Patton 2158B - Manuals - manualsarea.com

Page 2 - CONTENTS

2 CONTENTS 1.0 Warranty Information ................................................................. 4 1.1 Regulatory Information ................................................................. 4 EMC Directive:.............................................................................. 4Low-Vol...

Page 4 - warrants all Model 2158B components to be free; be liable for any damages incurred by the use of this; Patton Electronics; Note; Conformity documents of all Patton products can be viewed; REGULATORY INFORMATION; • FCC Part 15, Class A

4 1.0 WARRANTY INFORMATION Patton Electronics warrants all Model 2158B components to be free from defects, and will—at our option—repair or replace the product should it fail within one year from the ﬁrst date of the shipment. This warranty is limited to defects in workmanship or materials, and does...

Page 5 - Packages received without an RMA number will not be

5 of Part 15 of FCC rules, which are designed to provide reasonable pro-tection from such interference in a commercial installation. However, there is no guarantee that interference will not occur in a particular instal-lation. If the device does cause interference to radio or television recep-tion,...

Page 6 - SAFETY WHEN WORKING WITH ELECTRICITY; WARNING

6 1.6 SAFETY WHEN WORKING WITH ELECTRICITY • This device contains no user serviceable parts. This device can only be repaired by qualiﬁed service person-nel. • Do not open the device when the power cord is con-nected. For systems without a power switch and without an external power adapter, line vol...

Page 8 - GENERAL INFORMATION; • Variable rate CopperLINK extender - Easy to configure

8 2.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and is warranted for one year for parts and labor. If any questions or problems arise during installation or use of this product, contact Patton Electronics...

Page 9 - To install the 2158B Ethernet Extender, do the following:; See Figure 2 for the standalone unit’s rear panel arrangements.; CAUTION

9 Figure 1. Typical application The pair of 2158B models work together to create a transparent extension between two peered Ethernet LANs. Figure 1 shows a typical point-to-point application. 3.0 INSTALLATION To install the 2158B Ethernet Extender, do the following: 1. Connect the line interface bet...

Page 10 - CONNECTING THE TWISTED-PAIR LINE INTERFACE; Actual distance and link performance may vary depending on; The Model 2158B units work in pairs. One of the units must be; Power

10 Figure 2. Model 2158B standalone rear panel 3.1 CONNECTING THE TWISTED-PAIR LINE INTERFACE The Model 2158B supports communication between two peer Ethernet LAN sites over a distance of up to 3,750 ft (1.1 km) over 24 AWG (0.5 mm) twisted-pair wire. Note Actual distance and link performance may va...

Page 13 - Switch toggle; ON; Rear

13 Figure 5. Removing protective cover Figure 6 on page 13 shows the orientation of the DIP switches in the On and Off positions. Figure 6. DIP switch orientation Power Link Ethernet Cop per LIN K™ Hig h S pee d Eth ern et E xte nde r 1 2 3 4 ON Push toggle upfor ON position Switch toggle Push toggl...

Page 14 - CONFIGURING DIP SWITCH S1; Position

14 4.2 CONFIGURING DIP SWITCH S1 DIP switch S1 is where you conﬁgure the CopperLINK line. The following table describes the conﬁguration for the 2158B. S1-2: Impulse Noise Protection • Fast Mode: Direct data transmission with latency less than 1ms • Interleave Mode: Provides data transmission protec...

Page 15 - FRONT PANEL LED STATUS MONITORS

15 5.2 FRONT PANEL LED STATUS MONITORS The Model 2158B features six front panel LEDs that monitor power, the Ethernet signals, the CopperLINK connection, and the remote/local set-ting. Figure 7 shows the front panel location of each LED. Table 2 on page 15 describes the LED functions. Figure 7. Mode...

Page 16 - APPENDIX A; SPECIFICATIONS; A.2 TRANSMISSION LINE; Distances depend on selected line rate and line conditions. See; A.4 LED STATUS INDICATORS; External AC and DC options:; A.6 TEMPERATURE RANGE

16 APPENDIX A SPECIFICATIONS A.1 LAN CONNECTION • Two shielded RJ-45, 10/100Base-T, IEEE 802.3 Ethernet • CopperLINK Connection: Shielded RJ-45 A.2 TRANSMISSION LINE Two-wire unconditioned twisted pair. A.3 COPPERLINK DISTANCE • Distance: 3,750 ft (1.1 km) at 10 Mbps upstream/10 Mbps downstream Note...

Page 17 - APPENDIX B; MODEL 2158B SERIES FACTORY; Description

17 APPENDIX B MODEL 2158B SERIES FACTORY REPLACEMENT PARTS AND ACCESSORIES *Only required with optional UI power supply (08055DCUI) Patton Model # Description Base Models 2158B/E CopperLINK Multi Rate 100 Mbps Ethernet Extender; No power supply 2158B/E-2PK CopperLINK Multi Rate 100 Mbps Ethernet Ext...

Page 18 - APPENDIX C; MODEL 2158B SERIES INTERFACE PIN ASSIGNMENT; C.2 COPPERLINK INTERFACE

18 APPENDIX C MODEL 2158B SERIES INTERFACE PIN ASSIGNMENT C.1 10/100BASE-T INTERFACE RJ-45 • Pin 1: TX+ • Pin 2: TX- • Pin 3: RX+ • Pin 6: RX- • Pins 4, 5, 7, 8: no connection C.2 COPPERLINK INTERFACE RJ-45 • Pin 4: RING • Pin 5: TIP • Pins 1, 2, 3, 6, 7, 8: no connection

Page 19 - APPENDIX D; The actual distance and link performance may vary depending; Line Rate

19 APPENDIX D DISTANCE CHART, BASED ON 24 AWG (0.5 MM) Note The actual distance and link performance may vary depending on the environment and type/gauge of wire used. Note DS = downstream, US = upstream Line Rate Distance in feet (km) Throughput at Max Distance (bits per second) 10/10 3750 ft (1.1 ...

Page 20 - Patton Electronics Company