Patton 2702 G.703 - Manuals

Page 2 - WARRANTY STATEMENT

PATTON MODEL 2702 TABLE OF CONTENTS Section Page 1.0 General Information ...............................................................2 1.1 Warranty Statement1.2 Radio and TV Interference1.3 CE and Telecommunication Approvals1.4 Service Information 2.0 General Information ............................

Page 3 - RADIO AND TV INTERFERENCE; The Model 2702 generates and uses radio frequency energy, and; CE AND TELECOMMUNICATION APPROVALS; The CE symbol on your Patton Electronics equipment indicates; SERVICE INFORMATION; All warranty and non-warranty repairs must be returned freight

1.2 RADIO AND TV INTERFERENCE The Model 2702 generates and uses radio frequency energy, and if not installed and used properly-that is, in strict accordance with themanufacturer's instructions-may cause interference to radio and televi-sion reception. The Model 2702 has been tested and found to comp...

Page 4 - GENERAL INFORMATION; GENERAL PRODUCT DESCRIPTION; Customer Site

2.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warrant-ed for One Year parts and labor. If any questions arise during installa-tion or use of the unit, contact Patton Electronics Technical Services ...

Page 5 - DIP SWITCH CONFIGURATION; DIP Switches; OFF; Switch SW1: Line Coding

3.0 CONFIGURATION The Model 2702 features configuration capability via hardware switches . This section describes all possible hardware switch configu-rations of the Model 2702. 3.1 DIP SWITCH CONFIGURATION The Model 2702 has eight internal DIP switches that allow configu- ration for a wide range of...

Page 6 - SW3 is used to along with SW4 to determine the clock mode. For; CLOCK MODE SETTINGS; SIGNAL; Signal Name

Switch SW3 and SW4: Clock Mode SW3 is used to along with SW4 to determine the clock mode. For example the Model 2702 can be set to external clock mode by settingboth SW3 and SW4 to the on position. Please refer to the Clock Modechart below for the desired settings. CLOCK MODES Network Clock Transmit...

Page 7 - POWER CONNECTION; The Model 2702 offers three ways to supply external power: AC; LED DESCRIPTIONS; The Model 2702 is equipped with seven LED indicators that moni-; TXD; Figure 4. Top of Model 2702, Showing LED Indicators

4.3 POWER CONNECTION The Model 2702 offers three ways to supply external power: AC power, DC power and interface power. 4.3.1 Using the AC Power Supply (100-240VAC) The Model 2702 uses a 5VDC, 400mA universal input 100- 240VAC, power supply (center pin is +5V). The universal input powersupply is equ...

Page 9 - APPENDIX A; SPECIFICATIONS; APPENDIX B; CABLE RECOMMENDATIONS; general guideline only.

15 APPENDIX A PATTON MODEL 2702 SPECIFICATIONS Network Data Rate: 2.048 Mbps + 50ppm Network Connector: RJ-48C Nominal Impedance: 120 ohm (75 ohm available when usingPatton Model 460 Balun) DTE/DCE Interface: V.35 (DCE Orientation) on Male M/34 Line Coding: Selectable AMI or HDB3 Line Framing: G.703...

Page 10 - APPENDIX C; FACTORY REPLACEMENT PARTS; APPENDIX D; INTERFACE PIN ASSIGNMENT; Signal

17 APPENDIX C PATTON MODEL 2702 FACTORY REPLACEMENT PARTS AND ACCESSORIES Patton Model # Description 2702/CM/UI .....................V.35 to E1 Converter (V.35 M/34 Male, UI) 10 - 09F ...........................6 Foot Control Port Cable, 25 mm to DB9F 07M2702 .........................User Manual 080...

Page 11 - POWER SUPPLY INTERFACE; Ground; Jumper Position for Power via Pin KK:; power supply jumper on the printed cir-

19 APPENDIX D (( c c o o n n tt ii n n u u e e d d )) PATTON MODEL 2702 INTERFACE PIN ASSIGNMENT M/34 Connector, Terminal Interface Pin # Signal A GND (Earth Ground/Shield) B SGND (Signal Ground) D CTS (DCE Source) E DSR (DCE Source, Always On) F CD (DCE Source) L LL (Local Loop, DTE Source) M TM (T...