap in the holder while fueling.3. To install the cap, turn the fuel cap clockwise until seated. 4. Close the fuel door. The door is locke...

79 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Glove Compartment To OPEN the glove compartment: • Turn the handlebars to clear the door. Press and release the inner edge of the door. The door will open under spring pressure. To CLOSE the glove compartment: • Push the door firmly until latched, t...

80 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Sidestand The sidestand is located on the left side of the motorcycle. • To extend the sidestand, swing it out from the end until it is fully extended. Lean the motorcycle toward the sidestand until it firmly supports the motorcycle. • To retract th...

81 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Saddlebags The saddlebags can be locked with the ignition key. Lock the saddlebags when riding. To UNLOCK the saddlebag: 1. Insert key in bag lock and rotate clockwise to the unlocked position. 2. Remove the key.3. Press the bag lock to open the bag...

82 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Trunk Operation The trunk can be locked with the ignition key. Lock the trunk when riding. To UNLOCK the trunk: 1. Insert key in trunk lock and rotate key to the vertical position to unlock. 2. Remove the key.3. Press the trunk lock to open.4. Obser...

83 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Radio / Audio Systems Refer to the Audio section of this manual (beginning on page 251) for radio and accessory audio systems operation. Radio Panel visionownersmanual.book Page 83 Wednesday, February 13, 2008 4:31 PM

84 INSTRUMENTS, FEATURES, & CONTROLS Contr ols Tool Kit The tool kit can be used to perform most of the basic maintenance items and some of the general repairs.1. 4mm Ball Drive Allen Wrench2. 4mm / 6mm Open End Wrench3. 6mm Ball Drive Allen Wrench4. 8mm / 10mm Open End Wrench5. Combination Phil...

85 PRE-RIDE CHECKS Pr e-Ride Pre-Ride Checks Before Each Ride Perform the checks described in this section before each ride to keep your motorcycle in good operating condition. This is specially important before making a long trip or when removing the motorcycle from storage. You must be familiar wi...

86 PRE-RIDE CHECKS Pr e-Ride Check Electrical Equipment Turn the ignition key to the ON position and move the stop/run switch to RUN before performing the following electrical inspections. Return the ignition key to the OFF position after completing these inspections. If inspection of any electrical...

88 PRE-RIDE CHECKS Pr e-Ride Check Engine Oil Level A dipstick attached to the oil fill cap registers the engine oil level.1. With the transmission in neutral, start and run the engine for several minutes to bring it to operating temperature. 2. Shut the engine off and wait for 3-5 minutes.3. Stradd...

89 PRE-RIDE CHECKS Pr e-Ride 5. Remove the dipstick and read the oil level.6. If necessary, add or remove oil to bring the level into the area on the dipstick above the ADD mark and below the FULL mark. See “Engine Oil Specification” on page 248. WARNING Do not operate the motorcycle with the oil le...

90 PRE-RIDE CHECKS Pr e-Ride Fuel Level 1. Straddle the motorcycle on level ground and bring it to a vertical position. 2. Turn the ignition switch to the ON or ACC position and watch the fuel gauge (1) on the instrument panel. 3. Note the fuel level.4. Estimate your next fuel stop and plan accordin...

91 PRE-RIDE CHECKS Pr e-Ride Check Tires Tire Pressure • Normal riding warms the tires and increases the tire air pressure. For an accurate reading, check the tire pressure before you ride. Adjust tire pressure as required for the total weight of your intended load. Refer to the tire pressure table ...

92 PRE-RIDE CHECKS Pr e-Ride Check Brake Operation Pedal / Lever Movement • Squeeze the front brake lever and press the rear brake pedal to be sure both operate normally.The lever and pedal should feel firm and should hold pressure when applied with constant pressure. • Check the amount of front bra...

93 PRE-RIDE CHECKS Pr e-Ride Front Brake Fluid Level Inspection: 1. Stand the motorcycle upright on level ground.2. Turn the handlebars until the top of the front brake fluid reservoir is level. 3. View the brake fluid through the sight glass. The fluid should be clear and at a level above or near t...

94 PRE-RIDE CHECKS Pr e-Ride Rear Brake Fluid Level Inspection: 1. The rear brake fluid reservoir is located near the rear brake pedal, just inside the right lower leg fairing (view from front right side, see page 171). 2. Stand the motorcycle upright on level ground. View the brake fluid in the res...

95 PRE-RIDE CHECKS Pr e-Ride Brake Hoses, Hose Connections, & Brake Caliper Seals Inspect all brake hoses and brake hose connections for dampness or stains from leaking or dried brake fluid. Tighten any leaking connections to specified torque listed in the appropriate VICTORY service manual or c...

96 PRE-RIDE CHECKS Pr e-Ride Check Brake Pads Look at each front brake pad on both sides of the front disc at viewing angle (1).Look at each rear brake pad on both sides of the rear disc at viewing angle shown (2). You should see at least 1.5 mm of friction material on each front brake pad, and a mi...

97 PRE-RIDE CHECKS Pr e-Ride Check Throttle Control Grip and Cables Inspection: 1. Rotate the throttle control grip. It should rotate smoothly from its rest position to its completely open position and back again. It should return to its rest position quickly when released. 2. Throttle freeplay, the...

98 PRE-RIDE CHECKS Pr e-Ride Check Clutch System 1. Stand the motorcycle upright on level ground.2. Turn the handlebars until the top of the clutch fluid reservoir is level. 3. View the fluid through the sight glass. The fluid should be clear and at a level above or near the top of the sight glass. ...

99 PRE-RIDE CHECKS Pr e-Ride Check Front Suspension 1. Straddle the motorcycle and bring it to the vertical position. 2. Apply front brake and push down hard on the handlebars 3-4 times. The front suspension should operate smoothly and quietly. 3. Place the motorcycle securely on the sidestand and i...

100 PRE-RIDE CHECKS Pr e-Ride Check Steering Straddle the motorcycle and bring it to a vertical position. Turn the handlebars from stop to stop. The action should be smooth but not loose or interfered with by wires, hoses or control cables. visionownersmanual.book Page 100 Wednesday, February 13, 20...

101 PRE-RIDE CHECKS Pr e-Ride Check Rear Suspension Proper rear suspension adjustment is essential for the most comfortable ride and optimum safety. Check the rear shock absorber movement and air pressure to ensure the motorcycle has the proper amount of available suspension travel and ground cleara...

102 PRE-RIDE CHECKS Pr e-Ride Check Drive Belt The drive belt should fit tightly. Check drive belt tension (see page 147). The drive belt system must be cool, clean, and dry to accurately measure belt tension (deflection). Do not measure or adjust the drive belt when the belt or drive system is wet ...

103 PRE-RIDE CHECKS Pr e-Ride Check Sidestand Straddle the motorcycle and bring it to a vertical position. Move the sidestand to its stored (up) position, then to its fully extended (down) position and back again. It should move smoothly and quietly. When the sidestand is up, the return spring shoul...

104 PRE-RIDE CHECKS Pr e-Ride Check Sidestand Pad Wear The sidestand pad is a wear item and must be inspected before each ride and replaced if worn. The sidestand pad is designed to move the stand to the stored position if the stand is inadvertently left in the down position.Check the condition of t...

105 PRE-RIDE CHECKS Pr e-Ride Check Fasteners Visually inspect the entire motorcycle chassis and engine for loose, damaged or missing fasteners. Tighten loose fasteners to the proper torque (see the service manual for torque specifications not listed in this Rider’s Manual or contact an authorized V...

106 PRE-RIDE CHECKS Pr e-Ride Check Mirror Adjustment Check and adjust mirrors for proper rear view.Press the left, right, top, or bottom edge of the mirror as required to adjust. visionownersmanual.book Page 106 Wednesday, February 13, 2008 4:31 PM

107 OPERATION Oper at ion OPERATION Vehicle Operation The operation section of this manual describes how to ensure maximum performance and longevity through the proper care and operation of your motorcycle. NOTE: Even if you're an experienced motorcycle operator or passenger, read all of the safety ...

108 OPERATION Oper at io n Engine Break-In Period During the first 500 miles (800 kilometers), critical engine parts require special wear-in procedures so they seat and mate properly. Read, understand and use the following rules for operating the motorcycle during the first 500 miles (800 kilometers...

110 OPERATION Oper at io n Fueling Precautions Fuel the motorcycle with the sidestand down and on level ground. Use only the recommended fuel (see Fuel Specifications on page 247). Fill the fuel tank to a level just below the bottom of the fuel filler neck. Fuel door operation is on page 77. WARNING...

111 OPERATION Oper at ion Priming the Fuel System If the motorcycle has run completely out of fuel, prime the system before starting the engine.1. Fill the fuel tank.2. Turn the ignition key ON.3. Turn the engine stop switch to the RUN position (the fuel pump will run momentarily). 4. Wait for the p...

112 OPERATION Oper at io n Starting The Engine Starter Interlock A starter interlock system prevents the motorcycle from being started in gear unless the clutch lever is pulled in (clutch disengaged). Tilt Sensor A tilt sensor stops the engine if the motorcycle tips beyond 45 degrees to one side. Th...

113 OPERATION Oper at ion Starting The Engine (Cont.) 4. Place the sidestand in the UP (retracted) position.5. If the NEUTRAL light is not illuminated, shift the transmission to neutral. 6. Apply the front brake. Leave the throttle closed and press the starter button until the engine starts. Allow t...

115 OPERATION Oper at ion Shifting Gears (Recommended Shift Speeds) The following table shows the appropriate speeds at which to shift up or down to each gear. RECOMMENDED SHIFT SPEEDS Upshift (Acceleration) Gear Change Upshift Speed Downshift (Deceleration) Gear Change Downshift Speed 1st to 2nd 18...

117 OPERATION Oper at ion Shifting Gears (Downshifting) WARNING Downshifting at a speed in excess of the recommended downshift point may severely damage the transmission or cause the rear wheel to lose traction. It could also result in engine damage from running at excessive RPM. Reduce speed before...

119 OPERATION Oper at ion Accelerating To accelerate, open the throttle (roll the throttle control grip toward you). For even acceleration, open the throttle with a smooth, continuous motion. When you reach the recommended speed for upshifting, shift up one gear in accordance with the instructions f...

120 OPERATION Oper at io n Cruise Control Safety Read all of the important information below and on the following pages so you can safely operate the Cruise Control system. WARNING Improper operation of the cruise control could result in a loss of control and serious personal injury or death. WARNIN...

121 OPERATION Oper at ion Cruise Control Operation - Setting To set the cruise control (if equipped):1. Turn the cruise control power switch ON.2. Accelerate to the desired speed and press the SET button. This speed will be logged in memory. 3. The CRUISE indicator lamp on the display will illuminat...

122 OPERATION Oper at io n Cruise Control Operation - Resume, Accelerate RESUME Pressing the Resume button (RES) will reset the cruise to the memorized speed after braking or disengaging the cruise control with either brake, throttle, or clutch. NOTE: Turning the cruise control master switch OFF wil...

123 OPERATION Oper at ion Cruise Control Operation - Decelerate / Cancel DECELERATE Press (tap) and release the Decelerate (DEC) button to decrease speeds in approximately 1 mph increments. Press and hold the DEC button to reduce SET speed to desired speed, then release to enter a new SET speed. If ...

124 OPERATION Oper at io n Braking To slow the motorcycle with the brakes, close the throttle and apply the front and rear brakes evenly. As the motorcycle slows, either disengage the clutch or downshift each time your speed reaches a downshift point. Applying slightly more front brake than rear bra...

125 OPERATION Oper at ion Stopping The Engine Before stopping the engine, bring the motorcycle to a complete stop either in neutral or with the clutch disengaged. Once the motorcycle is at a complete stop, if it is not already in neutral, shift into neutral. To stop the engine, set the engine STOP/R...

126 OPERATION Oper at io n Parking the Motorcycle Choose a flat, firm surface to park the motorcycle. Brake to a complete stop, place the transmission in neutral, and stop the engine. Extend the sidestand fully, turn the handlebars to the left, and lean the motorcycle onto the sidestand. Make sure t...

127 OPERATION Oper at ion Reverse NOTICE: Do not attempt to engage or disengage the reverse system when the motorcycle is moving. NOTE: The starter system will not function if the reverse lever is engaged . If the reverse system fuse blows, the starter button will not function even if the reverse le...

128 OPERATION Oper at io n Reverse 1. Check the area behind and around the motorcycle for obstacles or people. Be aware that the front wheel may travel outward and require a larger operating area. 2. If already seated, dismount any passenger and make sure the motorcycle is stationary.3. Bring the mo...

129 MAINTENANCE Maintenance Maintenance Guidelines This section includes basic maintenance information for maintaining your motorcycle. Included is a Periodic Maintenance Interval chart, which outlines the regular service required to keep your motorcycle in the best operating condition. Regular serv...

130 MAINTENANCE M ainte nance Maintenance Safety Reminders Review all warnings below as well as any warnings contained within this manual that apply to a specific maintenance procedure and all information on maintenance product labels before attempting any maintenance or service procedure. WARNING C...

131 MAINTENANCE Maintenance WARNING Improper repairs or service can create unsafe conditions that can cause severe personal injury or death. If you have any doubt as to your ability to safely and correctly perform any procedure outlined in this Rider’s Manual , whether due to the lack of knowledge, ...

132 MAINTENANCE M ainte nance First Service Perform the first service after you’ve ridden your new motorcycle approximately 500 miles (800 kilometers). This maintenance is one of the most important services your motorcycle requires and should be performed by an authorized VICTORY dealer. Initial mai...

133 MAINTENANCE Maintenance Periodic Maintenance Table Component See Page ODOMETER READING IN MILES (KILOMETERS) 500 ( 800) 2500 ( 4000) 5000 ( 8000) 7500 ( 12,000) 10,000 (16,000) 12,500 (20,000) 15,000 (24,000) 17,500 (28,000) 20,000 (32,000) 22,500 (36,000) 25,000 (40,000) 27,500 (44,000) 30,000 ...

134 MAINTENANCE M ainte nance Periodic Maintenance Table ITEM See Page ODOMETER READING IN MILES (KILOMETERS) 500 (80 0) 2,500 ( 4000) 5,000 ( 8000) 7,500 ( 12,000) 10,000 ( 16,000) 12,500 ( 20,000) 15,000 ( 24,000) 17,500 ( 28,000) 20,000 ( 32,000) 22,500 ( 36,000) 25,000 ( 40,000) 27,500 ( 44,000)...

138 MAINTENANCE M ainte nance Maintenance Log Maintenance Performed Miles / Km Notes Performed By: visionownersmanual.book Page 138 Wednesday, February 13, 2008 4:31 PM

140 MAINTENANCE M ainte nance Engine Oil Level Check the engine oil level daily before each ride. See page 88. Engine Oil & Filter Change Change the engine oil at the intervals listed in the Periodic Maintenance Table on page 134.1. Start and run the engine until it reaches normal operating temp...

142 MAINTENANCE M ainte nance Engine Oil & Filter Change (Cont.) 11. Reinstall the oil fill cap. Start and run the engine until it reaches normal operating temperature. NOTE: After an oil change, the low oil pressure indicator remains illuminated longer than usual before going out. Do not rev th...

143 MAINTENANCE Maintenance Air Filter The standard VICTORY air filter element is a dry paper design and does not require the use of air filter oil. Inspect the air filter often if riding in unusually wet or dusty conditions.1. Remove the two air filter retaining screws.2. Pull the lower edge of the...

144 MAINTENANCE M ainte nance Drive Belt Condition Replace the drive belt if it is cracked or has broken teeth or frayed edges. No matter its condition, the drive belt should be replaced at periodic intervals (see the VICTORY service manual or an authorized VICTORY dealer). DO NOT attempt to check b...

145 MAINTENANCE Maintenance Drive Belt Wear Analysis Internal tooth cracks (hairline): OK to run, but monitor condition External tooth cracks: Replace belt Missing teeth: Replace belt Chipping (not serious): OK to run, but monitor condition Fuzzy edge cord: OK to run, but monitor condition Hook wear...

146 MAINTENANCE M ainte nance Drive Belt Tension Data Specifications are listed below for deflection and sonic tension. Sonic tension measurement requires Gates Sonic Tension Meter 507C or an equivalent. Drive Belt Deflection (Using PV-43532 Tension Gauge) Deflection 32mm ± 0.5mm Drive Belt Sonic Te...

147 MAINTENANCE Maintenance Drive Belt Tension Overview On new drive systems or belt, adjust belt tension after the first 500 miles (800 km). Adjust tension at each tire change thereafter.This procedure involves using the belt tension gauge, part no. PV-43532, which is designed specifically for meas...

148 MAINTENANCE M ainte nance Belt Tension Measurement Procedure 1. Safely elevate and support the motorcycle with the rear tire 1-2 inches off the floor (see page 200). 2. Place the transmission in neutral.3. Rotate the rear wheel in a forward direction until the valve stem is at the bottom. This i...

150 MAINTENANCE M ainte nance Determine The Tightest Spot 11. Repeat the above deflection measurements with the tire’s valve stem at the rear most position, top, and front most positions (90 degrees rotation each time), recording each measurement. 12. If the tightest measurement is not within the ra...

151 MAINTENANCE Maintenance Drive Belt Tension Adjustment 1. Move wheel to the tight spot location determined previously in Drive Belt Tension Inspection . 2. Loosen the rear axle nut (1) on the left side.3. Using a 13 mm deep socket, turn each axle adjuster nut (2) clockwise an equal amount to tigh...

152 MAINTENANCE M ainte nance Drive Belt / Rear Wheel Alignment 1. Look at the alignment reference marks (3) on each side of the swingarm and the marks (4) on the axle plates to verify proper wheel alignment. Axle plate mark to reference mark alignment must be the same on both sides. 2. If the marks...

153 MAINTENANCE Maintenance Rear Suspension Adjustment To provide the most comfortable ride and proper ground clearance, adjust air pressure in the rear shock absorber as specified on the decal (located in left saddlebag area) for total cargo and occupant weight.Follow these guidelines to adjust air...

155 MAINTENANCE Maintenance Swing Arm / Rear Axle Inspection 1. Sit in the operator’s seat and bounce the rear suspension a few times, checking for free movement without binding. Listen for abnormal noises. 2. Safely elevate and support the motorcycle with the rear tire 1-2 inches off the floor (see...

157 MAINTENANCE Maintenance Front Fork / Suspension Inspection Remove any dirt, debris, or bugs from the front fork inner tubes (1) to prevent seal damage from abrasion using warm water and a mild detergent.Inspect front forks for abnormal noise as outlined in Pre-Ride Inspection on page 99. Front F...

158 MAINTENANCE M ainte nance Steering Head Inspection Support the motorcycle with the front 1-2 inches off the floor (see page 200).Move the handlebars from full left to full right. Movement should be smooth without any rough spots.Alternately push and pull on the lower fork legs and feel for movem...

159 MAINTENANCE Maintenance Check Fuel System Components Fuel system hoses & connections - Inspect fuel hoses for cracks or damage. Inspect hose connections at the fuel tank and at the fuel rail for dampness or stains from leaks. Evaporative Emission Control System Visually inspect all evaporati...

160 MAINTENANCE M ainte nance Fast Idle A fast idle speed during warm up of between 1200 and 2000 RPM is automatically set by the EFI system Idle Air Control (IAC). Periodic adjustment is not required. Crankcase Breather Hose Inspect the crankcase breather hose for cracks or damage. Be sure the clam...

161 MAINTENANCE Maintenance Throttle Control Inspection With the engine OFF, rotate the throttle control grip fully open and then release it. 1. Repeat the twist and release process with the handlebars turned fully RIGHT and fully LEFT. 2. Verify that the throttle grip moves smoothly throughout the ...

162 MAINTENANCE M ainte nance Throttle Cable Freeplay Throttle cable freeplay, the amount of control grip movement from the rest position to the point of cable resistance, should be .080-.160 ″ (2-4 mm). Throttle Cable Freeplay Adjustment Procedure: Throttle Opening Cable Adjustment1. With the handl...

164 MAINTENANCE M ainte nance Cruise Control Cable (If equipped)1. Remove the triangular cover from the right side of the motorcycle by pulling straight outward at each corner to release the three tabs. 2. Inspect the throttle body end of the cruise control cable for fraying and be sure the end is s...

167 MAINTENANCE Maintenance Rear Brake Pedal Check the amount of rear brake pedal movement before it develops firm resistance. It should not move more than 3/8 inch (8mm) before pedal is firm.If pedal movement is excessive, contact your VICTORY dealer for service.Lubricate the rear brake pedal pivot...

168 MAINTENANCE M ainte nance Brake Fluid Precautions NOTICE: Brake fluid attacks painted surfaces and plastic parts. Always clean spilled brake fluid immediately with plenty of water and mild detergent. WARNING Do not operate the front brake with the reservoir cover removed. Fluid could overflow fr...

169 MAINTENANCE Maintenance Clutch Fluid Review Brake Fluid Precautions on page 168 . 1. Set the vehicle upright on a level surface and turn handlebars until top of reservoir is level. 2. View the fluid level through the sight glass.3. If level is low, check hoses, lines, and slave cylinder (on left...

170 MAINTENANCE M ainte nance Front Brake Fluid Level Review Brake Fluid Precautions on page 168. 1. Set vehicle upright on a level surface and turn handlebars until top of reservoir is level. 2. View the fluid level through the sight glass.3. If level is low, check brake pads for wear (page 96). If...

171 MAINTENANCE Maintenance Rear Brake Fluid Review Brake Fluid Precautions on page 168. 1. Set vehicle upright on a level surface and view the rear brake fluid reservoir through the right leg fairing. 2. The fluid level must be between the MIN and MAX level lines on the reservoir. 3. If level is lo...

172 MAINTENANCE M ainte nance Brake Disc Inspection & Cleaning Check brake pads for wear as outlined on page 96.Visually inspect front and rear brake discs for nicks, scratches, cracks, or other damage. Inspect the thickness of each disc in at least four different points around the disc. If any ...

173 MAINTENANCE Maintenance Reverse Idler Port Lubricate the reverse idler shaft and gear at every oil change (except the 500 mile/800 km break-in service). Refer to the Periodic Maintenance Table. We recommend the use of VICTORY Multi-Purpose Lubricant (P/N 2872863).1. Stop the engine and position ...

174 MAINTENANCE M ainte nance Gear Shift Pedal Check the shift pedal and linkage and tighten any loose fasteners.Lubricate the gear shift pedal pivot bushing with VICTORY All Purpose Grease (P/N 2872187) or a light spray lubricant at regular intervals in accordance with the Periodic Maintenance Tabl...

175 MAINTENANCE Maintenance Tire Condition Inspect the tire sidewalls, road contact surface, and tread base for cuts, punctures, and cracking. Replace damaged tires immediately (see your VICTORY service manual or an authorized VICTORY dealer). Tire Tread Depth Use a depth gauge or an accurate ruler ...

176 MAINTENANCE M ainte nance Tire Pressure Refer to the table below or the Tire Information Label on the motorcycle, located in the left saddlebag. Tire Pressure Table Tire ⇓ Load ⇒ Up to 200 lbs. (91 kg) Load 201 lbs. (92 kg) Max. Load Capacity FRONT: Dunlop Elite 3 130/70R18 63H 36 psi (248 kpa) ...

177 MAINTENANCE Maintenance Spark Plugs 1. Make sure the engine is at room temperature.2. Pull upward on the spark plug boot (not the wire) to remove. 3. To prevent debris from entering the spark plug hole, use compressed air to clean the area around the plugs before removing them. 4. Remove spark p...

178 MAINTENANCE M ainte nance Engine Compression An engine compression test can be performed in accordance with the Periodic Maintenance Interval table to monitor general engine condition. Refer to the VICTORY service manual or contact your VICTORY dealer to have a compression test performed. Exhaus...

179 MAINTENANCE Maintenance Battery Precautions The motorcycle uses a permanently sealed, maintenance-free battery. Do not remove the battery cap strip for any reason. Keep the battery connections clean and tight at all times. NOTICE: If your VICTORY motorcycle will not be used for a period of 6 wee...

180 MAINTENANCE M ainte nance Battery Charging 1. Following the charger manufacturer’s instructions, use a battery charger designed for use with 12-volt batteries. The charger should have a maximum charging rate of 1.8 amps. Charge the battery for approximately 10 hours at a rate of 1.8 amps. If you...

181 MAINTENANCE Maintenance Battery Removal 1. Turn handlebars fully right.2. Remove five belly pan screws (1) with a 6mm Allen wrench. 3. Remove screw (2) that joins the two side grills. NOTE FOR INSTALLATION: The grill bolt is placed in the FRONT hole; the center belly pan screw uses the rear hole...

183 MAINTENANCE Maintenance Battery Installation 1. Slide the battery into the battery box. Be sure tabs (1) at the bottom are engaged with slots (2) on inner battery box. NOTE: Replace damaged or missing foam pads. 2. Install battery into box with terminals facing forward. Tip the front battery box...

184 MAINTENANCE M ainte nance Windshield Trim Panel To remove the panel:1. Release corners of panel by lifting straight upward at each end (1). 2. Carefully slide panel toward windshield to disengage lower tabs (2) and remove the panel. 3. Unplug the antenna.4. To install, reverse the above steps.Wi...

185 MAINTENANCE Maintenance Fuse Box There are two fuse boxes under the windshield trim panel. Remove the trim panel (page 184) to access the fuses, auto-reset circuit breakers, and relays. Use the fuse puller provided in the tool kit to remove a fuse if necessary.. LEFT FUSE BOX RIGHT FUSE BOX (Dec...

186 MAINTENANCE M ainte nance Fuse Replacement 1. Remove the windshield trim panel (page 184). NOTE: The reverse system fuse is located on the left rear side of the motorcycle, under the seat . 2. Push center of darts upward and remove the fuse box cover panel(s). 3. Pull the tabs to release the cov...

187 MAINTENANCE Maintenance Headlamp Aim Inspection The headlamp should shine straight ahead. The top of the HIGH beam should be just below the height of the center of the headlamp lens, at a distance of 25 ft. (7.6 meters). The low beam pattern spreads farther right than the high beam (U.S. & C...

188 MAINTENANCE M ainte nance Headlamp Aim Adjustment The headlamp adjustment knob can be accessed through the opening in the headlamp housing mount under the windshield trim panel.1. Remove the windshield trim panel (page 184).2. Reach through the opening in the headlamp housing mount. 3. To LOWER ...

190 MAINTENANCE M ainte nance Seat Removal / Installation To remove the seat:1. Open the glove compartment door and fuel door.2. Lift the console trim panel straight upward at each corner to remove it. Do not tip the panel backward. 3. Remove the two seat bolts (4mm Allen). 4. Lift the front of the ...

191 MAINTENANCE Maintenance Trunk Removal To remove the trunk:1. Remove the seat (page 190).2. Disconnect the trunk wire harness (1).3. Remove the license plate and then remove the plate bracket by removing the two 4mm Allen screws (2). 1 2 visionownersmanual.book Page 191 Wednesday, February 13, 20...

192 MAINTENANCE M ainte nance Trunk Removal (Cont.) 4. Open the trunk and remove all contents.5. Remove the compartment cover by squeezing between the notches (1) and lift the cover away. 6. Remove three of the four trunk mount bolts (2) using a 13 mm socket and an extension on a suitable drive hand...

193 MAINTENANCE Maintenance Street Trim Panel Removal Trim Panel Removal 1. Remove seat (page 190).2. Remove license plate and plate bracket by removing the two 4mm Allen screws (1). 3. Lift edges of tail molding at indicated points in order (2), (3), then (4) to release tabs. NOTE: Lift tail moldin...

194 MAINTENANCE M ainte nance Street Trim Panel Installation Trim Panel Installation 1. Remove license plate bracket (page 191) and trunk (if equipped). 2. Lift edges of tail molding in the order outlined on page 193 for Street Trim Panel Removal. NOTE: Lift tail molding enough to provide clearance ...

195 MAINTENANCE Maintenance Headlamp Bulb Replacement To replace a headlamp bulb:1. Remove air filter (page 143). Pull sealing boot away from the back of the bulb(s) and housing. 2. Press the looped end of the wire clip bulb retainer and swing the end toward the center of the bulb to release it from...

196 MAINTENANCE M ainte nance Turn Signal Bulb Replacement (Front) To replace a front turn signal bulb:1. Remove the windshield trim panel (page 184).2. IMPORTANT: Disconnect the wire harness from socket BEFORE removing socket from the lens. Lift the lock tab on the connector and push connector off ...

197 MAINTENANCE Maintenance Tail / Brake Lamp / Turn Signal Bulb Replacement 1. Open saddlebags. (NOTE: Trunk or Street Panel removal is not necessary). 2. Remove license plate and plate bracket (1). Lift tail trim (“M” panel) (2) to disengage tabs (See “Street Trim Panel Removal” on page 193.) 3. R...

198 MAINTENANCE M ainte nance Electrical Precautions Be aware of the following DO’s and DON’Ts regarding the electrical system, in order to avoid disruption of electrical signals and possible system malfunction. DO’s • DO use ONLY genuine VICTORY parts and accessories designed for your model and fol...

199 MAINTENANCE Maintenance Electrical Precautions (Cont.) DON’Ts • DO NOT splice or cut any wires. • DO NOT tap in to any power or ground on the motorcycle unless specifically directed to do so by the VICTORY instructions that come with the kit. • DO NOT back-probe electrical connectors on the vehi...

200 MAINTENANCE M ainte nance Lifting The Motorcycle Some procedures such as tire removal, and steering, fork, swingarm, or axle inspection require lifting of the motorcycle to remove weight from the component being inspected. The motorcycle can be elevated by placing a stable, flat platform jack or...

201 MAINTENANCE Maintenance Fastener Torque NOTE: Refer to the service manual or an authorized VICTORY dealer for procedures and fastener torques not listed in this manual. Rear Axle Nut Front Axle Pinch Bolts Windshield Screws Front Brake Caliper Mounting Bolts Front Fender Front Axle52 lb-ft.71 Nm...

202 MAINTENANCE M ainte nance Troubleshooting For your personal safety, do not attempt inspection or repairs not fully described in this Rider’s Manual . Contact an authorized VICTORY dealer for service if you cannot determine the cause of a problem or if the inspection / repair exceeds your mechani...

203 MAINTENANCE Maintenance Troubleshooting Starter Motor Does Not Turn or Turns Slowly Possible Cause Possible Remedy/Action Engine Stop / Run Switch in Stop Position Place switch in RUN position. Battery Discharged Fully charge the battery (page 180). Battery Cables Loose or Corroded Inspect batte...

205 MAINTENANCE Maintenance Troubleshooting Shifting Difficulties or Hard to Find Neutral Brake Noise / Poor Brake PerformanceNOTE: Contact a VICTORY dealer if brake performance does not return after these inspections. Possible Cause Possible Remedy/Action Shift Linkage Bushings Dry Or Worn Lubricat...

206 MAINTENANCE M ainte nance Troubleshooting Battery Charging Rate Low or Battery Discharges Possible Cause Possible Remedy/Action Loose/Corroded Charging Circuit Connection Check / clean battery cable connections (page 181) and charging circuit connections (see dealer). Accessory Load Exceeds Char...

207 CLEANING Clean ing Pure VICTORY Products This section provides tips on the very best way to clean, polish and preserve every surface of your beautiful new VICTORY Motorcycle. We recommend the use of our new Pure VICTORY cleaning and polishing products and accessories, which have been specially d...

208 CLEANING Cleaning Washing the VICTORY Motorcycle Before Washing 1. Make sure exhaust pipes are cool. Cover each pipe opening with a plastic bag secured with a strong rubber band. 2. Check that the spark plugs, spark plug wire caps, oil fill cap and fuel caps are properly seated. 3. Rinse off as ...

209 CLEANING Clean ing Washing the VICTORY Motorcycle There are two totally different styles of motorcycle washing and there is a Pure VICTORY Polish product for each style. Standard “Bucket Wash” This is the conventional way to wash your motorcycle. We recommend the use of Pure VICTORY Bike Wash Co...

210 CLEANING Cleaning Washing the VICTORY Motorcycle Spray-Rinse-and-Ride Wash This is the new way to clean your VICTORY quickly and easily, then resume riding. Pure VICTORY Spray Rinse and Ride bike wash is safe and will not harm any surface that water won’t harm. If you clean your bike frequently,...

211 CLEANING Clean ing Quick Clean-Ups For quick clean-ups between washings, or when water is not available, use Pure VICTORY Spray & Wipe Instant Detailer, a complete spray-and-wipe product designed to clean and polish all surfaces. It works quickly and easily and is silicone-free so it leaves ...

212 CLEANING Cleaning Polishing the VICTORY Motorcycle Polished Aluminum Care When a VICTORY is new, the polished aluminum wheels, hand levers and shifter shine like chrome. Ultraviolet (UV) rays and oxidation will cause polished aluminum to grow dull, however, if it’s not properly polished and prot...

213 CLEANING Clean ing Polishing the VICTORY Motorcycle There are now two totally different styles of polishing or protecting your paint and chrome. Standard Method of Polishing Paint and Chrome Pure VICTORY Windshield, Paint and Chrome Polish is a unique formula designed to produce a glass-like shi...

214 CLEANING Cleaning Polishing the VICTORY Motorcycle Standard Method of Polishing Paint and Chrome 1. Shake the container well before using. 2. Apply with Pure VICTORY 100% Microfiber Wax Applicator in a circular motion or straight line to a clean surface. It can be applied in direct sunlight. 3. ...

215 CLEANING Clean ing Polishing the VICTORY Motorcycle Premium Polishing for Long-Lasting Protection This newer style of polishing paint and chrome utilizes the latest in high-quality polymer technology that provides the longest-lasting protection available in the polish industry today. Pure VICTOR...

216 CLEANING Cleaning Leather, Rubber and Vinyl Care For the finest leather care, use Pure VICTORY Leather, Vinyl & Rubber Conditioner, a unique, pleasantly scented formula of premium-quality polymers designed to restore luster and softness to vinyl, leather and rubber without making them slippe...

217 STORAGE Stor a ge Storage Reminders If you will not operate the motorcycle for several months, such as during the winter, store the motorcycle to prevent damage to the fuel system and the battery and to protect components from corrosion or deterioration. During storage you might use products tha...

218 STORAGE Stor a ge Storage Area Preparation Choose a dry, well-ventilated storage location, inside a garage or other structure if possible. The location should have a firm, flat surface and allow enough space for the motorcycle.To best preserve tire condition:• The storage area should have a rela...

219 STORAGE Stor a ge Clean and Protect the Motorcycle To prepare the motorcycle for storage, begin by cleaning it as outlined beginning on. Wax painted surfaces and polish chromed and other metal surfaces. Apply protectant to exposed rubber, vinyl, and plastic parts.Do not apply rubber protectant t...

220 STORAGE Stor a ge Fuel Stabilizer Using a mixture of fuel and the recommended amount of VICTORY Premium Carbon Clean Plus or other gasoline stabilizer, fill the fuel tank only to the top of the filler insert.Ride the motorcycle or start and run the engine for 15 minutes in a well ventilated area...

221 STORAGE Stor a ge Tire Inflation Inflate the tires to normal pressure (see page 176). Battery Care 1. Remove the battery (see page 181).2. Clean the battery terminals first with a wire brush to remove any loose deposits.3. Wash the posts and the ends of the battery cables with a solution of 1 pa...

222 STORAGE Stor a ge Park and Cover the Motorcycle Park the motorcycle in its storage location. Cover it with a genuine VICTORY motorcycle cover, or a cover made from a durable, breathable material designed for storage. Covering the motorcycle helps protect it from dust and other airborne materials...

223 STORAGE Stor a ge Maintenance During Storage Check and maintain normal air pressure in the tires (page 176) and battery voltage in the battery (page 180) during extended storage periods. visionownersmanual.book Page 223 Wednesday, February 13, 2008 4:31 PM

224 STORAGE Stor a ge Removal From Storage 1. Remove the cover and unlock the front forks (if locked).2. Check the tire pressure (page 176) and inflate the tires if necessary.3. Install the battery (page 183) and perform an electrical check (page 86).4. Wash and polish the motorcycle. See page 207.5...

225 WARRANTY Warr an ty Motorcycle Noise Regulation Tampering Tampering with noise control systems is prohibited. Federal law prohibits the following acts or causing thereof: • The removal or rendering inoperative by any person other than for the purposes of maintenance, repair, or replacement, of a...

226 WARRANTY W ar ranty Among those acts presumed to constitute tampering are:• Removal or puncturing of the muffler, baffles, header pipes, or any other component which conducts exhaust gasses. • Removal or puncturing of any part of the intake system.• Lack of proper maintenance.• Replacing any mov...

227 WARRANTY Warr an ty Noise Emission Warranty VICTORY Motorcycle Division warrants that this exhaust system, at the time of sale, meets all applicable U.S. EPA Federal noise standards. This warranty extends to the first person who buys this exhaust system for purposes other than resale, and to all...

228 WARRANTY W ar ranty Emissions Control System Warranty VICTORY MOTORCYCLES, Polaris Sales Inc. - Emission Control System Warranty Statement Your Warranty Rights and Obligations The California Air Resources Board and VICTORY Motorcycle Division, Polaris Sales Inc. (hereinafter VICTORY) are pleased...

229 WARRANTY Warr an ty Owner’s Warranty Responsibilities As the motorcycle owner, you are responsible for the performance of the required maintenance listed in your Rider’s manual. VICTORY recommends that you retain all receipts covering maintenance on your motorcycle, but VICTORY cannot deny warra...

233 WARRANTY Warr an ty lll. Limited Liability A. The liability of VICTORY under this Emission Control System Warranty is limited solely to the remedying of defects in material or workmanship by an authorized VICTORY motorcycle dealer at its place of business during customary business hours. This wa...

234 WARRANTY W ar ranty lV. Legal Rights THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. V. This warranty is in addition to the VICTORY Limited Motorcycle Warranty Vl. Additional Information Any replacement part that is equivalent in ...

235 WARRANTY Warr an ty VICTORY Motorcycle Warranty Policy Limited Warranty VICTORY Motorcycle Division, Polaris Sales Inc., P.O. Box 47700, Hamel, Minnesota 55340-9960, gives a ONE YEAR LIMITED WARRANTY on all components of the VICTORY Motorcycle against defects in material or workmanship. This war...

236 WARRANTY W ar ranty Warranty Coverage and Exclusions: Limitations of Warranties and Remedies The warranty excludes any failures that are not caused by a defect in material or workmanship. This warranty does not cover accidental damage, normal wear and tear, abuse or improper handling. This warra...

239 SPECIFICATIONS Spe cificat ions Model Year 2009 Specifications 2009 VICTORY VISION Dimensions Overall Length Street: 103.5 inches (262.9 cm) Tour: 104.9 inches (266.5 cm) Overall Width 45.2 inches (114.7 cm) Overall Height 58.5 inches (148.5 cm) Seat Height 26.5 inches (67.3 cm) Wheel Base 65.7 ...

247 SPECIFICATIONS Spe cificat ions Fuel Specification Your VICTORY motorcycle was designed to use unleaded gasoline with a minimum octane rating of 91 (R+M / 2 method) for best performance. Follow the guidelines below to ensure maximum performance, driveability, and engine service life. Use only un...

248 SPECIFICATIONS Spe cific at ion s Engine Oil Specification Polaris Recommends the use of VICTORY brand Semi-Synthetic 20W40 Motor Oil or equivalent motorcycle oil that is approved for use in wet clutch transmissions such as JASO MA rating. visionownersmanual.book Page 248 Wednesday, February 13,...

249 SPECIFICATIONS Spe cificat ions Service Manual Some procedures are beyond the scope of this manual. If you decide to perform service work that is not described here, please see your authorized VICTORY dealer to purchase the appropriate service manual. WARNING Some procedures provided in the Serv...

251 AUDIO SYSTEM OVERVIEW A udio Ov er view System Overview Introduction The following sections review how to use the AM/FM/WB audio system, CB radio, XM radio, auxiliary and iPod audio, and CD changer.Please note that your motorcycle may not be equipped with all of the components listed above. Comp...

252 AUDIO SYSTEM OVERVIEW A udio Ov er view Main User Interface 1 2 3 4 5 visionownersmanual.book Page 252 Wednesday, February 13, 2008 4:31 PM

253 AUDIO SYSTEM OVERVIEW A udio Ov er view Reference the main user interface graphic on previous page. 1. LCD screen : The LCD screen displays information for the active source. 2. Memory presets : Allows operator to store and recall up to 12 radio stations, directly-select any 1 of 10 CDs in CD ch...

254 AUDIO SYSTEM OVERVIEW A udio Ov er view 4. Power ON / OFF : Press the power button to turn the system on or off. NOTE: Ignition switch must be on or in the ACC position. 5. Source (SRC) - Mode : Press SRC to cycle through available sources, or exit mode menus. Press MODE to access the radio sett...

255 AUDIO SYSTEM OVERVIEW A udio Ov er view Lower Left-Hand Control 1. Volume control : Press to increase(+) or decrease(-) audio volume. Press and hold to rapidly increase or decrease volume. 2. Tuner control : Press to manually tune radio stations, CD or iPod tracks. Hold to automatically seek or ...

256 AUDIO SYSTEM OVERVIEW A udio Ov er view Upper Left-Hand Control* 1. PTT: “Push-to-Talk” Press and hold PTT button to transmit over CB radio. 2. Squelch : Press SQ(+) or SQ(-) to adjust CB radio channel reception sensitivity. 3. COM - ICOM select : Press COM to turn the CB on or off. Press and ho...

257 AUDIO SYSTEM OVERVIEW A udio Ov er view Rear Passenger Control 1. Rear PTT: “Push-to-Talk” Press and hold PTT to transmit over the CB radio only if CB radio is present. 2. Rear Volume control : Press VOL(+) to increase or VOL(-) to decrease rear passenger headset volume. visionownersmanual.book ...

258 AUDIO SYSTEM OVERVIEW A udio Ov er view Audio System Notes visionownersmanual.book Page 258 Wednesday, February 13, 2008 4:31 PM

259 AUDIO FEATURES Fea tures Audio Features System Power The ignition key must be in the ACC or ON position to use the audio system.With the key in the ACC or ON position and audio system OFF, the screen will display “VICTORY MOTORCYCLES”. NOTE: To prevent battery power loss, do not leave the key in...

260 AUDIO FEATURES Fea tur es Press the power button to turn the audio system on.When powered, the screen will display the active source(s). 1. Current audio source:• (U.S.) FM / AM / WB / iPod - AUX / XM / CD Changer • (Euro) FM / MW / LW / iPod - AUX / CD Changer 2. Station preset number (P1 - P12...

261 AUDIO FEATURES Fe at ur es Volume Control The driver can set the volume level for the front and rear speakers, turn the speakers off or on and mute the system audio level. Audio Mute Press and release MUTE to drop audio system volume. To resume volume to prior level, press and release: MUTE on L...

262 AUDIO FEATURES Fe at ur es Audio Volume Press and release (+) or (-) on console to raise or lower volume or VOL (+) or (-) on LH control Passenger Volume The passenger can control the rear headset music volume and the CB/ICOM volume when either are active.Press (+) or (-) on the passenger contro...

263 AUDIO FEATURES Fe at ur es Selecting Audio Sources Press and release S/E or SRC until desired source is active. FM source active: U.S. / European models AM source active: U.S. models only FM 92.5 ST AM 1130 visionownersmanual.book Page 263 Wednesday, February 13, 2008 4:31 PM

264 AUDIO FEATURES Fe at ur es WB (Weather) source active: U.S. models only AUX source active: U.S. / European models iPod source active: U.S. / European models* Source skipped if component not present. XM Radio source active*: U.S. models only* Source skipped if component not present.After 5 second...

266 AUDIO FEATURES Fe at ur es Audio Tuning FM, AM, WB, and XM stations can be selected by using the tuning function.Press and release TUNE (+) or TUNE (-) on the left control to locate stations in single-step increments. Press and hold TUNE (+) or TUNE (-) on the LH control to seek or scan for stat...

267 AUDIO FEATURES Fe at ur es Memory Presets The audio system features 12 user-defined presets that can be used to store favorite stations.To set a preset, select the desired source (FM, AM, WB, XM, MW, or LW).Use TUNE or seek/scan to locate radio station.Press and hold one of the console preset bu...

268 AUDIO FEATURES Fe at ur es Press S/E on the LH control, or the SRC button at any time to exit the system setting sub-menus and return to the default screen. NOTE: After 5 seconds of inactivity, the system will exit the setting menu and return to the default display. Bass Setting Press the consol...

269 AUDIO FEATURES Fe at ur es Treble Setting Press the console panel (+) or (-) button to increase or decrease audio treble level. Fader Setting* Press the console panel (+) or (-) button to attenuate the front and rear speaker output ratio. *Setting skipped when external speakers are off. visionow...

270 AUDIO FEATURES Fe at ur es External Speakers Press the console panel (+) or (-) button to turn the external speakers on or off. visionownersmanual.book Page 270 Wednesday, February 13, 2008 4:31 PM

271 AUDIO FEATURES Fe at ur es Automatic Volume Control (AVC) Press the console panel (+) or (-) button to set the Automatic Volume Control settings.AVC will lower or raise the speaker/ headset volume based on the ambient vehicle noise level.• AVC Off = No AVC. Volume will not adjust. • AVC Low = Le...

273 AUDIO FEATURES Fe at ur es ICOM Volume* Press the console panel (+) or (-) button to set the driver ICOM volume. *Setting skipped when COM system is not present. CB Volume* Press the console panel (+) or (-) button to set the driver CB volume. *Setting skipped when COM system is not present. Tun...

274 AUDIO FEATURES Fe at ur es CB LO/DX* Press the console panel (+) or (-) button to set the CB to either LOCAL (LO) or DISTANT (DX) mode.Reference the CB / ICOM section for more information. *Setting skipped when CB radio is not present. XM Display* Press the console panel (+) or (-) button to set...

276 AUDIO FEATURES Fe at ur es NOAA Weather Band (WB) When the WB source is selected, a total of 7 weather band channels are available.Weather band channels are broadcast by the National Oceanic and Atmospheric Administration (NOAA). NOAA operates more than 940 transmitters covering all 50 U.S. stat...

277 CB RADIO / ICOM CB/ICO M CB Radio / ICOM System Getting Started The ignition key must be in the ACCESSORY or RUN position to use the audio system.With the key in the ACCESSORY or RUN position and audio system OFF, the screen will display “VICTORY MOTORCYCLES”. NOTE: To prevent battery power loss...

278 CB RADIO / ICOM CB /ICOM Adjusting Channels When the CB radio system is active, CB and the active CB channel will be shown on the display screen. Press and hold COM on the upper LH control to access the CHANNEL ADJUST screen. CAUTION Some local governments restrict or prohibit the use of helmet-...

280 CB RADIO / ICOM CB /ICOM Push-to-Talk (PTT) Press and hold the PTT button on the upper left control to communicate over the CB radio. The passenger can communicate over the CB radio by pushing and holding the rear PTT button. Left Side ofTrunk visionownersmanual.book Page 280 Wednesday, February...

282 CB RADIO / ICOM CB /ICOM The squelch level can be adjusted between OPEN and CLOSED . When squelch is set to OPEN , no filtering occurs. Setting squelch to CLOSE blocks all signals, including strong signals.To set the squelch level, lower the squelch level until noise or static is heard. After he...

283 CB RADIO / ICOM CB/ICO M CB Radio Volume Setting (Driver)* *Setting skipped when CB radio is not present. Press and release the MODE button on the console panel to enter the audio system settings sub- menus.Continue to press and release the MODE button until the desired setting is shown on the d...

284 CB RADIO / ICOM CB /ICOM CB Radio Volume Setting (Passenger)* *Setting skipped when CB radio is not present. The passenger can control rear headset volume when the Entertainment, CB radio or ICOM is active (each volume setting is independently adjustable.)Press (+) or (-) on the passenger contro...

285 CB RADIO / ICOM CB/ICO M Press the console panel (+) or (-) button to set the CB to either LOCAL (LO) or DISTANT (DX) mode. Distant = Receiver sensitivity increased. Use for weaker signals. Static and noise levels increased. Local = Receiver sensitivity decreased. Use for stronger signals or in ...

286 CB RADIO / ICOM CB /ICOM CB Channels / Frequencies Ch. Freq. Ch. Freq. Ch. Freq. 1 26.965 8 27.055 15 27.135 2 26.975 9 27.065 16 27.155 3 26.985 10 27.075 17 27.165 4 27.005 11 27.085 18 27.175 5 27.015 12 27.105 19 27.185 6 27.025 13 27.115 20 27.205 7 27.035 14 27.125 21 27.125 22 27.225 31 2...

287 CB RADIO / ICOM CB/ICO M ICOM System Press and release ICOM on the upper LH control to activate the intercom system. When the intercom system is active, ICOM will be displayed on the console screen. VOX Break Setting The intercom is opened and closed using a voice operated switch (VOX). The volu...

290 CB RADIO / ICOM CB /ICOM ICOM Volume Setting (Passenger) The passenger can control the rear speaker volume only when the CB radio, ICOM, or rear headset speakers are active.Press (+) or (-) on the passenger control to raise or lower the rear speaker volume. Headset Receptacles A headset receptac...

291 CB RADIO / ICOM CB/ICO M Passenger Receptacle HEADSET RECEPTACLE (Left Side) visionownersmanual.book Page 291 Wednesday, February 13, 2008 4:31 PM

292 CB RADIO / ICOM CB /ICOM CB Radio / ICOM NOTES visionownersmanual.book Page 292 Wednesday, February 13, 2008 4:31 PM

293 AUX - iPod A ux/iPOD Overview Getting Started The ignition key must be in the ACCESSORY or RUN position to use the AUX or iPod function.With the key in the ACCESSORY or RUN position and audio system OFF, the screen will display “VICTORY MOTORCYCLES”. NOTE: To prevent battery power loss, do not l...

296 AUX - iPod Aux /iP OD 4. Disconnect the cable from the harness by carefully pushing up on the green tab. DO NOT ALLOW THE HARNESS TO DROP BACK THROUGH THE HOLE. 5. Install the desired input cable.6. Carefully push the sealing grommet back into the hole. AUX INPUT CABLE visionownersmanual.book Pa...

298 AUX - iPod Aux /iP OD iPod Tuning Press and release the TUNE (+) or TUNE (-) button on the lower LH control to move 1 track forward or 1 track backward.Press and release the TUNE (+) or TUNE (-) button on the lower LH control twice (double click) to move 10 tracks forward or 10 tracks backward. ...

299 XM Radio XM R adi o Overview XM Satellite Radio* XM Satellite Radio gives subscribers the power to choose what they want to hear - wherever and whenever they want it.• Over 170 digital channels• The most commercial-free music in satellite radio • Live concerts plus exclusive original programming...

300 XM Radio XM Radio NOTE: To prevent battery power loss, do not leave the key in the ACC position for long periods of time. It is recommended to have the engine running whenever using the audio system. Press the power button to turn the audio system on. Press and release the S/E button on the lowe...

301 XM Radio XM R adi o When the XM Radio is active, the console screen will display the XM radio channel, and either the artist, song title, channel name or category. If a category other than “ALL” is selected, the display will show the channel number and “C”. XM Reception If the XM radio is not re...

302 XM Radio XM Radio Activating XM Radio Service With the XM radio active, tune to channel 0 to view the XM ID Number on the screen. Record the XM ID number here: NOTE: The letters I, O, S, and F are not used. Your XM radio can be activated by calling XM Listener Care at 1-800-XM-Radio (1- 800-967-...

303 CD CHANGER CD Overview Getting Started The ignition key must be in the ACC or ON position to use the CD changer. With the key in the ACC or ON position and audio system OFF, the screen will display “VICTORY MOTORCYCLES”. NOTE: To prevent battery power loss, do not leave the key in the ACC positi...

304 CD CHANGER CD When the CD changer is active, the console screen will display the CD Player Cartridge 1. With ignition switch ON or in ACC, open the CD changer door. 2. Press the EJECT button.3. Remove the CD cartridge from the CD player. 4. Slide one of 10 trays out of the cartridge. Insert a CD...

305 CD CHANGER CD Selecting CDs The CD changer can hold up to 10 CDs. Each CD can be accessed by using the console preset buttons.Press and release one of the console preset buttons (P1 - P10) to access a CD. If no disc is located in the location pressed, the CD changer will move to the next highest...

306 CD CHANGER CD When a disc is found, the disc number (A), track number (B), and track time duration (C) will be shown on the console display screen. CD Track Selection Press and release the TUNE (+) or TUNE (-) button on the lower LH control to move forward or reverse 1 track on the CD.Press and ...

307 Inde x A Accelerate, Cruise Control . . . . . . . . . . . . . . . . . .122 Accelerating . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 Accessory Selection & Installation . . . . . . . . . . . . .21 Adjustment Foot Control . . . . . . . . . . . . . . . . . . . . . . . . . .75 Fr...