Pelco CM9740-CC1 - Manuals

CM9740-CC1 | 5 1.0 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Installation and servicing should only be done by qualified ser vice personnel and con-form to all local codes. 2. Unless the unit is specifically marked...

6 | C1508M-A (02/01) 2.0 OVERVIEW 2.1 INTRODUCTORY REMARKS The CM9740-CC1 is the controller for the System 9740™ Matrix switching system. Althoughthe CM9740-CC1 has a smaller hardware footprint than the CM9760-CC1, it can, with its“9740 specific” executable software, interface the same peripheral mi...

CM9740-CC1 | 7 3.0 BEFORE YOU BEGIN 3.1 A BRIEF NOTE The CM9740-CC1 is a nonexpandable CPU, optimized for systems ranging froma 16 x 4 configuration (16 inputs and 4 outputs) to a 256 x 32 configuration (256 in-puts and 32 outputs). Beginner or New to 9740 If you are totally new to Pelco, or are fam...

8 | C1508M-A (02/01) 4.0 INTRODUCTION TO THE CC1 4.1 DESCRIPTION The CM9740-CC1 Controller is the main component and central operating hub of the Sys-tem 9740. All components of the system connect to and communicate with the Controllervia the por ts located on the rear of the unit. The CM9740-CC1 Co...

CM9740-CC1 | 9 Rear View The rear of the controller appears as illustrated in Figure 2. This is the business end of the CM9740-CC1. Figure 2Rear View, General Identification (RS-232 Wiring Connection between the CC1 and an External PC) RX RX TX TX Refer to Figure 3 for COM port pinout identification

CM9740-CC1 | 11 4.5 CONNECTING TO THE CONTROLLER All system devices connect to the rear of the CM9740-CC1 controller . In gener al, any con-nectable device that can be used with the CM9760-CC1 can also be used with theCM9740-CC1. D-type, 9-pin connectors are used f or COM 1 and COM 2, while the VGA ...

12 | C1508M-A (02/01) 5.0 PHYSICAL INSTALLATION AND INITIALIZATION 5.1 CC1 INSTALLATION–CATEGORY I Pr eliminary For new installations, you normally receive a configuration setup or dia-g ram and a por t assignment sheet for your specific installation. Pay closeattention to these when setting up your...

CM9740-CC1 | 13 5.1.2 Categor y I–Upgrade Replacement (Hardware Only) Object: Physical Replacement of the CC1 Assumptions: • The CC1 to be replaced is par t of an existing operational system configu-ration that has failed. • The software environment that existed on the failed CC1 is to be used onthe...

14 | C1508M-A (02/01) 5.1.3 Categor y I–Upgrade Replacement (Har dware and Software) Object: Physcial replacement of the CC1, in conjunction with softw are upgrade or re- placement. Assumptions: • The CC1 to be replaced is par t of an existing, operational, system configuration. • The operational so...

16 | C1508M-A (02/01) 6.0 CC1 INITIALIZATION The initialization process occurs during the time that the CM9740.EXE program is bootingup. During this time configuration files and diagnostic programs are loaded enabling systemparameters for CCTV matr ix operation. As the initialization process proceed...

CM9740-CC1 | 17 6.1.3 MGR Program System Window That leaves the MGR system window, which ispar t of the MGR program proper. If you have anexternal PC connected to the CC1 that containsthe MGR program, there are multiple indications ofonline status associated with this program that canbe checked. Jus...

18 | C1508M-A (02/01) Figure 10Initialization–Online Nodes Figure 11MGR Windows–A Precaution 6.1.5 Online Node Dialog Box If you close the Configuration File menu and click onthe Nodes icon on the MGR program toolbar, y ou will see what appears in Figure 10. This indicates the node number and the as...

CM9740-CC1 | 19 6.1.6 Single-Node Hot Switch Configurations Refer back to Figure 7 and note the information in the lower right-hand corner of thediagnostic screen. Specifically, note the A OFF phrase. This means “AsynchronousOFF,” which means the CC1 is not part of a hot s witch configuration. If, h...

20 | C1508M-A (02/01) 7.0 CC1 CONTROLLER OPERATION The center of 9740 system operation is the CC1 controller. Monitoring operations and perfor ming housekeeping chores are important par ts of main-taining the CC1 and system integrity. First, we will discuss the tools used to monitor CC1operation in ...

CM9740-CC1 | 23 7.1.2.1 Monitor Box Examples Figure 15 shows a normal online diagnostic screen. If a CM9760-KBD connected to thesystem is using monitor 4 for camer a display, the FWD and BWD buttons on the k eyboardcan be used to cycle through the available cameras . On the diagnostic screen, the co...

24 | C1508M-A (02/01) 7.1.2.2 Monitor Box Allocation Monitor boxes can be re-allocated. To do so,perform the following steps: Press one of the F x ke ys (F1 through F8, as illustrated in Figure 17, show the relation-ship of the Fx key and Monitor box alloca- tion) that corresponds to the number of t...

28 | C1508M-A (02/01) For example, if system time in step 7 had read 2:02.30 (2 minutes and 30 seconds after2 PM) at the time RTC time read 2 PM, then we kno w that system time, over the next 24hours, must be slowed by 2 minutes and 30 seconds to synchronize system and R TC time. To accomplish that,...

CM9740-CC1 | 29 For multi-node situations, time adjustments are carr ied out utilizing the CC1 containing theNIU. The NIU, in turn, pro vides to the rest of the network the parameters for displaying sys-tem time. The time for the system is updated each minute by the NIU, which, of course , isinitial...

30 | C1508M-A (02/01) 3. When the Save & Send bar tab is pressed, a splash screen appears and in the Sys- tem Window of the MGR program, the follo wing message appears: DYNREQ Monitor code OK from Node 1 4. If there are no more changes, close the Configuration dialog windo w. When you do,the fol...

CM9740-CC1 | 33 APPENDIX I – INSTALLING THE MGR PROGRAM The reason the installation of the MGR program is reiterated here is that the 9740 DOS executable on the CC1 and the Windows ® 95 based MGR program interact. If an external PC containing the MGR program is connected to a COM por t on the CC1, t...

34 | C1508M (02/01) APPENDIX II – DOS ENVIRONMENT AND COMMANDREFERENCE DOS is an acronym for D isk O perating S ystem. Every time y ou turn on the CM9740-CC1 or every time y ou reboot (Alt + Ctrl + Delete), thecomputer loads DOS from disk (the CC1’s dr ive) into memor y (RAM).Once loaded, DOS lets y...

CM9740-CC1 | 35 ➤ A Closer Look at AUTOEXEC.BAT andthe BOOT Process The AUTOEXEC.BAT file is the last file called dur ing the boot process as described in thepre vious section. For CC1s configured as par t of a system node at the factory, the end re-sult of this process is the appearance of the CM97...

36 | C1508M (02/01) The PATH Statement The PATH statement causes DOS to look in each of the directory paths listed there for an yexecutable [.EXE, .COM or .BAT file] it’s instructed to carr y out. The syntax of the PATHstatement is as follows: PATH = { [drive:]path; [drive:]path; [drive:]path…..] } ...

CM9740-CC1 | 37 The “ \ ” symbol, when used alone represents the root director y; otherwise it indicates sepa-ration of v arious levels of the director y tree, collectively known as the dir ectory path . The result of the above entry takes you directly to the root directory and the f ollowingscreen ...

CM9740-CC1 | 43 APPENDIX V – REMOVING AN EXISTING MGR PROGRAM

44 | C1508M (02/01) APPENDIX VI – EDITING THE AUTOEXEC.BAT FILE

CM9740-CC1 | 45 Figure 27CC1 Connections–Exercise I APPENDIX VII – EXERCISES The Directory Structure of the CC1 – Exer cise I Take the CC1 that came with your order and hook it up according to the illustration in Figure 27. Figure 28CC1 Setup–Final When finished, your hook-up should look something l...

46 | C1508M (02/01) Next, hold the CTRL ke y on the keyboard do wn and, at the same time, press the Q key.***This action exits the System 9740 program and the associated diagnostic screen and takesyou to the following DOS prompt: C:\9740>_ You should arrive at this prompt using any CC1 received f...

CM9740-CC1 | 47 Directory Structure Hands-On – Exercise II Figure 29 is a sample director y tree which represents the file structure of theCC1. Pay no attention to the VGA CAP directory and its CAPS subdirector y. Itdoesn’t exist on your hard dr ive . It’s an extraneous DOS screen capture utilitytha...

48 | C1508M (02/01) 9740 Directory Flat File s Note that in addition to the previously mentioned CM9740.exe, which is the system ex-ecutable, there are a group of files, all of which have a common TEST prefix. These arethe flat files that the system program uses to configure the system f or operatio...

50 | C1508M (02/01) TESTPORT Directory The TESTPORT directory contains files that can be used to testwhether or not the RJ-45 communication ports on the rear of the CC1are good. If you issue a dir command while in the TESTPORT direc- tor y, you should see something lik e to the follo wing: The MGR a...

CM9740-CC1 | 51 Figure 34MGR Program Location Reading in Your Configuration Files After the MGR program is installed, a 9740MGR Pelco icon should appear on your desktop.If it is not there, look f or the 9740MGR folder in the root director y of your C drive (refer toFigure 34). The 9740MGR applicatio...

52 | C1508M (02/01) 9.0 SPECIFICATIONS ELECTRICAL Processor: CPU Clock Speed: 133 MHz or better Memory: 16 MB RAM Disk Drive: 3.5-inch, 1.44 MB Hard Drive: 16 MB Monitor Output: VGA (VGA graphics card supplied, monitor is not supplied) I/O Ports: 16 RS-422 ports on tw o SerCom boards, expandable to ...

54 | C1508M (02/01) 10.0 WARRANTY AND RETURN INFORMATION REVISION HISTORY Manual # Date Comments C1508M 6/00 Original version. C1508M-A 02/01 Updated to include certification information. Pelco, the Pelco logo, Spectra, Genex, Legacy, Esprit, Camclosure, and PelcoVision are registered trademarks of ...