Pelco CM9740-UPG-8312 - Manuals

Page 3 - CONTENTS; Section; LIST OF ILLUSTRATIONS; Figure

CONTENTS Section Page INTRODUCTION .................................................................................................................................................................................................................. 1 SOFTWARE UPGRADE OVERVIEW .............................

Page 5 - INTRODUCTION; Chip extraction tool, part number ICPULLERTOOL

C1547M (7/03) 1 INTRODUCTION The CM9740-UPG-8312 software upgrade kit provides the following items to upgrade System 9740 ™ software: 1 System 9740 Setup Disk, version 3.74 1 System 9740 Operation Disk, version 8.03.012 1 System 9740 Utility Disk, version 8.03.012 1 CM9740/9760 Resource CD-ROM, vers...

Page 6 - SOFTWARE UPGRADE OVERVIEW

2 C1547M (7/03) SOFTWARE UPGRADE OVERVIEW Upgrading System 9740 software to version 8.03.012 involves upgrading CM9740-CC1 software and System Managersoftware. For proper operation of a 9740 system, however, additional components—such as CM9740-MXB and CM9760-KBD/CM9760-KBR firmware—must also be upg...

Page 7 - UPGRADING SYSTEM 9740 SOFTWARE IN A SINGLE-NODE SYSTEM; filename; test

C1547M (7/03) 3 UPGRADING SYSTEM 9740 SOFTWARE IN A SINGLE-NODE SYSTEM NOTE: Any external computer interface (such as an access control system, alarm system, fire system, building management/ control system, or VMX200) that is using the P protocol to communicate with a CM9740-CC1 running version 7.8...

Page 8 - del

4 C1547M (7/03) b. Remove the current System Manager program: (1) In the Windows taskbar, click the Start button. (2) Highlight Settings and then click Control Panel . (3) Double-click the Add/Remove Programs icon. (4) For a PC running Windows 95/98/NT: On the Install/Uninstall tab, click the System...

Page 9 - to reboot the 9740 system.

C1547M (7/03) 5 9. Upgrade the CC1 system software executable file, CM9740.EXE: a. Insert the System 9740 Operation Disk, Version 8.03.012, into the disk drive of the CC1. b. Copy the CM9740.EXE executable file from the 9740 directory on the Operation Disk to the C:\9740 directory of theCC1. At the ...

Page 10 - UPGRADING SYSTEM 9740 SOFTWARE IN A MULTI-NODE SYSTEM

6 C1547M (7/03) UPGRADING SYSTEM 9740 SOFTWARE IN A MULTI-NODE SYSTEM NOTE: Any external computer interface (such as an access control system, alarm system, fire system, building management/ control system, or VMX200) that is using the P protocol to communicate with a CM9740-CC1 running version 7.8 ...

Page 13 - cd network; Del

C1547M (7/03) 9 (b) Verify that the 9760NIU.EXE or NET9760.EXE file was renamed to 9760NIU.OLD or NET9760.OLD,respectively, by entering: dir/w (2) Insert the System 9760 Network Disk, version 8.03.012, into the disk drive of the NW1. (3) Copy the executable file, 9760NIU.EXE, from the Network Disk t...

Page 14 - APPENDIX A. UPGRADING CM9740-MXB FIRMWARE; You do; not

10 C1547M (7/03) APPENDIX A. UPGRADING CM9740-MXB FIRMWARE CAUTION: Only qualified personnel observing electrostatic discharge (ESD) precautions should perform the proce- dure below. Always wear a grounding strap connected to an approved grounding source when working on or nearexposed electronic com...

Page 16 - Reset; button on the card (refer

12 C1547M (7/03) 5. Reinstall the video output card into slot 17 of the matrix bay (refer to Figure 2): a. Align the top and bottom edges of the card with the top and bottom card guides of the matrix bay. b. Slide the card toward the rear of the matrix bay until the card is seated firmly with the co...

Page 17 - CONNECTING AN ACD DB9 PORT TO A CM9740-CC1 DB9 PORT

C1547M (7/03) 13 APPENDIX B. CONNECTING AN ASCII COMMUNICATIONS DEVICE TO THE CM9740-CC1 As stated previously in this manual, version 8.03.012 of CM9740-CC1 software is not compatible with version 3.20 or earlier ofCM9760-DT/CM9760-DT4 software. If you wish to replace the existing DT/DT4 device (ext...

Page 18 - Connect the 9-pin side of the PV130 converter to a DB9 port of the ACD.

14 C1547M (7/03) CONNECTING AN ACD DB9 PORT TO A CM9740-CC1 RJ-45 PORT To connect an ACD DB9 port to a CM9740-CC1 RJ-45 port, refer to Figure 6 and do the following: 1. Connect the 9-pin side of the PV130 converter to a DB9 port of the ACD. 2. If necessary, connect a +12 VDC power supply to the PV13...

Page 19 - WARRANTY AND RETURN INFORMATION; REVISION HISTORY

C1547M (7/03) 15 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material orworkmanship for a period of one year after the date of shipment. Exceptions to this warranty areas noted below: • Five years on Pelco manufactured ca...