Polaris 2009 Victory Vegas Jackpot- Manuals

2 FOREWORD Thank you for choosing a VICTORY motorcycle! This owner’s manual contains information for the VEGAS JACKPOT and NESS SIGNATURE SERIES VEGAS JACKPOT model. Some of the photographs and illustrations used in the manual are generalizations, so your model may be slightly different than what is...

3 TABLE OF CONTENTS INTRODUCTION 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAFETY 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

4 INTRODUCTION Read the Owner’s Manual Your VICTORY owner’s manual contains information that’s essential to safe riding and proper maintenance of the motorcycle. Anyone who uses the motorcycle (operators and passengers) must read the owner’s manual before riding.Carefully read and understand the inf...

5 SAFETY Symbols and Terms Used in the Owner’s Manual The following safety signal words and symbols appear throughout the owner’s manual. Your safety and the safety of others are involved when these words and symbols are used. Become familiar with their meanings before reading the manual. ! The safe...

6 SAFETY Safe Riding Practices Improper use of this motorcycle can result in serious injury or death to you, your passenger and others. To minimize the risk of injury, read and understand the information contained in this section before operating the motorcycle. This section contains safety informat...

8 SAFETY Safe Riding Practices Follow these general safe riding practices: S Before each ride, make the checks described in the Pre-Operation Check section beginning on page 47. Operating the motorcycle without completing the pre-operation check may cause damage to the motorcycle or result in an acc...

9 SAFETY Safe Riding Practices S The most common cause of accidents involving a motorcycle and an automobile is the automobile driver’s failure to see the motorcycle. Ride defensively, as if you are invisible to other motorists, even in broad daylight. Ride where you’re clearly visible to other moto...

10 SAFETY Safe Riding Practices S Reduce your speed when: - The weather is windy, rainy or otherwise causing slippery or rapidly changing conditions.- The traffic is heavy, congested, not allowing sufficient space between vehicles or otherwise not flowing smoothly. - You are being passed in either d...

11 SAFETY Safe Riding Practices S Ground clearance is reduced when the motorcycle leans. Do not allow components to contact the road surface when leaning the motorcycle in a curve, as this could cause loss of control. S Retract the sidestand fully before riding. If the sidestand is not fully retract...

12 SAFETY Safe Riding Practices Protective Apparel To decrease the risk of injury and increase riding comfort, wear protective riding apparel. S Wear a Department of Transportation (DOT) or SNELL approved helmet. Some state laws require that you wear an approved helmet. In accidents involving motorc...

13 SAFETY Gross Vehicle Weight Rating (GVWR) Gross vehicle weight is the total combined weight of the motorcycle, the operator and the passenger. S The weight of the motorcycle includes the motorcycle and all of its fluids, any accessories and their contents, and any additional cargo on the motorcyc...

14 SAFETY Example 1: VEGAS JACKPOT / NESS JACKPOT with no accessories or cargo Gross Vehicle Weight Rating 1171 lbs (531 kg) Item Weight VEGAS JACKPOT with full capacity of all fluids 677 lbs (307 kg) Operator with recommended riding apparel 230 lbs (104 kg) Passenger with recommended riding apparel...

15 SAFETY Carrying Cargo Use the following guidelines when attaching cargo or accessories to the motorcycle. Where applicable, these guidelines also refer to the contents of any accessories. S Keep cargo and accessory weight to a minimum, and keep items as close to the motorcycle as possible to mini...

16 SAFETY Saddlebags When operating a motorcycle with original equipment or accessory saddlebags: S Never ride at speeds exceeding 80 mph (120 km/h). Depending on load and weather conditions, the maximum safe operating speed may be less than 80 mph (120 km/h). Saddlebags, combined with the lifting o...

17 SAFETY Transporting the Motorcycle If you must transport the motorcycle: S Use a truck or trailer. Do not tow the motorcycle with another vehicle, as towing will impair the motorcycle’s steering and handling, which can cause loss of control. S Position and restrain the motorcycle so it remains up...

18 SAFETY Accessory Selection and Installation Because VICTORY cannot test and make specific recommendations concerning every accessory or combination of accessories sold, the operator is responsible for determining that the motorcycle can be safely operated with any accessories or additional weight...

19 SAFETY Gasoline and Exhaust For complete fueling procedures, see page 64.Gasoline is highly flammable and can be explosive in certain conditions. Observe the following precautions when you refuel or service the fuel system: S Turn off the engine. S Use a well-ventilated area. S Open the fuel cap ...

20 SAFETY Maintenance Maintain the motorcycle according to the following requirements: S Before each ride, complete a pre-operation check as outlined beginning on page 47. Operating the motorcycle without completing the pre-operation check can cause damage to the motorcycle or result in an accident....

B D C A E 22 SAFETY Location of Safety and Vehicle Information Labels

23 SAFETY Location of Safety and Vehicle Information Labels Label content varies by model. The labels shown illustrate type and location only. Always refer to the label on your motorcycle for model-specific information. Location A (FUEL WARNING) Location B (MANUFACTURING INFORMATION) Location C (NOI...

25 SAFETY Location of Safety and Vehicle Information Labels Label content varies by model. The labels shown illustrate type and location only. Always refer to the label on your motorcycle for model-specific information. Location F FUSE and RELAY LOCATION (Under side cover, on side of fuse box cover)...

27 SAFETY Location of Safety and Vehicle Information Labels Label content varies by model. The labels shown illustrate type and location only. Always refer to the label on your motorcycle for model-specific information. Location G (TIRE SAFETY) Location H (EMISSION CONTROL INFORMATION) Canada Models...

28 SAFETY Reporting Safety Defects If you believe that your vehicle has a defect that could result in a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Polaris Industries in writing.If NHTSA receives si...

30 COMPONENT IDENTIFICATION Use the information on the following pages to identify and locate the major components of the VICTORY VEGAS JACKPOT motorcycle, including the vehicle and engine identification numbers, model number and ignition key number. HANDLEBAR AREA 1. Speedometer2. Front Brake Fluid...

1 2 3 7 11 6 10 12 13 15 16 18 19 20 21 22 14 8 4 5 17 9 31 COMPONENT IDENTIFICATION LEFT SIDE VIEW 1. Front Fork2. Front Turn Signal3. Headlight4. Air Filter5. Spark Plug (2)6. Ignition Switch7. Left Side Cover8. Battery (under side cover)9. Heated Grip Switch10. Taillight11. Rear Turn Signal12. Re...

17 15 9 10 11 14 13 12 1 2 5 6 4 3 8 7 16 32 COMPONENT IDENTIFICATION RIGHT SIDE VIEW 1. Drive Belt (under guard)2. Passenger Seat3. Seat Strap4. Operator’s Seat5. Side Cover6. Rear Shock Absorber (access through RH side cover)7. Front Turn Signal8. Front Fork9. Rear Brake Pedal10. Operator Foot Res...

33 COMPONENT IDENTIFICATION Vehicle Identification Number The vehicle identification number (VIN) is stamped into the front of the steering head and also appears on the certification label. You will need the vehicle identification number to title, register, license or insure the motorcycle, or to or...

34 COMPONENT IDENTIFICATION Engine Identification Number The engine identification number (A) is a combination of the engine model and serial numbers. The first 8 digits are the engine model number and the last 5 digits are the serial number.The engine serial number is stamped into the right crankca...

1. Off 3. P (Park) 1 2 3 2. On 35 INSTRUMENTS, FEATURES AND CONTROLS Ignition Key The ignition key operates the ignition switch and parking lights. Ignition Switch The ignition switch energizes the ignition, the lighting system, and all electrical switches and buttons. NOTE: Before starting the engi...

36 INSTRUMENTS, FEATURES AND CONTROLS Instrument Cluster The instrument cluster includes the speedometer (and the tachometer if installed as an accessory). 1. Speedometer 2. Odometer / Trip Odometer (See page 37)3. Odometer & Trip Odometer Toggle / Trip Odometer Reset (See page 37) Speedometer T...

37 INSTRUMENTS, FEATURES AND CONTROLS Odometer The odometer display shows total miles traveled in the window on the lower portion of the speedometer. Trip Odometer A trip odometer is included on the speedometer. The trip odometer shows total miles traveled since the trip odometer was reset. You can ...

38 INSTRUMENTS, FEATURES AND CONTROLS Indicator Lights Neutral Indicator (1) The neutral indicator illuminates when the transmission is in neutral, and the ignition key is ON. Headlight High Beam Indicator (2) The headlight high beam indicator illuminates when the headlight switch is set to high bea...

40 INSTRUMENTS, FEATURES AND CONTROLS Left Handlebar Controls Emergency Flasher Switch The emergency flasher switch activates and cancels the emergency flashers. When the emergency flashers are active, all of the turn signals flash. Press the top of the switch to activate the emergency flashers. Pre...

41 INSTRUMENTS, FEATURES AND CONTROLS Left Handlebar Controls Turn Signal Switch Operation The ignition key must be in the ON or PARK position and the engine stop/run switch must be in the ON position to operate the turn signals. Move the switch to the left to activate the left turn signals. Move th...

42 INSTRUMENTS, FEATURES AND CONTROLS Right Handlebar Controls Engine Stop/Run Switch The engine stop/run switch completes or interrupts the ignition, starter, and fuel pump circuits. To complete the circuits, allowing the engine to start and run, press the lower portion of the engine stop/run switc...

43 INSTRUMENTS, FEATURES AND CONTROLS Right Handlebar Controls Throttle Control Grip The throttle control grip controls the engine speed. To increase engine speed, twist the throttle control grip toward you; to decrease engine speed, twist the grip away from you. When you release the grip, it return...

45 INSTRUMENTS, FEATURES AND CONTROLS Fuel Cap The fuel cap must be opened and closed with the ignition key. Lift the key slot cover (1) on the cap and insert key. Turn clockwise while pushing down lightly to release latch and open the cap. To close the fuel cap, turn key clockwise and press down on...

46 INSTRUMENTS, FEATURES AND CONTROLS Side Covers Your motorcycle is equipped with two removable side covers. Remove the left side cover to access the battery. Remove the right side cover to access the fuses and the rear brake fluid reservoir.To remove right side cover, pull carefully at each dart l...

47 PRE-OPERATION CHECK To keep your VICTORY motorcycle in good operating condition, always perform the checks described in this section before each ride. This is especially important before making a long trip or when removing the motorcycle from storage. You must be familiar with the VICTORY motorcy...

48 PRE-OPERATION CHECK Electrical Equipment To perform a pre-operation check on the electrical equipment, set the ignition switch to the ON position. Set the ignition switch to the OFF position after completing the electrical equipment portion of the pre-operation check. Indicator Lights The low oil...

49 PRE-OPERATION CHECK Electrical Equipment Turn Signals Move the turn signal switch to the left. The front and rear left turn signals and the turn signal indicator light on the panel should flash. Push the switch button IN to cancel the turn signal. The turn signals and turn signal indicator should...

50 PRE-OPERATION CHECK Engine Oil Level A dipstick attached to the oil fill cap registers the engine oil level. We recommend the use of only VICTORY brand Semi-Synthetic 20W-40 Motor Oil or an equivalent oil designed for use with wet clutches (such as those with a JASO MA rating).1. With the transmi...

51 PRE-OPERATION CHECK Fuel Components Fuel Level 1. Straddle the motorcycle on level ground and bring it to a vertical position.2. Turn the ignition switch to the ON position and watch the fuel indicator light on the panel. NOTE: The light will stay on if less than .8 gallons (3.08 liters) remains ...

52 PRE-OPERATION CHECK Tires Tire Pressure Normal riding warms the tires and increases the tire air pressure. For an accurate reading, check the tire pressure before you ride. Adjust tire pressure as required for the total weight of your intended load. Refer to the tire pressure table on page 119. T...

53 PRE-OPERATION CHECK Brakes Front Brake Lever Movement Squeeze the front brake lever toward the handlebar and release it. It should move freely and smoothly and should return to its rest position quickly when released. You should feel a firm resistance in the lever within the first 3/4-inch (19 mm...

54 PRE-OPERATION CHECK Brakes Rear Brake Pedal Press and release the rear brake pedal. It should move freely and smoothly and should return to its rest position quickly when released. You should feel a firm resistance within the first 8 mm of pedal travel. If the brake pedal travels too far before b...

55 PRE-OPERATION CHECK Brakes Rear Brake Fluid Level 1. To check the rear brake fluid level, remove right side cover. Straddle the motorcycle and bring it to a vertical position. 2. View the brake fluid through the reservoir. The fluid should be clear and at a level between minimum (MIN) and maximum...

2-4 mm 56 PRE-OPERATION CHECK Brakes Hoses and Connections Inspect all brake hoses and connections for dampness or stains from leaking or dried fluid. Tighten any leaking connections and replace components as necessary. Refer to the Victory Service Manual for torque values of fasteners or contact yo...

57 PRE-OPERATION CHECK Clutch Mechanical Clutch 1. Squeeze the clutch lever toward the handlebar and release it. It should move freely and smoothly and should return to its rest position quickly when released. 2. Clutch lever freeplay is the amount of clutch lever movement from the rest position to ...

60 PRE-OPERATION CHECK Sidestand Straddle the motorcycle and bring it to a vertical position. Move the sidestand (1) to its stored (up) position, then to its fully extended (down) position and back again. It should move smoothly and quietly. When the sidestand is in its stored position, the sidestan...

61 OPERATION The operation section describes how to operate your VICTORY motorcycle for best performance and longevity. Important areas covered include: S Engine Break-in Period S Fueling and Fill Height S Starting the Engine S Shifting Gears S Accelerating S Braking S Stopping the Engine S Parking ...

62 OPERATION Engine Break-in Period During the first 500 miles (800 kilometers), critical engine parts require special wear-in procedures so they seat and mate properly. Read, understand and use the following rules for operating the motorcycle during the first 500 miles (800 kilometers) to ensure yo...

64 OPERATION Engine Break-in Period Fueling and Fill Height Fuel the motorcycle with the sidestand down and on level ground. Use only the recommended fuel (see Fuel Specifications on page 161). Fill the fuel tank to a level just below the bottom of the fuel filler insert. • Do not allow gasoline to ...

65 OPERATION Engine Break-in Period Priming the Fuel System If the motorcycle has run completely out of fuel, prime the system before starting the engine: Turn the ignition switch to the ON position. Toggle the engine stop/run switch from the STOP position to the RUN position. Allow the fuel pump to...

66 OPERATION Engine Break-in Period Starting the Engine 4. Set the engine stop/run switch to the RUN position. You should hear the fuel pump run momentarily as it pressurizes the fuel system. NOTE: If the motorcycle was run completely out of fuel, prime the system as instructed on page 65. 5. Leavin...

67 OPERATION Shifting Gears The clutch must be fully disengaged (clutch lever pulled completely in toward the handlebars) before you attempt to shift gears. Forced shifting (shifting without the clutch disengaged) may damage the engine, transmission and drive train, causing loss of control of the mo...

68 OPERATION Shifting Gears 1. To engage first gear, start the engine (see Starting the Engine on page 65).2. With the engine at idle speed, engage the front brake (squeeze the brake lever) and disengage the clutch (squeeze the clutch lever). 3. Push the shift pedal down until you feel it stop in fi...

69 OPERATION Shifting Gears • Downshifting at a speed in excess of the recommended downshift point may severely damage the transmission or cause the rear wheel to lose traction. It could also result in engine damage from running at excessive rpm. Reduce speed before downshifting and do not downshift...

70 OPERATION Accelerating To accelerate, open the throttle (roll the throttle control grip toward you). For even acceleration, open the throttle with a smooth, continuous motion. When you reach the recommended speed for upshifting, shift up one gear according to the instructions in Shifting Gears, p...

71 OPERATION Braking To slow the motorcycle with the brakes, close the throttle and apply the front and rear brakes evenly. As the motorcycle slows, either disengage the clutch or downshift each time your speed reaches a downshift point. Applying slightly more front brake than rear brake generally g...

72 OPERATION Stopping the Engine Before stopping the engine, bring the motorcycle to a complete stop either in neutral or with the clutch disengaged. Once the motorcycle is at a complete stop, if it is not already in neutral, shift into neutral. To stop the engine, set the engine stop/run switch to ...

73 OPERATION Parking the Motorcycle When parking the motorcycle, choose a flat, firm surface. Bring the motorcycle to a complete stop and, with the transmission in neutral, stop the engine. Fully extend the sidestand, turn the handlebars to the left, and lean the motorcycle to the left until the sid...

75 MAINTENANCE This section includes information for maintaining your VICTORY motorcycle. It includes the Periodic Maintenance Interval tables, a guide to keeping your motorcycle in the best operating condition. Regular service increases the durability, safety, and dependability of your motorcycle, ...

76 MAINTENANCE Initial Maintenance Perform the initial maintenance after you’ve ridden your new motorcycle 500 miles (800 kilometers). This maintenance is one of the most important services your motorcycle requires and should be performed by an authorized VICTORY dealer. Initial maintenance includes...

5000 (8 ,000) 7,500 (12,000) 2,500 (4 ,000) 500 (800) 10,000 (16,000) 12.500 (20,000) 15,000 (24,000) 17,500 (28,000) 20,000 (32,000) 22,500 (36,000) 25,000 (40,000) 27,500 (44,000) 30,000 (48,000) 32,500 (52,000) 35,000 (56,000) 37,500 (60,000) 40,000 (64,000) 42,500 (68,000) 45,000 (72,000) 47.500...

80 MAINTENANCE MAINTENANCE RECORD MAINTENANCE PERFORMED MILES / KM NOTES PERFORMED BY:

82 MAINTENANCE Engine Oil Change Engine Oil and Oil Filter A hot engine or hot exhaust pipes can be hazardous. The engine and exhaust pipes are hot for some time after the engine is stopped. Touching the engine or exhaust pipes while hot can cause serious burns. Allowing flammable materials to conta...

83 MAINTENANCE Engine Oil Change Engine Oil and Oil Filter 8. Make sure the new oil filter gasket is properly seated in the oil filter, and apply a thin film of clean engine oil to the gasket. Screw the new filter on until the gasket contacts the filter mounting plate. Tighten the filter by hand an ...

84 MAINTENANCE Engine Oil Engine Oil Level 1. With the transmission in neutral, start and run the engine for several minutes. 2. Shut the engine off and wait for 3-5 minutes.3. With the engine at normal operating temperature, straddle the motorcycle on level ground and bring it to a vertical positio...

85 MAINTENANCE Inspect Air Filter The standard VICTORY air filter element is a dry, treated paper design and does not require the use of air filter oil. NOTE: Inspect the air filter often if riding in unusually wet or dusty conditions. 1. Remove the air filter access cover and air filter element usi...

86 MAINTENANCE Drive Belt Drive Belt Condition Replace the drive belt if it is cracked or has broken teeth or frayed edges. No matter its condition, the drive belt should be replaced at periodic intervals (see the VICTORY Service Manual or an authorized VICTORY dealer). DO NOT attempt to check belt ...

88 MAINTENANCE Drive Belt Drive Belt Tension 1. Place the transmission in neutral and lift the rear wheel off the ground with an appropriate motorcycle lift or a block of wood or steel placed securely under the frame. Care should be taken to be sure the motorcycle will not tip or fall while elevated...

89 MAINTENANCE Drive Belt Drive Belt Tension 4. Place the base of the tension gauge bracket squarely against the lower strand of the drive belt halfway between the front and rear drive sprockets. Use the tape measure or ruler and record the position of the base of the tension gauge bracket. This pos...

90 MAINTENANCE Drive Belt Drive Belt Tension Adjustment Care should be taken to be sure the motorcycle will not tip or fall while elevated. Severe personal injury or death may occur if the motorcycle tips or falls. WARNING NOTE: Before adjusting drive belt tension, inspect wheel alignment. (See Alig...

91 MAINTENANCE Rear Wheel Alignment A skewed rear axle can damage the drive belt, causing belt failure and loss of control of the motorcycle. WARNING 1. Bring the motorcycle to a vertical position.2. Place the transmission in Neutral and lift the rear wheel off the ground with an appropriate motorcy...

92 MAINTENANCE Rear Wheel Alignment (cont.) NOTE: Turn the axle adjusters about 1/16 of a turn at a time and monitor wheel alignment as you proceed. 5. On screw style adjusters : Use a 17mm wrench to loosen lock nut (4), then an 8mm hexagonal wrench to turn the axle adjuster screws (5). On nut style...

93 MAINTENANCE Rear Wheel Alignment (cont.) 9. Recheck drive belt tension and alignment to be sure it is correct after tightening the axle. 10. If alignment is incorrect, repeat steps 4-8.11. Pump rear brake pedal several times to reset brake pad distance. 12. Carefully lower the motorcycle and safe...

94 MAINTENANCE Rear Suspension Inspect Rear Shock Absorber Pre-Load (Ride Height) This procedure involves using the shock absorber preload wrench PV-43507, a special spanner tool available from your dealer. The tool is designed specifically for adjusting shock spring preload on your motorcycle. Prel...

95 MAINTENANCE Rear Suspension InspectRear Shock Absorber Preload (Ride Height) Measure from floor to rearmost flat section of right side frame cradle. Ride Height Specification: VEGAS JACKPOT 4 3/4 ″ (120 mm) ¦ 3mm ( ¦ 1/8 ″ ) (Motorcycle loaded in upright position) Floor Frame Cradle Operator Pass...

96 MAINTENANCE Rear Suspension Adjust Rear Shock Absorber Preload (Ride Height) To adjust the shock absorber spring pre-load:1. Rest the motorcycle on the sidestand. Remove the right side cover (page 46). 2. Remove the fuse box from right panel by lifting upward on the tab at the rearward end while ...

98 MAINTENANCE Rear Suspension Care should be taken to be sure the motorcycle will not tip or fall while elevated. Severe personal injury or death may occur if the motorcycle tips or falls. WARNING Inspect Swing Arm and Rear Axle 1. Sit in the operator’s seat and slowly bounce the rear suspension a ...

99 MAINTENANCE Front Suspension and Steering Care should be taken to be sure the motorcycle will not tip or fall while elevated. Severe personal injury or death may occur if the motorcycle tips or falls. WARNING Front Forks 1. To check the front suspension, straddle the motorcycle and bring it to a ...

100 MAINTENANCE Front Suspension and Steering Care should be taken to be sure the motorcycle will not tip or fall while elevated. Severe personal injury or death may occur if the motorcycle tips or falls. WARNING Inspect Steering and Front Axle 1. Elevate the front of the motorcycle until the front ...

101 MAINTENANCE Fuel System Fuel Hose, Rail, and Connections Inspect the fuel hoses for cracks or damage. Inspect the hose connection at the fuel pump and at the fuel rail for dampness or stains from leaking or dried fuel. Crankcase Ventilation Hose and Connections Remove the operators seat and fuel...

102 MAINTENANCE Fuel System 4. With the engine and exhaust cool, wrap a clean shop towel around the fuel line fitting (2) at the fuel rail. Disconnect it from the fuel rail by squeezing both release buttons (3) simultaneously. Gently slide the fitting from the fuel rail. Notice Fuel can damage paint...

2-4 mm 103 MAINTENANCE Throttle Throttle Control Grip and Cable 1. Rotate the throttle control grip. It should rotate smoothly from its rest position to its completely open position and back again. It should return to its rest position quickly when released. 2. Throttle freeplay is the amount of thr...

104 MAINTENANCE Throttle Adjust Throttle Freeplay 1. Hold the adjuster nuts (1) and loosen the lock nuts (2) on both cables. 2. Turn the lock nuts away from the adjuster nuts as far as possible on both cables. 3. Turn both adjuster nuts toward the lock nuts as far as possible for maximum freeplay in...

105 MAINTENANCE Mechanical Clutch Clutch Lever and Cable 1. Squeeze the clutch lever toward the handlebar and release it. It should move freely and smoothly and should return to its rest position quickly when released. 2. Clutch lever freeplay is the amount of clutch lever movement from the rest pos...

106 MAINTENANCE Mechanical Clutch Adjust Clutch Cable Freeplay 1. Remove the right side cover.2. Hold cable (1) and loosen the adjuster lock nut (2).3. Turn cable adjuster (3) while holding cable.4. Turn the cable adjuster in or out until the clutch lever freeplay (4) is 0.5-1.5 mm. 5. Tighten the a...

107 MAINTENANCE Hydraulic Clutch Hydraulic Clutch Fluid Check the hydraulic clutch fluid level.1. Position the motorcycle in an upright position on level ground. Turn the handlebars until the clutch fluid reservoir is level. 2. View the fluid level through the sight glass. The fluid should be clear ...

108 MAINTENANCE Hydraulic Clutch Add Hydraulic Clutch Fluid 1. Straddle the motorcycle and bring it to a vertical position. Turn the handlebars until the reservoir is horizontal.2. Wipe the area around the reservoir cover with a clean cloth.3. Wipe the clutch fluid container with a clean cloth.4. Re...

109 MAINTENANCE Lubricate Clutch Lever Mechanical Clutch 1. Remove right side cover. Loosen the adjuster lock nut (see page 106.)2. Turn the cable adjuster all the way in to provide maximum lever freeplay.3. Remove clutch lever pivot nut (1) and pivot screw (2). Disconnect the clutch cable from the ...

110 MAINTENANCE Lubricate Control Cables The following cables used on the motorcycle require periodic maintenance and inspection to ensure smooth operation and maximum service life: S Throttle Cables S Mechanical Clutch Cable NOTE: The control cable casings are lined with a low friction sleeve and a...

111 MAINTENANCE Brakes Front Brake Lever Movement Squeeze the front brake lever toward the handlebar and release it. It should move freely and smoothly and should return to its rest position quickly when released. You should feel a firm resistance in the lever within the first 3/4-inch (19 mm) of le...

112 MAINTENANCE Brakes Front Brake Fluid Level 1. Position the motorcycle on level ground with the front wheel straight forward. Do not use the side stand. Position the handlebars so that the brake fluid reservoir is level. 2. View the brake fluid through the sight glass. The fluid should be clear a...

113 MAINTENANCE Brakes Add Front Brake Fluid • Do not operate the front brake while its reservoir cover is removed. Fluid could overflow from the reservoir and cause air to enter the fluid system. Air in the brake fluid system could cause the brakes to malfunction. • Use only DOT 4 brake fluid from ...

114 MAINTENANCE Brakes Adjust Rear Brake Pedal The brake pedal should be adjusted so that in the relaxed position, with no force on the pedal, there is 2-5 mm of freeplay (gap) between the brake pedal stop (A) and the foot peg mount (B).1. Hold the clevis (1) to prevent it from bending, and loosen t...

115 MAINTENANCE Brakes Rear Brake Fluid Level 1. To check the rear brake fluid level, remove right side cover. Straddle the motorcycle and bring it to a vertical position. 2. View the brake fluid through the reservoir. The fluid should be clear and at a level between minimum (MIN) and maximum (MAX) ...

116 MAINTENANCE Brakes Add Rear Brake Fluid 1. Bring the motorcycle to a vertical position with an appropriate motorcycle lift or a block of wood or steel placed securely under the frame. 2. Remove the right side cover.3. Wipe the area around the reservoir cover with a clean cloth.4. Wipe the brake ...

117 MAINTENANCE Brakes Brake Pads Inspect front (1) and rear (2) brake pad thickness. Replace brake pads when wear lines (3) are no longer visible, or when pad thickness reaches 1.5 mm.The shielded pad must be installed on the non-piston side of the caliper. If the brake pads require replacement, se...

118 MAINTENANCE Gear Shift Pedal Adjust Gear Shift Pedal Height 1. Loosen the gear shift linkage rod lock nuts.2. Turn the linkage rod in or out as necessary.3. Tighten the linkage rod lock nuts.4. Check the gear shift pedal height. Notice Do not remove and reposition the shift arm on the shift shaf...

119 MAINTENANCE Tires Tire Pressure Normal riding warms the tires and increases the tire air pressure. For an accurate reading, check the tire pressure before you ride. Adjust tire pressure as required for the total weight of your intended load. Tire Pressure Table* VEGAS JACKPOT Up to 200 lbs (91 k...

120 MAINTENANCE Tires Tire Condition Inspect the tire sidewalls, road contact surface, and tread base for cuts, punctures, and cracking. Replace damaged tires immediately (see your VICTORY Service Manual or an authorized VICTORY dealer). Tread Depth Raised areas at the base of the tread, known as we...

121 MAINTENANCE Wheels Inspect both wheels for cracks or damage. If you see wheel damage or cracks, contact an authorized VICTORY dealer to have the wheel(s) replaced. Do not operate the motorcycle if wheels are damaged or cracked. WARNING

122 MAINTENANCE Spark Plugs The spark plugs must be removed from the engine to inspect them. Spark plugs with bright white deposits, sooty black deposits, or with damaged insulators or electrodes can indicate engine problems. If these conditions exist, or if the condition of one plug is markedly dif...

123 MAINTENANCE Spark Plugs 4. Remove the spark plug from the cylinder head with a 5/8 inch spark plug socket. Both spark plugs should have the same light or medium tan color deposits on the insulator around the electrode tip. The spark plug electrode tip and bridge should have sharp, square edges.I...

124 MAINTENANCE Engine Compression An accurate periodic engine compression check documents engine wear and condition. For engine compression check procedures and special tools required, see the VICTORY Service Manual or contact an authorized VICTORY dealer. Exhaust System Check the exhaust system fo...

125 MAINTENANCE Seat Removal 1. Remove the right and left side covers. See page 46.2. If necessary, remove the fuse box from the bracket. See page 25. 3. Remove the three screws securing the seat to the frame. 4. Lift the rear of the seat and pull rearward and upward to remove it. NOTE: See page 126...

126 MAINTENANCE Seat Installation 1. To reinstall the seat, slide the tongue of the seat into the rubber mount at rear of fuel tank. Push down on the rear of the seat until the screw holes align. 2. Ensure the front seat mount is engaged in the front rubber mount, then install the screws and tighten...

127 MAINTENANCE Battery The battery contains sulfuric acid, which can cause severe burns. Do not allow sulfuric acid to contact skin, eyes, or clothing.Antidotes: • External: Flush with water. • Internal: Drink large quantities of water or milk. Follow with milk of magnesia, beaten eggs, or vegetabl...

128 MAINTENANCE Battery Battery Removal 1. Remove the seat (page 125) and left side cover.2. Remove the two battery retaining bracket nuts and remove the bracket.3. Disconnect the negative (--) battery cables (black cables with ends exposed) first.4. Disconnect the positive (+) cables (cable ends ar...

129 MAINTENANCE Battery Battery Charging The battery may contain explosive gases. • Keep sparks, cigarettes, or any flame away from the battery. • Shield eyes and protect skin and clothing when handling or working near the battery. • Make sure ventilation is adequate when charging or using the batte...

130 MAINTENANCE Battery Battery Installation 1. Before installing the battery, make sure it’s fully charged and clean.2. Tip the battery into position in the battery tray with positive (+) terminal to rear of motorcycle as shown.3. Connect the positive (+) battery cables, tighten securely and instal...

131 MAINTENANCE Fuses Notice Use only recommended amperage fuses to avoid damage to the electrical system. 1. Remove the right side cover. Release the fuse box from the bracket by lifting the tab (1) and sliding the fuse box rearward (see diagram below right.) 2. Release the tabs on each side of the...

132 MAINTENANCE Headlight Beam Inspection The high beam should shine straight forward. The low beam will spread more toward the right (U.S./Canada).1. Before checking the headlight beam, verify that tire pressure (page 119) and rear suspension ride height (page 95) are at specification. 2. Position ...

133 MAINTENANCE Headlight Beam Adjustment 1. To adjust the headlight beam vertically, hold the headlight firmly while loosening the adjustment bolt (1). Adjust the headlight and hold it firmly in position while tightening the bolt. Torque: 35 ft-lbs (47.5 Nm) 2. To adjust the beam horizontally, loos...

134 MAINTENANCE Sidestand Straddle the motorcycle and bring it to a vertical position. Move the sidestand to its stored (up) position, then to its fully extended (down) position, and back again. It should move smoothly and quietly. When the sidestand is in its stored position, the sidestand return s...

135 MAINTENANCE Sidestand Sidestand Lubrication 1. Bring the motorcycle to a vertical position with an appropriate motorcycle lift or a block of wood or steel placed securely under the frame. 2. Move the sidestand to its stored (up) position. Wear face protection. The sidestand return spring is unde...

136 MAINTENANCE Fasteners Visually inspect the entire motorcycle chassis and engine for loose, damaged, or missing fasteners. Tighten loose fasteners to the proper torque (see the Specifications section of the Owner’s Manual , or the VICTORY Service Manual ). Replace stripped, damaged, or broken fas...

137 CLEANING This section explains how to properly clean the various parts of your VICTORY motorcycle to keep it in good working order and appearance. General Cleaning Clean your motorcycle regularly to protect it from corrosion and to keep it looking new. As you clean your motorcycle you perform a ...

138 CLEANING Washing and Drying the Motorcycle Before washing the motorcycle, always allow the engine to cool for at least 30 minutes. Do not spray water on a hot engine. Make sure the exhaust pipes have cooled. Cover each exhaust pipe opening with a plastic bag and attach the bag to the pipe with a...

139 CLEANING Washing and Drying the Motorcycle 4. Wash the entire motorcycle using a soft cloth or sponge soaked in a solution of mild detergent and warm water. Use plenty of the water/detergent solution while washing, and apply minimal pressure. Excessive pressure may cause debris to scratch the fi...

140 CLEANING Waxing, Polishing and Applying Protectants (Items Other Than Windshields and Leather Saddlebags) After washing and drying the motorcycle, you can help extend the life and appearance of its components by waxing painted surfaces, polishing chrome surfaces, and applying a protectant to exp...

141 CLEANING Windshield Care If your motorcycle is equipped with an optional windshield:Wash the windshield using a soft cloth or sponge soaked in a solution of mild detergent and warm water, applying minimal pressure as you wash. Let the detergent do the cleaning, not the pressure you apply. Excess...

142 CLEANING Leather Saddlebag Care If your motorcycle is equipped with optional leather saddlebags:Natural leather has “character.” Each piece used in the construction of these saddlebags is unique, and will settle into its own distinct form over time and miles. Mature leather is one-of-a-kind, and...

143 STORAGE If you will not operate the motorcycle for several months, such as during the winter, store the motorcycle to prevent damage to the fuel system and the battery and to protect components from corrosion or deterioration. During storage you might use products that are potentially hazardous;...

144 STORAGE Fuel Stabilizer 1. Using a mixture of fuel and the recommended amount of VICTORY Premium Carbon Clean Plus or other gasoline stabilizer, fill the fuel tank only to the top of the filler insert. 2. Ride the motorcycle or start and run the engine for 15 minutes in a well ventilated area to...

145 STORAGE Tire Inflation Inflate the tires to normal pressure (see page 119). Battery Care 1. Remove the battery (see page 128).2. To clean oxidation from the battery posts and cable connectors, use a wire brush. Wash the posts and cable connectors with a solution of 1 part baking soda to 16 parts...

146 STORAGE Removal from Storage 1. Remove the cover and unlock the front forks (if locked with accessory lock).2. Check the tire pressure (page 119) and inflate the tires if necessary.3. Reinstall the battery (see page 130).4. Wash and dry the entire motorcycle (see page 138).5. Prior to starting t...

147 WARRANTIES Motorcycle Noise Regulation Tampering with noise control systems is prohibited. Federal law prohibits the following acts or causing thereof: S The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement, of any device or element of...

148 WARRANTIES Emissions Control System Warranty VICTORY Motorcycles, Polaris Sales Inc. - Emission Control System Warranty Statement Your Warranty Rights and Obligations The California Air Resources Board and VICTORY Motorcycle Division, Polaris Sales Inc. (hereinafter VICTORY) are pleased to expla...

149 WARRANTIES Owner’s Warranty Responsibilities As the motorcycle owner, you are responsible for the performance of the required maintenance listed in your owner’s manual. VICTORY recommends that you retain all receipts covering maintenance on your motorcycle, but VICTORY cannot deny warranty solel...

152 WARRANTIES III. Limited Liability A. The liability of VICTORY under this Emission Control System Warranty is limited solely to the remedying of defects in material orworkmanship by an authorized VICTORY motorcycle dealer at its place of business during customary business hours. This warranty doe...

153 WARRANTIES IV. Legal Rights THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARYFROM STATE TO STATE. V. This Warranty Is In Addition To The VICTORY Limited Motorcycle Warranty. VI. Additional Information. Any replacement part that is equivalent in performa...

154 WARRANTIES VICTORY Motorcycle Warranty Policy Limited Warranty VICTORY Motorcycle Division, Polaris Sales Inc., P.O. Box 47700, Medina, Minnesota 55340-9960, gives a ONE YEAR LIMITED WARRANTY on all components of the VICTORY Motorcycle against defects in material or workmanship. This warranty co...

155 WARRANTIES Warranty Coverage And Exclusions: Limitations Of Warranties And Remedies The warranty excludes any failures that are not caused by a defect in material or workmanship. This warranty does not cover accidental damage, normal wear and tear, abuse or improper handling. This warranty also ...

157 SPECIFICATIONS Model Year 2009 VEGAS JACKPOT / NESS JACKPOT Dimensions Overall Length 96.3 in (244.6 cm) Overall Width 37.0 in. (94 cm) Overall Height 47.25 in (120.0 cm) Seat Height 25.70 in (65.3 cm) Wheelbase 66.3 in (168.4 cm) Ground Clearance 5.3 in (13.5 cm) Rake/Trail 33.5 ° / 5.12 in. (1...

161 SPECIFICATIONS Fuel Specifications Use only unleaded gasoline, 92 pump octane minimum.DO NOT USE E85 GASOLINE OR GASOLINE CONTAINING METHANOL.Using E85 gasoline or gasoline/methanol blends can result in poor starting and driveability, and may damage critical fuel system components.Gasoline conta...

162 IDENTIFICATION NUMBERS Record important numbers below. Vehicle Identification Number: ________________________________________ (Located on right side of steering head, see page 33) Engine Identification Number: ________________________________________ (Located on right crankcase to right of brea...

163 INDEX A Accelerating 70 . . . . . . . . . . . . . . . . . . . . Accessory Battery Charger 129 . . . . . . . . Accessory Selection and Installation 18 . . Adjustment Clutch Lever Freeplay 106 . . . . . . . Drive Belt Tension 90 . . . . . . . . . Gear Shift Pedal Height 118 . . . . . Headlight Bea...