Polaris 2008 Ranger Crew- Manuals

5 SAFETY Safety Decals and Locations Warning decals have been placed on the vehicle for your protection. Read and follow the instructions of the decals on the vehicle carefully. If any of the decals depicted in this manual differ from the decals on your vehicle, always read and follow the instructio...

6 SAFETY Safety Decals and Locations Clutch Cover Warning WARNINGNO STEP• Moving parts hazard under belt-clutch guard. To prevent serious injury, do not operate vehicle with guard removed. • Do not modify engine or clutch. Doing so can cause part failure, possible imbal- ance, and excessive engine R...

7 SAFETY Safety Decals and Locations Age Warning WARNINGOperating this vehicle if you are under the age of 16 increases your chance of severe injury or death. NEVER operate this vehicle if you are under age 16 or without a valid driver’s license. 7175101 Shift Caution CAUTIONTo avoid transmission da...

8 SAFETY Operator Safety Age Restrictions This vehicle is an ADULT VEHICLE ONLY. Operation is prohibited for anyone under 16 years of age or anyone without a valid driver’s license. No person under the age of 5 may ride as a passenger in this vehicle. Know Your Vehicle As the operator of the vehicle...

9 SAFETY Operator Safety The following signal words and symbols appear throughout this manual and on your vehicle. Your safety is involved when these words and sym- bols are used. Become familiar with their meanings before reading the manual. The safety alert symbol , on your vehicle or in this manu...

13 SAFETY Operator Safety Equipment Modifications We are concerned for the safety of our customers and for the general public. Therefore, we strongly recommend that consumers do not install on a Polaris RANGER any equipment that may increase the speed or power of the vehicle, or make any other modif...

21 SAFETY Fuel Safety WARNING Gasoline is highly flammable and is explosive under certain conditions. Always exercise extreme caution whenever handling gasoline.Always stop the engine when refueling.Always refuel outdoors or in a well ventilated area.Do not smoke or allow open flames or sparks in or...

22 FEATURES AND CONTROLS Component Locations Some Polaris vehicles are equipped with special features such as the cab frame. Not all models come with all features. Refer to the specifications section beginning on page 108. Cab Frame Console Steering Wheel Hip Bar Fuel Tank Cap Seat Belts Cargo Box B...

23 FEATURES AND CONTROLS Component Locations Headlights Hood Hold-Down Strap Front Bumper/Brush Guard Radiator

24 FEATURES AND CONTROLS Component Locations Trailer Hitch Bracket This vehicle is equipped with a receiver hitch bracket for a trailer hitch. Trailer towing equipment is not supplied with this vehicle.To avoid injury and property damage, always heed the warnings and towing capacities outlined on pa...

25 FEATURES AND CONTROLS Component Locations Instrument Cluster Your RANGER is equipped with an instrument cluster that senses vehi- cle speed from the right front wheel. The instrument cluster measures distance in miles as well as time, hours of operation and engine RPM. Refer to page 34 for the lo...

26 FEATURES AND CONTROLS Instrument Cluster Rider Information Center The rider information center is located in the instrument cluster. All seg- ments will light up for 2.5 seconds at start-up. NOTE: If the instrument cluster fails to illuminate, a battery over-voltage may have occurred and the inst...

27 FEATURES AND CONTROLS Instrument Cluster Rider Information Center Standard Modes Use the yellow mode button located under the speedometer to toggle through the mode options. See page 34. Odometer Mode The odometer records the miles traveled by the vehicle. Trip Meter Mode The trip meter records t...

28 FEATURES AND CONTROLS Instrument Cluster Rider Information Center Diagnostic Mode The wrench icon will display when the gauge is in the diagnostic mode. To exit the diagnostic mode, turn the key switch off and on. Any move- ment of the tires will also cause the gauge to exit the diagnostic mode.T...

30 FEATURES AND CONTROLS Instrument Cluster Rider Information Center Diagnostic Mode Programmable service interval To enable or disable the service interval: 1. Enter the diagnostic mode. 2. Toggle to the service interval screen. 3. Press and hold the mode button for about seven (7) seconds, until e...

31 FEATURES AND CONTROLS Instrument Cluster Rider Information Center Downloading Codes The EFI diagnostic mode is for informational purposes only. Please see your Polaris dealer for all major repairs. See page 32 for Blink Codes and Failure Descriptions. Use the follow- ing procedure to download bli...

32 FEATURES AND CONTROLS Instrument Cluster Rider Information Center Downloading Codes Blink Code Failure Description -- No RPM Signal 21 Loss of Synchronization 45 Barometric Pressure Sensor: Circuit Low Input 46 Barometric Pressure Sensor: Circuit High Input 22 TPS: Open or Short Circuit to Ground...

33 FEATURES AND CONTROLS Seat Removal Pull up on the front of the seat and slide it toward the front of the vehi- cle.Install the seat by sliding the tabs into the rear of the seat base. Push down firmly on the front of the seat until the pins are fully seated into the grommets. Fuel Cap The fuel ta...

34 FEATURES AND CONTROLS Console Auxiliary Outlets Each 12-volt accessory plug receptacle has spade connections on the back that may be used to power an auxiliary light or other optional accessories or lights. One outlet is located on the console. The connec- tions are behind the console, under the ...

35 FEATURES AND CONTROLS Gear Selector H: High GearL: Low GearN: NeutralR: Reverse NOTE: Low gear is the primary driving range for the RANGER . High gear is intended for use on hard- packed surfaces with light loads. To change gears, stop the vehicle, and with the engine idling, move the lever to th...

36 FEATURES AND CONTROLS Brake Pedal Depress the brake pedal to slow or stop the vehicle. Apply the brakes while starting the engine. Throttle Pedal Push the pedal down to increase engine speed. Spring pressure returns the pedal to the rest position when released. Always check that the throttle peda...

37 FEATURES AND CONTROLS Park Brake Lever To help prevent the vehicle from rolling, engage the park brake when parking the vehicle. When the park brake is fully engaged and the park brake indicator is illuminated, engine speed is limited to 1300 RPM in all gears, including neutral. If throttle is ap...

38 FEATURES AND CONTROLS Switches Ignition Switch The ignition switch is a three-position, key-operated switch. The key can be removed from the switch when it is in the OFF position. OFF The engine is off. Electrical circuits are off, except Acc, 12V. ON Electrical circuits are on. Electrical equipm...

39 FEATURES AND CONTROLS Switches Light Switch The ignition switch key must be in the ON/ RUN position to operate the headlights. Use the light switch to turn the headlights on or off. AWD/Differential Lock Switch The AWD/Differential Switch has three posi- tions: • All Wheel Drive (AWD)• Differenti...

40 OPERATION Break-In Period The break-in period for your new Polaris RANGER is the first twenty hours of operation, or the time it takes to use the first two tanks full of gasoline. No single action on your part is as important as a proper break- in period. Careful treatment of a new engine will re...

41 OPERATION Pre-Ride Inspection WARNING If a proper inspection is not done before each use, severe injury or death could result. Always inspect the vehicle before each use to ensure it's in proper operating condition. Item Remarks Page Brake system/pedal travel Ensure proper operation 36 87 Brake f...

42 OPERATION Starting the Engine 1. Sit in the driver's seat and fasten the seat belt.2. Apply the brakes. Engage the park brake.3. Shift the transmission to neutral. NOTE: Do not press the throttle pedal while starting the engine. 4. Turn the ignition key past the ON/RUN position to START. Engage t...

43 OPERATION Stopping the Engine 1. Release the throttle pedal completely and brake to a complete stop.2. Turn the engine off.3. Engage the park brake. Braking 1. Release the throttle pedal completely.2. Press on the brake pedal evenly and firmly. NOTE: Practice starting and stopping (using the brak...

44 OPERATION Driving Safely Driving Procedure 1. Sit in the driver's seat and fasten the seat belt.2. After starting the engine and allowing it to warm up, apply the ser- vice brakes, and shift the transmission into gear. 3. Check your surroundings and determine your path of travel.4. Release the pa...

45 OPERATION Driving Safely Driving on Slippery Surfaces When driving on slippery surfaces such as wet trails, loose gravel, or ice, be alert for the possibility of skidding and sliding. Under these con- ditions, follow these precautions:1. Slow down when entering slippery areas.2. Maintain a high l...

46 OPERATION Driving Safely Driving Uphill Whenever traveling uphill, follow these precautions:1. Always travel straight uphill. 2. Avoid steep hills (15 ° maximum). 3. Keep both feet on the floor. 4. Proceed at a steady rate of speed and throttle opening. WARNING Climbing hills improperly can cause...

47 OPERATION Driving Safely Driving on a Sidehill (Sidehilling) Driving Downhill Whenever descending a hill, follow these precautions:1. Proceed directly downhill.2. Slow down.3. Apply the brakes slightly to aid in slowing. WARNING Crossing hillsides or turning on hills can result in loss of control...

48 OPERATION Driving Safely Driving Through Water Your Polaris RANGER can operate through water up to a maximum recommended depth equal to the floor- boards. Follow these procedures when oper- ating through water:1. Always determine water depths and current before entering. 2. Choose a crossing wher...

49 OPERATION Driving Safely Driving Over Obstacles Be alert! Look ahead and learn to read the terrain you're traveling on. Watch for hazards such as logs, rocks and low hanging branches. WARNING Severe injury or death can result if your vehicle suddenly comes in contact with a hidden obstacle. Not a...

50 OPERATION Driving Safely Driving in Reverse Follow these guidelines when operating in reverse:1. Back slowly.2. Apply the brakes lightly for stopping.3. Avoid turning at sharp angles.4. Never open the throttle suddenly while backing.5. Always inspect left and right fields of vision before backing...

51 OPERATION Driving Safely Parking on an Incline Avoid parking on an incline if possible. If it's unavoidable, follow these precautions:1. Place the transmission in gear.2. Apply the brakes. Engage the park brake.3. Turn the engine off.4. Block the rear wheels on the downhill side. WARNING A rollin...

52 OPERATION Driving Safely Hauling Cargo WARNING Hauling cargo improperly can alter vehicle handling and may cause loss of control or brake instability, which can result in serious injury or death. Always follow these precautions when hauling cargo:REDUCE SPEED AND ALLOW GREATER DISTANCES FOR BRAKI...

53 OPERATION Driving Safely Hauling Cargo This vehicle has been designed to carry or tow specific capacities. Always read and understand the load distribution warnings listed on the warning labels. Never exceed the stated capacities. Model Maximum Total Weight Capacity (Level Ground) Maximum Cargo B...

54 OPERATION Driving Safely Dumping the Cargo Box 1. Select a level site to dump the cargo box. Do not attempt to dump or unload the vehicle while parked on an incline. 2. Apply the brakes. Engage the park brake. 3. Dismount the vehicle.4. Ensure that the cargo is positioned evenly or toward the fro...

55 OPERATION Driving Safely Towing Loads Belt Life To extend belt life, use the lowest gear possible when hauling or towing heavy cargo. WARNING Towing improperly can alter vehicle handling and may cause loss of control or brake instability, which can result in serious injury or death. Always follow...

56 OPERATION Driving Safely Parking the Vehicle 1. Apply the brakes. Stop the vehicle on a level surface.2. Turn the engine off.3. Engage the park brake.4. Remove the ignition switch key to prevent unauthorized use. WARNING A rolling vehicle can cause property damage and serious injury. Always engag...

57 OPERATION Differential Lock Locking the Differential The rear axle is equipped with a lock- able differential that allows the oper- ator to choose between an open differential or a closed differential. Locking the differential in slippery or low traction conditions helps improve traction.Press th...

58 OPERATION All Wheel Drive (AWD) The illuminated amber AWD switch indicates that the vehicle is in AWD.When the AWD switch is on, the front wheels will automatically engage any time the rear wheels lose traction. When the rear wheels regain traction, the front wheels will automatically disengage. ...

59 EMISSION CONTROL SYSTEMS Noise Emission Control System Do not modify the engine, intake or exhaust components, as doing so may affect compliance with U.S.A. EPA noise control requirements (40 CFR 205) and local noise level requirements. Operation on Public Lands in the U.S.A. Your Polaris vehicle...

60 MAINTENANCE Periodic Maintenance Chart Careful periodic maintenance will help keep your vehicle in the safest, most reliable condition. Inspection, adjustment and lubrication of important components are explained in the periodic maintenance chart.Inspect, clean, lubricate, adjust and replace part...

61 MAINTENANCE Periodic Maintenance Chart Maintenance Chart Key X Perform these operations more often for vehicles subjected to severe use. E Emission Control System Service - 4 Cycle (California) Q Have an authorized Polaris dealer perform these services. WARNING Improperly performing the procedure...

65 MAINTENANCE Lubrication Recommendations Check and lubricate all components at the intervals outlined in the Peri- odic Maintenance Chart beginning on page 60, or more often under severe use, such as wet or dusty conditions. Items not listed in the chart should be lubricated at the general lubrica...

66 MAINTENANCE Lubrication Recommendations Prop Shaft U-Joint Ball Joint (if equipped)

67 MAINTENANCE Engine Oil Always check and change the engine oil at the intervals outlined in the Periodic Maintenance Chart beginning on page 60. Always change the oil filter whenever changing oil. Oil Recommendations Polaris recommends the use of Polaris PS-4 PLUS Performance Syn- thetic 2W-50 4-c...

68 MAINTENANCE Engine Oil Always check and change the oil at the intervals outlined in the Periodic Maintenance Chart beginning on page 60. Always use the recommended engine oil. Oil Check The oil dipstick and fill tube is located on the engine.1. Position the vehicle on a level surface. 2. Apply th...

69 MAINTENANCE Engine Oil Oil and Filter Change Always change the oil and filter at the intervals outlined in the Periodic Maintenance Chart beginning on page 60. Always change the oil filter whenever changing oil.1. Position the vehicle on a level surface.2. Run the engine for two to three minutes ...

70 MAINTENANCE Engine Oil Oil and Filter Change 12. Remove the dipstick and fill the sump with two quarts (1.9 l) of rec- ommended oil. 13. Shift the transmission to neutral. 14. Apply the brakes. Engage the park brake.15. Start the engine. Allow it to idle for one to two minutes. 16. Stop the engin...

71 MAINTENANCE Gearcases Transmission (Main Gearcase) Always check and change the transmission oil at the intervals outlined in the Periodic Maintenance Chart beginning on page 60. Maintain the oil level even with the bottom of the fill plug hole.Refer to the Gearcase Specifications Chart on page 70...

72 MAINTENANCE Gearcases Transmission (Main Gearcase) Oil Change The drain plug is located on the bottom of the transmission. Access the drain plug through the drain hole in the skid plate.1. Remove the fill plug.2. Place a drain pan under the drain plug. Remove the drain plug. Drain the oil. Dispos...

73 MAINTENANCE Gearcases Front Gearcase Always check and change the front gearcase oil at the intervals outlined in the Periodic Maintenance Chart beginning on page 60. Maintain the oil level even with the bottom thread of the fill plug hole. Refer to the Gearcase Specifications Chart on page 70 for...

74 MAINTENANCE Gearcases Rear Gearcase Always check and change the rear gearcase oil at the intervals outlined in the Periodic Maintenance Chart beginning on page 60.Refer to the Gearcase Specifications Chart on page 70 for recommended lubricants, capacities and torque specifications. See page 110 f...

75 MAINTENANCE Spark Plugs Spark Plug Gap/ Torque Spark plug condition is indicative of engine operation. The spark plug firing end condition should be read after the engine is warmed up and the vehicle is driven at higher speeds. Immediately check the spark plug for correct color. See page 76. CAUT...

76 MAINTENANCE Spark Plugs Spark Plug Condition Normal Plug The normal insulator tip is gray, tan or light brown. There will be few combustion deposits. The electrodes are not burned or eroded. This indi- cates the proper type and heat range for the engine and the service. NOTE: The tip should not b...

77 MAINTENANCE Cooling System Operation The engine coolant level is controlled or maintained by the recovery system. The recovery system components are the overflow bottle, radia- tor filler neck, radiator pressure cap and connecting hose.As coolant operating temperature increases, the expanding (he...

78 MAINTENANCE Cooling System Radiator and Cooling Fan Always check and clean the screen and radiator fins at the intervals out- lined in the Periodic Maintenance Chart beginning on page 60. Do not obstruct or deflect air flow through the radiator by installing unautho- rized accessories in front of...

79 MAINTENANCE Cooling System Radiator Coolant Level Always check and clean the screen and radiator fins at the intervals out- lined in the Periodic Maintenance Chart beginning on page 60. Do not obstruct or deflect air flow through the radiator by installing unautho- rized accessories in front of t...

80 MAINTENANCE Polaris Variable Transmission (PVT) System Belt slip is responsible for creating excessive heat that destroys belts, wears clutch components and causes outer clutch covers to fail. Switch to low range while operating at slower speeds to extend the life of the PVT components (belt, cov...

81 MAINTENANCE PVT System WARNING Failure to comply with the instructions in this warning can result in severe injury or death.Do not modify any component of the PVT system. Doing so may reduce its strength so that a failure may occur at a high speed. The PVT system has been precision balanced. Any ...

82 MAINTENANCE PVT System PVT Drying There may be some instances when water is accidently ingested into the PVT system. Use the following instructions to dry it out before operat- ing.1. Loosen the bottom screws that secure the clutch cover.2. Allow the water to drain.3. Tighten the screws.4. Apply ...

83 MAINTENANCE Filter Systems Air Filter Always change the air filter at the intervals outlined in the Periodic Maintenance Chart beginning on page 60. 1. Lift the cargo box to access the air box. 2. Remove the air box cover and inspect the gasket. It should adhere tightly to the cover and seal all ...

84 MAINTENANCE Spark Arrestor Use the following procedure to periodically purge accumulated carbon from the exhaust pipe.1. Remove the arrestor clean-out plugs located on the bottom of the muffler. 2. Shift the transmission to neutral. Apply the brakes. Start the engine. 3. Purge accumulated carbon ...

85 MAINTENANCE Throttle System Throttle Freeplay If the throttle pedal has excessive play due to cable stretch or mis- adjustment, it will cause a delay in throttle response, especially at low engine speed. The throttle may also not open fully. If the throttle pedal has no freeplay, the throttle may...

86 MAINTENANCE Throttle System Throttle Body/Idle RPM Idle RPM is preset by the manufacturer. If the engine idle speed is not satisfactory, please see your Polaris dealer for adjustment. Throttle Freeplay Adjustment 1. Remove the seat.2. Locate the throttle cable adjuster. 3. Squeeze the end of the ...

87 MAINTENANCE Brakes The front and rear brakes are hydraulic disc type brakes activated by the brake pedal. See page 36. Brake Fluid Inspect the brake system rou- tinely. Inspect the level of the brake fluid before each opera- tion.Change the brake fluid every two years and any time the fluid becom...

88 MAINTENANCE Brakes Brake Inspection 1. Check the brake system for fluid leaks. 2. Check the brake pedal for excessive travel or a spongy feel. 3. Check the friction pads for wear, damage and looseness. 4. Inspect the brake disc spline and pad wear surface for excessive wear. 5. Change pads when w...

89 MAINTENANCE Steering Wheel Inspection Check the steering wheel for specified freeplay and smooth operation at the intervals outlined in the Periodic Maintenance Chart beginning on page 60. 1. Position the vehicle on level ground.2. Lightly turn the steering wheel left and right.3. There should be...

90 MAINTENANCE Seat Belts Inspect all three seat belts for proper operation before each use of the vehicle.1. Push the latch plate into the buckle until it clicks. The latch plate must slide smoothly into the buckle. A click indicates that it's securely latched. 2. Push the red button in the middle ...

91 MAINTENANCE Tires Tire Tread Depth Always replace tires when tread depth is worn to 1/8" (3 mm) or less. Axle and Wheel Nut Torque Specifications Inspect the following items occasionally for tightness, and if they've been loosened for maintenance service. NOTE: Do not lubricate the stud or th...

92 MAINTENANCE Tires Wheel Removal 1. Apply the brakes. Stop the engine. Place the transmission in gear. Engage the park brake. 2. Loosen the wheel nuts slightly.3. Elevate the side of the vehicle by placing a suitable stand under the frame. 4. Remove the wheel nuts and washers. Remove the wheel. Wh...

93 MAINTENANCE Lights When servicing a halogen lamp, don't touch the lamp with bare fingers. Oil from your skin leaves a residue, causing a hot spot that will shorten the life of the lamp. Headlight Lamp Replacement 1. Open the hood.2. Unplug the headlamp from the wiring harness. Be sure to pull on ...

94 MAINTENANCE Lights Headlight Beam Adjustment 1. Place the vehicle on a level surface with the headlight approxi- mately 25 ft. (7.6 m) from a wall. 2. Measure the distance from the floor to the center of the headlight and make a mark on the wall at the same height. 3. Apply the brakes. Start the ...

95 MAINTENANCE Vehicle Immersion If it's impossible to take your RANGER to a dealer before starting it, fol- low the steps outlined below.1. Move the vehicle to dry land or at the very least, to water below the footrests. 2. Dry any water present in the air box.3. Filter replacement is required if w...

96 MAINTENANCE Battery Your vehicle may have either a sealed battery, which requires little maintenance, or a conventional battery. A sealed battery can be identi- fied by its flat covers on the top of the battery. A conventional battery has six filler caps on the top of the battery. Conventional Ba...

97 MAINTENANCE Battery Battery Removal 1. Open the hood.2. On conventional batteries, remove the battery vent tube. 3. Disconnect the black (nega- tive) battery cable first. 4. Disconnect the red (positive) battery cable last. 5. Lift the battery out of the vehicle. Be careful not to tip a conventio...

98 MAINTENANCE Battery Battery Installation Using a new battery that has not been fully charged can damage the bat- tery and result in a shorter life. It can also hinder vehicle performance. Follow the battery charging instructions on page 100 before installing the battery.1. Ensure that the battery...

99 MAINTENANCE Battery Battery Storage Whenever the vehicle is not used for a period of three months or more, remove the battery from the vehicle, ensure that it's fully charged, and store it out of the sun in a cool, dry place. Check battery voltage each month during storage and recharge as needed ...

100 MAINTENANCE Battery Battery Charging (Conventional Battery) 1. Remove the battery from the vehicle to prevent damage from leak- ing or spilled electrolyte during charging. See page 97. 2. Charge the battery with a charging output no larger than 1/10 of the battery’s amp/hr rating. Charge as need...

101 MAINTENANCE Battery Battery Charging (Sealed Battery) NOTE: Always verify battery condition before and 1-2 hours after the end of charging. Fuses The vehicle wire harness is protected by self-resetting circuit breakers (fuses). Do not attempt to replace these fuses.If the engine stops or will no...

102 MAINTENANCE Cleaning and Storage Washing the Vehicle Keeping your Polaris vehicle clean will not only improve its appearance but it can also extend the life of various components. The best and safest way to clean your Polaris vehicle is with a garden hose and a pail of mild soap and water.1. Use...

103 MAINTENANCE Cleaning and Storage Washing the Vehicle If a high pressure water system is used for cleaning (not recommended), exercise extreme caution. The water may damage components and could remove paint and decals. Avoid directing the water stream at the follow- ing items: • Wheel bearings• R...

104 MAINTENANCE Cleaning and Storage Chrome Wheel Care (if equipped) Proper maintenance will protect chrome wheels from corrosion, pre- serve wheel life and ensure a “like new” appearance for many years. NOTE: Chrome wheels exposed to road salt (or salt in the air in coastal areas) are more suscepti...

105 MAINTENANCE Cleaning and Storage Storage Tips Clean the Exterior Make any necessary repairs and clean the vehicle as recommended. See page 102. Stabilize the Fuel 1. Fill the fuel tank.2. Add Polaris Carbon Clean Fuel Treatment or Polaris Fuel Stabilizer. Follow the instructions on the container...

106 MAINTENANCE Cleaning and Storage Storage Tips Fog the Engine 1. Treat the fuel system with Polaris Carbon Clean. Follow the instruc- tions on the container. Start the engine. Allow it to idle for several minutes so the Carbon Clean reaches the injectors. Stop the engine. 2. Remove the spark plug...

107 MAINTENANCE Removal from Storage 1. Check the battery electrolyte level and charge the battery if neces- sary. Install it in the vehicle. Make sure the battery vent hose is routed properly and that it's not pinched or restricted in any way. 2. Make sure the spark plug is tight.3. Fill the fuel t...

108 SPECIFICATIONS RANGER Crew Maximum Weight Capacity 1750 lbs. (795 kg) (includes weight of operator, passengers, cargo, accessories) Fuel Capacity 8.8 gal. (33.3 l) Engine Oil Capacity 2 qts. (2.1 l) Coolant Capacity 1.6 gal. (6 l) Towing Capacity 2000 lbs. (907 kg) Hitch Tongue Capacity 150 lbs....

110 POLARIS PRODUCTS Part Number Description Engine Lubricant 2870791 Fogging Oil (12 oz. Aerosol) 2876244 PS-4 PLUS Performance Synthetic 2W-50 4-Cycle Oil (qt./.95 l) 2876245 PS-4 PLUS Performance Synthetic 2W-50 4-Cycle Oil (gal./3.8 l) Gearcase / Transmission Lubricants 2873602 Premium AGL Synth...

111 TROUBLESHOOTING Drive Belt Wear/Burn Possible Cause Solution Driving onto a pickup or tall trailer in high range Use low range during loading. Starting out going up a steep incline Use low range. See warnings on page 46. Driving at low RPM or ground speed (3-7 MPH) Drive at a higher speed or use...

112 TROUBLESHOOTING Park Brake Engine Limiting Feature Fails to Disengage Engine Doesn't Turn Over Engine Turns Over, Fails to Start Engine Backfires Possible Cause Solution Park brake is not completely disengaged Ensure lever is in forward-most position Park brake connector malfunction or switch mo...

113 TROUBLESHOOTING Engine Pings or Knocks Engine Runs Irregularly, Stalls or Misfires Possible Cause Solution Poor quality or low octane fuel Replace with recommended fuel Incorrect ignition timing See your dealer Incorrect spark plug gap or heat range Set gap to specs or replace plugs Possible Cau...

114 TROUBLESHOOTING Engine Stops or Loses Power Possible Cause Solution Out of fuel Refuel Kinked or plugged fuel vent line Inspect and replace Water is present in fuel Replace with new fuel Fouled or defective spark plugs Inspect, clean and/or replace spark plug Worn or defective spark plug wires S...

115 WARRANTY LIMITED WARRANTY Polaris Sales Inc., 2100 Highway 55, Medina, MN 55340, gives a SIX MONTH LIM- ITED WARRANTY on all components of the Polaris RANGER against defects in mate- rial or workmanship. Polaris also gives a one year limited warranty on the final drive chain for failure due to d...

116 WARRANTY LIMITATIONS OF WARRANTIES AND REMEDIES ALL IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PAR- TICULAR PURPOSE) ARE LIMITED IN DURATION TO THE ABOVE SIX MONTH WARRANTY PERIOD. POLARIS FURTHER DISCLAIMS ALL EXPRESS WARRANTIES ...

117 WARRANTY Exported Vehicles EXCEPT WHERE SPECIFICALLY REQUIRED BY LAW, THERE IS NO WAR- RANTY OR SERVICE BULLETIN COVERAGE ON THIS VEHICLE IF IT IS SOLD OUTSIDE THE COUNTRY OF THE SELLING DEALER'S AUTHORIZED LOCA- TION.This policy does not apply to vehicles that have received authorization for ex...

119 WARRANTY California Emission Control Warranty Statement Your Warranty Rights and Obligations The California Air Resources Board and Polaris Industries Inc., 2100 Highway 55, Medina, Minnesota 55340 (herein "POLARIS") are pleased to explain the emission con- trol system warranty on your 2...

120 WARRANTY California Emission Control Warranty Statement Owner's Warranty Responsibilities: • As the LSI engine owner, you are responsible for the performance of the required maintenance listed in your Owner's Safety and Maintenance Manual (herein "Owner's Manual"). POLARIS recommends tha...

121 WARRANTY California Emission Control Warranty Statement Emission-Related Parts Covered Under This Warranty (1) Fuel Metering System (i) Carburetor and internal parts (and/or pressure regulator or fuel injection system)(ii) Air/fuel ratio feedback and control system, if applicable(iii) Cold start...

122 WARRANTY California Emission Control Warranty Statement What is Not Covered Under This Warranty This warranty does not cover any emission-related part which malfunctions, fails or is damaged due to alterations and/or modifications such as changing, adding or removing parts.When the LSI engine is...

123 WARRANTY X Perform these procedures more often for vehicles subjected to severe use. E Emission-Related Service. Q Have an authorized Polaris dealer perform these services Repair and Replacement of Emission-Related Parts It is recommended that only LSI engine replacement parts, which have been a...

124 MAINTENANCE LOG Use the following chart to record periodic maintenance. DATE MILES (KM) OR HOURS TECHNICIAN SERVICE PERFORMED / COMMENTS

126 INDEX A Accessory Outlets, 12-Volt . . . . . . . 34 Adjustment Headlight Beam . . . . . . . . . . . . 94 Rear Spring . . . . . . . . . . . . . . . 89 Rear Suspension . . . . . . . . . . . 89 Throttle Freeplay . . . . . . . . . . . 86 Age Restrictions. . . . . . . . . . . . . . . . . 8 Air Filter...

129 INDEX S Specifications . . . . . . . . . . . . . 108-109 Specifications, Gearcase . . . . . . . . . . 70 Speed, Towing . . . . . . . . . . . . . . . . . 55 Speedometer . . . . . . . . . . . . . . . . . . . 25 Spring, Rear, Adjustment . . . . . . . . . 89 Stabilizing the Fuel . . . . . . . . . . ...