Peavey U1002 - Manuals - manualsarea.com

Page 8 - Included Accessories:

8 1. INTRODUCTION Thank you for choosing the most advanced wireless microphone system from Peavey. In today's audio world, the demand for operating many wireless microphone systems simultaneously is greatly increasing. Furthermore, audio engineers would like to have a unit that has easy frequency ag...

Page 9 - PART NAMES AND FUNCTIONS; placement on OPTIONAL rack-mount brackets.

9 2. PART NAMES AND FUNCTIONS Front Panel: (1) Front Antenna Input Connectors (A and B): located on optional rack-mount ears: Allows an optional rear-to-front Antenna kit for front antenna placement on OPTIONAL rack-mount brackets. (2) Power Switch and Indicator: When switch is turned on, the red in...

Page 11 - INSTALLATION OF THE RECEIVER; These

11 3. INSTALLATION OF THE RECEIVER (1) Install the two antennas to the antenna sockets (4) on the rear panel, illustrated in Fig. 3 or on front rack-mount ears (1). Caution: These sockets have 8 Volts DC supplied to them, which enables you to directly connect the Peavey antenna booster for antenna r...

Page 17 - make sure all transmitters that are to be used are powered up.; the upper right corner of the display.

17 Selecting/Changing CHANNEL: NOTE: In order for the receiver to recognize that a frequency is occupied, make sure all transmitters that are to be used are powered up. Press the "MENU" button until the "G/CH" function is selected. This will be indicated by a block that will appear a...

Page 18 - Viewing Channel FREQUENGY:; Too high of a level will cause the audio signal to become choppy and

18 Viewing Channel FREQUENGY: Press the "MENU" button until the "FREQ" function is selected. This will be indicated by a block that will appear around the selected function located in the upper right corner of the display. The frequency displayed will be for that particular channel f...

Page 23 - prevents inadvertent or unintentional changes to the settings.; Status Indicators; The meter to the right (next to RF meter) indicates the strength of

23 Selecting/Changing LOCK/UNLOCK: Press and hold the "MENU" button until the word "LOCK" appears momentarily on the panel. At that point only the "CCS" button is active. This prevents inadvertent or unintentional changes to the settings. Press and hold the "MENU" but...

Page 24 - COMPUTER NETWORK INTERFACE OPERATION; the RS-232 or USB COM PORT on the computer as illustrated in Fig. 10

24 7. COMPUTER NETWORK INTERFACE OPERATION (1) Connect the network interface remote connector (8) on the back of the receiver to the interface converter (this requires at least two linking cables for each pairing). Then use RJ 11 telephone cable to connect the converter to the RS-232 or USB COM PORT...

Page 25 - System Requirements:

25 System Requirements: • Windows 98R, Windows 2000R • 32MB RAM Minimum (64MB is recommended) • CD-ROM 2X or higher • At Least one nine-pin D-Sub RS-232 port (for RJ-11/RS-232 Converter) 8. CAUTIONS (1) When using the DC power supply, please be aware of the operating voltage. Make sure that a minimu...

Page 26 - PART NAMES AND FUNCTIONS; (2) Handle Housing: Houses electronics and battery compartment; BATTERY INSTALLATION; attach battery cap as illustrated in Fig. 2.

26 1. PART NAMES AND FUNCTIONS (1) Grille: Protects microphone capsule and reduces "POP" noise. (2) Handle Housing: Houses electronics and battery compartment (3) LCD Display: Indicates function information such as Error, Group ID, Channel ID, Battery Status and Power Off (4) Battery Compart...

Page 29 - to extend battery life.

29 1. PART NAMES AND FUNCTIONS (1) AF Input Jack: Connects to lavalier, headset microphones or to guitar cable. (see P23 for five different ways of connecting the TA4F AF input connector). (2) Power Switch: Powers up unit. Switch to OFF position when not in use to extend battery life.

Page 31 - compartment as illustrated in Fig.3

31 (11) Detachable Belt Clip: Allows for 360 degrees of rotation to suit transmitting angles. To detach, simply use a screwdriver on a 45-degree angle to unfasten (see Fig. 2). 2. BATTERY INSTALLATION (1) Push in on both battery cover snap locks (10) to open battery compartment as illustrated in Fig...

Page 32 - OPERATING INSTRUCTIONS

32 (2) Insert two 1.5 Volt (AA) batteries into the battery compartment, being careful of the proper polarity as illustrated in Fig.4 NOTE: When transmitter is not in use, make sure it is switched off. If the transmitter will not be used for some time, please remove the batteries from the battery com...

Page 34 - FUNCTIONS OF LCD DISPLAY; diagnose which error you are experiencing

34 5. FUNCTIONS OF LCD DISPLAY (1) "ERR" Message: When "ERR" appears in the display it indicates that an operational error has occurred. Please refer to the following codes to diagnose which error you are experiencing ERR no01 - EEPROM is not being programmed or internal data error. ...