Pelco CM9740-CC1 - Manual

Pelco CM9740-CC1

Pelco CM9740-CC1 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
Page: / 54

Table of Contents:

  • Page 2 – CONTENTS; Section; APPENDIX II
  • Page 3 – LIST OF ILLUSTRATIONS; Figure
  • Page 4 – LIST OF TABLES; Table; LIST OF APPENDIXES; Number; APPENDIX I
  • Page 5 – IMPORTANT SAFEGUARDS AND WARNINGS; Only use replacement par ts recommended by Pelco.; REGULATORY NOTICES; Reor ient or relocate the receiving antenna.
  • Page 6 – INTRODUCTORY REMARKS; New System Installation; vidual; CC1 Replacement Installation; within an existing system installation. We don’t; CATEGORY I
  • Page 7 – BEFORE YOU BEGIN; A FEW WORDS OF ADVICE AND SOME EXERCISES; The system initializes .; NOW; Flat files are information
  • Page 8 – INTRODUCTION TO THE CC1; The internal cards are manu-; CPU; Front View
  • Page 9 – Rear View; The rear of the controller appears as illustrated in Figure 2.; RX
  • Page 11 – CONNECTING TO THE CONTROLLER
  • Page 12 – PHYSICAL INSTALLATION AND INITIALIZATION; CC1 INSTALLATION–CATEGORY I; Pr eliminary; Utility Disk; Apply power to the CC1.; Remember that each peripheral device
  • Page 13 – again
  • Page 14 – Remove your old MGR software according to Appendix V.
  • Page 16 – CC1 INITIALIZATION
  • Page 17 – System Window; not
  • Page 18 – Nodes; icon on the MGR program toolbar, y ou
  • Page 19 – hot s witch configuration.; is; part of a hot switch configuration, that portion of the diagnostic; The diagnostic monitor and
  • Page 20 – CC1 CONTROLLER OPERATION; MONITORING CC1 FUNCTIONS; Description
  • Page 23 – A CAUTIONARY NOTE
  • Page 24 – Allocation; Press one of the; F x; Box 1 allocated to Physical Monitor 3
  • Page 28 – General Remarks Regarding System Time Adjustment
  • Page 29 – CC1 SYSTEM INTEGRITY; Save Send; Dynamically Updating a Configuration File; Press the; Configuration File Dialog Box
  • Page 30 – DYNREQ Monitor code OK from Node 1; Click on the Send Update Request bar tab.; UPDT HardDrv Monitor File OK from Node 1.
  • Page 33 – APPENDIX I – INSTALLING THE MGR PROGRAM
  • Page 34 – The Boot Process; IMPORTANT NOTE
  • Page 35 – DOS Commands; Invoking the CM9740 Executable; REM; at the beginning of a line, the line is ignored when; File Names and DOS; The prompt command line in the figure above con-
  • Page 36 – which puts you at the screen prompt in the BKUPTST directory:
  • Page 37 – Manipulating Files in the DOS Environment
  • Page 41 – APPDENDIX III – MGR WRITE UTILITY
  • Page 42 – APPENDIX IV – MGR READ UTILITY
  • Page 43 – APPENDIX V – REMOVING AN EXISTING MGR PROGRAM
  • Page 44 – APPENDIX VI – EDITING THE AUTOEXEC.BAT FILE
  • Page 45 – APPENDIX VII – EXERCISES; The Directory Structure of the CC1 – Exer cise I; If this looks a lot like a standard PC setup to you, you’re right, it is.; ing a CCTV matr ix system.
  • Page 46 – ENTER; This is called the; root; Preliminaries – Exer cise I; The location of important files and programs on the CC1.; The executable for; NOT; a Windows environment; DOS
  • Page 47 – press the
  • Page 48 – Ctrl; flat
  • Page 50 – TESTPORT Directory; dir; command while in the TESTPORT direc-; The MGR and Your System Configuration Files (Flat Files)–; 5 installed on it; Loading the MGR
  • Page 51 – Reading in Your Configuration Files; Double-click on the MGR icon and the MGR program starts .
  • Page 52 – ELECTRICAL; MECHANICAL
  • Page 54 – WARRANTY AND RETURN INFORMATION; REVISION HISTORY; PRODUCT WARRANTY AND RETURN INFORMATION
Loading the manual

CM9740-CC1

System 9740™

Controller

Installation/

Operation Manual

C1508M-A (02/01)

®

Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com

In Nor th Amer ica and Canada: Tel (800) 289-9100 • FAX (800) 289-9150

International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - CONTENTS; Section; APPENDIX II

2 | C1508M-A (02/01) CONTENTS Section Page 1.0 IMPORTANT SAFEGUARDS AND W ARNINGS ...................................................... 51.2 REGULATORY NOTICES .............................................................................. 5 2.0 OVERVIEW ................................................

Page 3 - LIST OF ILLUSTRATIONS; Figure

CM9740-CC1 | 3 LIST OF ILLUSTRATIONS Figure Page 1 CM9740-CC1 Front Vie w ................................................................................... 8 2 Rear Vie w, General Identification ....................................................................... 9 3 CM9740-CC1 Rear Connector P...

Page 4 - LIST OF TABLES; Table; LIST OF APPENDIXES; Number; APPENDIX I

4 | C1508M-A (02/01) LIST OF TABLES Table Page A Command Key Functions .................................................................................. 25 B CC1 Hardware Errors ........................................................................................ 32 C CC1 System Errors ............

Other Pelco Models

All Pelco Other