Peavey Studio - Manuals - manualsarea.com

Page 3 - IMPORTANT SAFETY INSTRUCTIONS; SAVE THESE INSTRUCTIONS!

IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only w...

Page 4 - WICHTIGE SICHERHEITSHINWEISE; BEWAHREN SIE DIESE SICHERHEITSHINWEISE AUF!

WICHTIGE SICHERHEITSHINWEISE ACHTUNG: Beim Einsatz von Elektrogeräten müssen u.a. grundlegende Vorsichtsmaßnahmen befolgt werden : 1. Lesen Sie sich diese Anweisungen durch. 2. Bewahren Sie diese Anweisungen auf. 3. Beachten Sie alle Warnungen. 4. Befolgen Sie alle Anweisungen. 5. Setzen Sie dieses ...

Page 5 - INSTRUCTIONS IMPORTANTES DE SECURITE; GARDEZ CES INSTRUCTIONS!

INSTRUCTIONS IMPORTANTES DE SECURITE ATTENTION: L’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. Lire ces instructions. 2. Gardez ce manuel pour de futures références. 3. Prétez attention aux messages de précautions de ce manuel. 4. Suivez ces instruct...

Page 6 - INSTRUCCIONES IMPORTANTES PARA SU SEGURIDAD; GUARDE ESTAS INSTRUCCIONES!

INSTRUCCIONES IMPORTANTES PARA SU SEGURIDAD CUIDADO: Cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. Guarde estas instrucciones. 3. Haga caso de todos los consejos. 4. Siga todas las instrucciones. 5. No usar este aparato ...

Page 7 - ENGLISH

ENGLISH 7 Windsor Studio™ All-Tube Combo Amplifier Congratulations on your purchase of the new Windsor Studio tube combo amplifier from Peavey. The Windsor Studio offers more “bang for your buck” than any other combo amp on the market and the tones that you will experience from this 1 x 12” Class A ...

Page 8 - Front Panel

8 High Gain Input - Used for most electric guitars. It is 10dB more sensitive than the LOW GAIN INPUT (2). Low Gain Input - Provided for instruments that have extremely high outputs, which may result in overdriving or distorting the HIGH GAIN INPUT (1). If both inputs are used simultaneously, the le...

Page 9 - Power Switch; WARNING

Reverb - Controls the amount of reverberation that is mixed into the signal path. Pilot Light - Illuminates when AC power is being supplied to the amplifier. Standby Switch - Placing this switch in the “STANDBY” position will effectively shut the amplifier off while keeping all heater and bias suppl...

Page 10 - Rear Panel; AC Power Inlet

10 Rear Panel AC Power Inlet - This is the receptacle for an IEC line cord, which provides AC power to the unit. Connect the line cord to this connector to provide power to the unit. Damage to the equipment may result if improper line voltage is used. (See line voltage marking on unit). Never break ...

Page 11 - Recording Output

11 Rear Panel Recording Output - This balanced XLR jack is used to route a microphone-simulated signal (tapped directly from whatever speaker is being used) from the amplifier to an external recording device or PA. It utilizes a 100% passive circuit to avoid clipping, noise, and other shortcomings o...

Page 12 - Guitar Amplifier; Suggested Settings

12 Windsor ™ Studio Guitar Amplifier Suggested Settings 1.) Thick Clean / Classic Lead: Preamp Volume = 5 - 7 Bass = 11 - 12 Middle = 5 - 7 Treble = 5 - 7 Master Volume = Adjust to taste. 2.) High Gain / Hard Rock: Preamp Volume = 9 - 11 Bass = 7 - 9 Middle = 7 - 9 Treble = 5 - 7 Master Volume = Adj...

Page 13 - SPECIFICATIONS; Rated Power and Tube Compliment

13 Windsor ™ Studio Guitar Amplifier SPECIFICATIONS Rated Power and Tube Compliment 14-16W (rms) with the following: EL34 (stock), KT77,6CA7, CV1741, CV741, E34L. 10-12W (rms) with the following: 6L6GC, 5881, KT66, 7581, 5932, N66, EL37, DL37, CV1947, CV1075, CV586. 17-20W (rms) with the following: ...

Page 15 - PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY

15 Logo referenced in Directive 2002/96/EC Annex IV (OJ(L)37/38,13.02.03 and defined in EN 50419: 2005 The bar is the symbol for marking of new waste and is applied only to equipment manufactured after 13 August 2005 8IBU5IJT8BSSBOUZ$PWFST :PVS1FBWFZ8BSSBOUZDPWFSTEFGFDUTJONBUFSJBMBOEXPSLNBOTIJQJO1FB...