Omega OMB-DAQBOARD-3000 - Manuals

DaqBoard/3000 Series User’s Manual 917394 vii Table of Contents DaqBoard I nstallation Guide (p/n 1033-0940) 1 – Device Overviews Block Diagrams ….. 1-1 Connections …… 1-2 Theory of Operation…… 1-3 Daq Software …… 1-13 2 – Connections and Pinouts Overview …… 2-1 Pinout for DaqBoard/3000 Series Board...

viii 907994 DaqBoard/3000 Series User’s Manual 6 – Setpoint Configuration for Output Control Overview …… 6-1 Detecting Input Values …… 6-3 Controlling Analog, Digital, and Timer Outputs …… 6-4 P2C, DAC, or Timer Update Latency …… 6-6 More Examples of Control Outputs …… 6-7 Detection on an Analog Inp...

This product requires one of the following Operating Systems: Windows 2000 Windows XP

DaqBoard Installation Guide This guide tells how to complete the following steps for a successful installation. Step 1 – Install Software …… page 2 Step 2 – Install Boards in Available PCI Bus-Slots …… page 3 Step 3 – Configure Boards ….. page 5 Step 4 – Test Hardware ….. page 6 Reference Note: Afte...

1033-0940, rev 8.0 918494 DaqBoard Installation Guide IG- 3 Reference Note : Adobe PDF versions of user manuals will automatically install onto your hard drive as a part of product support. The default location is in the Programs group, which can be accessed from the Windows Desktop . Refer to the P...

Step 2 – Install Boards in available PCI Bus-slots IMPORTANT: Software must be installed before installing hardware. CAUTION Turn off power to, and UNPLUG the host PC and externally connected equipment prior to removing the PC’s cover and installing the DaqBoard. Electric shock or damage to equipmen...

7. Refer to the figure at the right. Align the groove in the DaqBoard’s PCI edge-connector with the ridge of the desired PCI slot, and with the PC’s corresponding rear-panel slot. 8. Push the board firmly into the PCI slot. The board will snap into position. 9. Secure the board by inserting the rear...

1. Run the Daq Configuration control panel applet. Navigation from the desktop to the applet is as follows: Start ⇒ Settings ⇒ Control Panel ⇒ Daq*Configuration (double-click) 2. Double-click on the Device Inventory’s DaqBoard1K0, 2K0, or 3K0 icon, as applicable. The DaqBoard’s Properties tab will a...

Step 4 – Test Hardware Use the following steps to test the DaqBoard. Note that these steps are continued from those listed under the previous section, “Configure Board.” 1. Select the “ Test Hardware” tab. 2. Click the “ Resource Test ” button. 3. After the test is complete, click “ OK .” System cap...

Device Overviews 1 Block Diagrams …… 1-1 Connections …… 1-2 Product Features …… 1-3 Software ……1-13 DaqView can only be used with one DaqBoard at a time. DASYLab and LabView can be used with multiple boards. For multiple board use (via custom programming) refer to the Using Multiple Devices section ...

1-2 Daq Systems and Device Overviews 988093 DaqBoard/3000 Series User’s Manual Block Diagram for DaqBoard/3005 and /3006 * Note : DaqBoard/3006 has 16 single-ended analog inputs; ±10V input range only; it has no differential input. DaqBoard/3006 has no HDMI interface. Connections Reference Note : Fo...

Product Features I/O Comparison Matrix Product or System Analog Input Channels Input Ranges Analog Output Channels Digital I/O Channels Counter Inputs Timer Outputs DaqBoard/3000 16SE / 8DE 7 2 24 4 2 DaqBoard/3001 16SE / 8DE 7 4 24 4 2 DaqBoard/3005 16SE / 8DE 7 0 24 4 2 DaqBoard/3006 16SE only 1 0...

1-4 Daq Systems and Device Overviews 988093 DaqBoard/3000 Series User’s Manual Signal I/O One 68-pin connector provides access to the 16SE/8DE analog input channels, 24 digital I/O lines, counter/timer channels, and analog outputs (when applicable). With exception of DaqBoard/3006, a HDMI connector ...

Example 3: Analog and digital channel scanning, once per scan mode The figure below shows a more complicated acquisition. The scan is programmed pre-acquisition and is made up of 6 analog channels (Ch0, Ch2, Ch5, Ch11, Ch22, Ch25) and 4 digital channels (16-bits of digital IO, 3 counter inputs.) Eac...

1-8 Daq Systems and Device Overviews 988093 DaqBoard/3000 Series User’s Manual Example 4: Sampling digital inputs for every analog sample in a scan group The figure below shows another acquisition. The scan is programmed pre-acquisition and is made up of 6 analog channels (Ch0, Ch2, Ch5, Ch11, Ch22,...

DaqBoard/3000 Series User’s Manual 988093 Daq Systems and Device Overviews 1-9 Bus Mastering DMA The DaqBoard/3000 series supports Bus Mastering DMA. Multiple DMA channels allow analog and digital/counter input data, as well as analog and digital output data to flow between the PC and the DaqBoard/3...

1-10 Daq Systems and Device Overviews 988093 DaqBoard/3000 Series User’s Manual o Variable pre-trigger with post trigger stop event . Unlike the previous pre-trigger modes, this mode does not have to satisfy the pre-trigger number of readings before recognizing the trigger event. Thus the number of ...

Digital Inputs and Outputs Twenty-four TTL-level digital I/O lines are included in each of the DaqBoard/3000 Series boards. Digital I/O can be programmed in 8-bit groups as either inputs or outputs and can be scanned in several modes (see Input Scanning ). Ports programmed as input can be part of th...

1-12 Daq Systems and Device Overviews 988093 DaqBoard/3000 Series User’s Manual This example has all 4 DACs being updated and the 16-bits of digital IO. These updates are performed at the same time as the acquisition pacer clock (also called the scan clock.) All 4 DACs and the 16-bits of pattern dig...

DaqBoard/3000 Series User’s Manual 988093 Daq Systems and Device Overviews 1-13 Timer Outputs Two 16-bit timer outputs are built into every 3000 series board. Each timer is capable of generating a different square wave with a programmable frequency in the range of 16 Hz to 1 MHz. Example 6: Timer Ou...

Connections and Pinouts 2 Overview …… 2-1 Pinout for DaqBoard/3000 Series Boards …… 2-2 TB-100 Terminal Connector Option …… 2-3 PDQ30 Analog Expansion and DBK215 Connector Options …… 2-4 CAUTION Turn off power to all devices connected to the system before connecting cables or setting configuration j...

Pinout for DaqBoard/3000 Series Boards Pin numbers refer to the 68-pin SCSI female connector, located on the DaqBoard/3000. Function Pin Pin Function Analog input Channel 8 34 68 Analog input Channel 0 Analog input Channel 1 33 67 Analog Common Analog Common 32 66 Analog input Channel 9 Analog input...

TB-100 Terminal Connector Option The TB-100 Terminal Connector option can be used to connect all signal I/O lines that are associated with a DaqBoard/3000 Series device. TB-100 connects to the DaqBoard’s 68-pin SCSI connector via a 68-conductor cable: p/n CA-G55, CA-G56, or CA-G56-6. TB-100 Pinout T...

PDQ30 Analog Expansion and DBK215 Connector Options 2-4 Connections & Pinouts 918494 DaqBoard/3000 Series User’s Manual PDQ30 Analog Expansion Module DBK215 16 BNC Connector Module DaqBoard/3000 Series boards can connect to optional devices through either or both of the board’s orb connectors. D...

DBK215 If you are not using a TB-100 terminal board connection option with your DaqBoard/3000 Series board you can, instead, make use of a DBK215 module. The DBK215 includes: o BNC Access to 16 inputs or outputs (on front panel) o on-board screw-terminal blocks* o on-board socket locations for custo...

PDQ30 Terminal Block Pinouts (TB1 through TB6) PDQ30 can measure 48 channels of voltage or 24 channels of temperature. The temperature measurement requires the use of Differential Mode. Reference Notes : For PDQ30 specifications, refer to chapter 6. DaqBoard/3000 Series User’s Manual 918494 Connecti...

CE-Compliance 3 Overview ……3-1 CE Standards and Directives …… 3-1 Safety Conditions ……3-2 Emissions/Immunity Conditions ……3-2 Overview CE standards were developed by the European Union (EU) dating from 1985 and include specifications both for safety and for EMI emissions and immunity. Now, all affec...

For clarification, terms used in some Declarations of Conformity include: • pollution degree : any addition of foreign matter, solid, liquid or gaseous (ionized gases) that may produce a reduction of dielectric strength or surface resistivity. Pollution Degree I has no influence on safety and implie...

Calibration 4 DaqBoard/3000 Series boards are factory-calibrated. However, if adjustments are needed they should be completed in the following order: 1. Analog Measurement Path, Offset and Gain 2. Voltage Reference 3. DAC0 Offset and Gain * 4. DAC1 Offset and Gain * 5. DAC2 Offset and Gain * 6. DAC3...

DaqCal User Calibration Utility Contents Overview …… i Equipment …… ii NIST Traceability …… iii Installing DaqCal …… iii Setup …… iii What to Expect when using DaqCal …… v Calibrating Analog Outputs …… vii Calibrating DBK Expansion Options …… viii CAUTION Turn off power to all devices connected to t...

pg. ii_DaqCal 918494 User Calibration Guide, 457-0931 rev 1.0 Equipment Refer to the appropriate block below, depending on whether you will be calibrating through a 37-pin, 68-pin, or 100-pin connector . P1 37-PIN If calibration signals will be passing through a 37-pin P1 connector you will need : R...

NIST Traceability Calibration test equipment should be traceable through the National Institute of Standards and Technology. (NIST). Customers not familiar with traceability through that institute should contact them at [email protected] The NIST Policy on Traceability (contained in NIST Adminis...

P1 (37-pin) For DB37 P1 applications you can attach a DBK11A to the device via a CA-37 cable. Connecting a DBK11A P4 (100-pin) For 100-pin P4 connector applications you can use a DBK200 (or DBK201), DBK11A, and a CA-195 cable; or you could use a DBK213 and a CA-195 cable. Illustrations of these two ...

After you have completed the setup according to the type of device and appropriate connectivity option, launch DaqCal and follow the on-screen instructions. What to Expect when using DaqCal When DaqCal opens you will be prompted to select your device from a list. After doing so the application will ...

Calibrating Analog Outputs After launching DaqCal, select the device to be calibrated from the device inventory list. After selecting your device, click the <OK> button. An instruction screen with a Calibration List will display. From the screen’s Calibration List select the desired types of c...

Calibrating DBK Expansion Options If the primary data acquisition device (DaqBook, or DaqBoard) is out of its calibration period, calibrate that device prior to calibrating the DBK expansion option. An alternative to using DaqCal is to contact the factory or your service representative to schedule a...

Counter Input Modes 5 Debounce Module …… 5-1 Terms Applicable to Counter Modes…….5-5 Counter Options …… 5-5 Counter/Totalize Mode …… 5-6 Period Mode …… 5-8 Pulsewidth Mode …… 5-11 Timing Mode …… 5-13 Encoder Mode …… 5-1 5 Each of the high-speed, 32-bit counter channels can be configured for counter,...

Trigger After Stable Mode In the “Trigger After Stable” mode, the output of the debounce module will not change state until a period of stability has been achieved. This means that the input has an edge and then must be stable for a period of time equal to the debounce time. Debounce Module – Trigge...

DaqBoard/3000 Series User’s Manual 918494 Counter Input Modes 5-5 Terms Applicable to Counter Modes The following terms and definitions are provided as an aid to understanding counter modes. Gating: Any counter can be gated by the mapped channel. When the mapped channel is high, the counter will be ...

Encoder Mode (see page 15). OPT[1:0] : Determines the encoder measurement mode: 1X, 2X, or 4X. OPT2 : Determines whether the counter is 16-bits (Counter Low); or 32-bits (Counter High). OPT3 : Determines which signal latches the counter outputs into the data stream going back to the /3000 Series boa...

Period Mode TIP: When using a counter for a trigger source, it is a good idea to use a pre-trigger with a value of at least 1. The reason is that all counters start at zero with the initial scan; and there will be no valid reference in regard to rising or falling edge. Setting a pre-trigger to 1 or ...

DaqBoard/3000 Series User’s Manual 918494 Counter Input Modes 5-9 PERIOD: OPT[1:0]: Determines the number of periods to time, per measurement . This makes it possible to average out jitter in the input waveform, sampling error, noise, etc. There are four options: (1) The channel’s measurement is lat...

5-10 Counter Input Modes 918494 DaqBoard/3000 Series User’s Manual Upper 16-bits of the 32-bit counter Lower 16-bits of the 32-bit counter Range (Hz) Ticksize (nS) Averaging Option Range (Hz) Ticksize (nS) Averaging Option 15u – 1500u 20833.333 1 1 – 100 20833.333 1 150u – 15m 2083.333 1 10 – 1k 208...

Pulsewidth Mode TIP: When using a counter for a trigger source, it is a good idea to use a pre-trigger with a value of at least 1. The reason is that all counters start at zero with the initial scan; and there will be no valid reference in regard to rising or falling edge. Setting a pre-trigger to 1...

5-12 Counter Input Modes 918494 DaqBoard/3000 Series User’s Manual PULSEWIDTH: OPT2: Determines whether the pulsewidth is to be measured with a 16-bit (Counter Low), or 32-bit (counter High) counter. Since pulsewidth measurements always have the “stop at the top” option enabled, this option dictates...

Timing Mode TIP: When using a counter for a trigger source, it is a good idea to use a pre-trigger with a value of at least 1. The reason is that all counters start at zero with the initial scan; and there will be no valid reference in regard to rising or falling edge. Setting a pre-trigger to 1 or ...

An Example of Timing Mode The following example represents one channel in timing mode. The time desired is between the rising edge on the input channel and the falling edge on the mapped channel . Zeroes are returned, in the scan, until one complete time measurement has been taken. At that point, th...

Encoder Mode TIP: When using a counter for a trigger source, it is a good idea to use a pre-trigger with a value of at least 1. The reason is that all counters start at zero with the initial scan; and there will be no valid reference in regard to rising or falling edge. Setting a pre-trigger to 1 or...

ENCODER: OPT[1:0]: This determines the encoder measurement mode: 1X, 2X, or 4X. ENCODER: OPT3: This determines which signal latches the counter outputs into the data stream going back to the /3000 Series board. Normally, the start of scan signal latches the counter outputs at the beginning of every ...

Wiring for 1 Encoder The following figure illustrates connections for one encoder to a 68-pin SCSI connector on a DaqBoard/3000 Series board. The “A” signal must be connected to an even-numbered channel and the associated “B” signal must be connected to the next [higher] odd-numbered channel. For ex...

A typical acquisition might take 6 readings off of the 3000 Series board module as illustrated below. The user determines the scan rate and the number of scans to take. DaqBoard/3000 Series board Acquisition of Six Readings per Scan Note : Digital channels do not take up analog channel scan time. In...

Wiring for 2 Encoders The following figure illustrates single-ended connections for two encoders. Differential connections are not applicable. Two Encoders Connected to pins on the SCSI Connector* * Connections can instead, be made to the associated screw-terminals of a connected TB-100 terminal con...

Setpoint Configuration for Output Control 6 Overview …… 6-1 Detecting Input Values …… 6-3 Controlling Analog, Digital, and Timer Outputs …… 6-4 P2C, DAC, or Timer Update Latency …… 6-6 More Examples of Control Outputs …… 6-7 Detection on an Analog Input, DAC and P2C Updates …… 6-7 Detection on an An...

DaqBoard/3000 Series boards include a setpoint configuration feature which allows the user to individually configure up to 16 detection setpoints associated with channels within a scan group. Each detection setpoint can be programmed in the following ways: o Single Point referenced – above, below, o...

Detecting Input Values All setpoints are programmed as part of the pre-acquisition setup, similar to setting up the analog path, debounce mode, or counter mode setup. Since each setpoint acts on 16-bit data, each has two 16-bit compare values: Limit A (High Limit) and Limit B (Low Limit). These limi...

Controlling Analog, Digital, and Timer Outputs Each setpoint can be programmed with an 8-bit digital output byte and corresponding 8-bit mask byte. When the setpoint criteria has been met, the P2C digital output port can be updated with the given byte and mask. Alternately, each setpoint can be prog...

The setting of a detection window must be done with a scan period in mind. This applies to analog inputs and counter inputs. Quickly changing analog input voltages can step over a setpoint window if not sampled often enough. There are three possible solutions for overcoming this problem: (1) The sca...

P2C, DAC, or Timer Update Latency Setpoints allow DACs, timers, or P2C digital outputs to be updated very quickly. Exactly how fast an output can be updated is determined by the following three factors: o scan rate o synchronous sampling mode o type of output to be updated Example : We set an acquis...

More Examples of Control Outputs Detection on an Analog Input, DAC and P2C Updates Update Mode: Update on True and False Criteria: Ch 5 example: Below Limit; Ch 4 example: Inside Window In this example Channel 5 has been programmed with reference to one setpoint [Limit A], defining a low limit; and ...

In the example [upper portion of the preceding figure], the setpoint placed on analog Channel 5 updated DAC1 with 0.0V. The update occurred when Channel 5’s input was less than the setpoint (Limit A). When the value of Channel 5’s input was above setpoint Limit A, the condition of <A was false an...

Using the Hysterisis Function Update Mode: N/A, the Hysterisis option has a forced update built into the function Criteria Used: window criteria for above and below the set limits The figure below shows analog input Channel 3 with a setpoint which defines two 16-bit limits, Limit A (High) and Limit ...

Using Multiple Inputs to Control One DAC Output Update Mode: Rising Edge, for each of 2 channels Criteria Used: Inside Window, for each of 2 channels The figure below shows how multiple inputs can update one output. In the following figure the DAC2 analog output is being updated. Analog input Channe...

DaqBoard/3000 Series User’s Manual 908794 Setpoint Configuration for Output Control 6-11 The Setpoint Status Register Regardless of which software application you are using with a DaqBoard/3000 Series device, a setpoint status register can be used to check the current state of the 16 possible setpoi...

Specifications – DaqBoard/3000 Series and PDQ30 7 DaqBoard/3000 Series Specifications I/O Comparison Matrix Product or System Analog Input Channels Input Ranges Analog Output Channels Digital I/O Channels Counter Inputs Timer Outputs DaqBoard/3000 16SE / 8DE 7 2 24 4 2 DaqBoard/3001 16SE / 8DE 7 4 2...

7-2 Specifications 988093 Note : Specifications are subject to change without notice. Maximum Usable Input Voltage + Common Mode Voltage Ranges Maximum (CMV + V in ) 0.5, 1, 2, 5, 10V 10.5V 0.1, 0.2V 2.1V A/D Specifications Type : Successive approximation Resolution : 16 bit Maximum Sample Rate : 1 ...

Note : Specifications are subject to change without notice. 988093 Specifications 7-3 External Acquisition Scan Clock Input Maximum rate : 1.0 MHz Clock Signal Range : Logical zero 0V to 0.8V; Logical one 2.4V to 5.0V; protected to ±15V Minimum pulse width : 50 ns high, 50 ns low Triggering Trigger ...

7-4 Specifications 988093 Note : Specifications are subject to change without notice. Analog Outputs Applicable to DaqBoard/3000 and /3001 only Analog output channels are updated synchronously relative to scanned inputs, and clocked from either an internal onboard clock, or an external clock source....

Pattern Generation Output Two of the 8-bit ports can be configured for 16-bit pattern generation. The pattern can be updated synchronously with an acquisition at up to 12 MHz. Counters One Counter Channel, Typical Each of the four high-speed, 32-bit counter channels can be configured for counter, pe...

7-6 Specifications 988093 Note : Specifications are subject to change without notice. Frequency/Pulse Generators One Timer Channel, Typical Channels : 2 x 16-bit Output Waveform : Square wave Output Rate : 1 MHz base rate divided by 1 to 65535 (programmable) High Level Output Voltage : 2.0V minimum ...

Note : Specifications are subject to change without notice. 988093 Specifications 7-7 PDQ30 Specifications General Operating Temperature: -30˚ to +70˚C Storage Temperature: -40˚ to +80˚C Power Consumption: 400 mW (max) Warm up: 30 minutes to rated specifications Relative Humidity: 0 to 95%, non-cond...

7-8 Specifications 988093 Note : Specifications are subject to change without notice. PDQ30 Type T Thermocouple Typical Performance of 12 PDQ30 Units; 0°C (Note 1) -1.5 -1.0 -0.5 0.0 0.5 1.0 1.5 0 5 10 15 20 Channel E rro r ( ° C ) Note 1: Assumes 16384 oversampling applied, CMV = 0.0V, 60 minute wa...

Appendix A DBK215 16-Connector BNC Connection Module With 68-Pin SCSI Adaptability for Analog I/O, Digital I/O, & Pulse/Frequency Overview …… 1 Block Diagram …… 2 Connection Tips…… 3 System Examples …… 4 Using the Screw-Terminal Blocks …… 5 Adding RC Filter Networks …… 11 Specifications …… 13 DB...

DBK215, pg. A-2 886994 Appendix A TB15 supports BNCA thru BNCD TB16 Supports BNCE thru BNCF DBK215 Block Diagram * Accessory Kit p/n 1139-0800 includes jumper wires and a screw driver. Note that the 68-pin SCSI (P5) connector typically connects to a SCSI connector via a CA-G55, CA-G56, or CA-G56-6 c...

DBK215, pg. A-4 948894 Appendix A System Example DBK215 and PDQ30 Connection to a DaqBoard/3000 Series Board Notes regarding the above system example : 1) Any of three 68-conductor SCSI ribbon cables can be used to connect the DBK215 to the board’s SCSI.. o CA-G55 is a 3-foot long cable. o CA-G56 is...

Using the Screw-Terminal Blocks You must remove the DBK215 module’s cover plate to access the screw terminal blocks. This is described in steps 1 and 2 below. 1. Remove the top inward screws from each of the 4 mounting brackets. See following figure. The Cover Plate is Secured by 4 Srews [2 Screws p...

Pulse/Frequency Correlation to 68-pin SCSI TB1 Pin Number and Description D0 N/A P3 Digital Port Bit 0 D1 N/A P3 Digital Port Bit 1 D2 N/A P3 Digital Port Bit 2 D3 N/A P3 Digital Port Bit 3 TB1 is NOT USED D4 N/A P3 Digital Port Bit 4 D5 N/A P3 Digital Port Bit 5 D6 N/A P3 Digital Port Bit 6 D7 N/A ...

Adding Resistor/Capacitor Filter Networks WARNING Disconnect the DBK215 from power and signal sources prior to installing capacitors or resistors. CAUTION Ensure wire strands do not short power supply connections to any terminal potential. Failure to do so could result in damage to equipment. Do not...

DBK215, pg. A-12 948894 Appendix A • Do not use RC filters in conjunction with additional DBK expansion accessories. • Prior to installing a resistor to the filter network you must drill a 1/16” hole through the center pinhole [beneath the board’s silkscreen resistor symbol] as indicated in the prec...

Appendix A 948894 DBK215 A-13 Specifications for DBK215 Operating Environment : Temperature : -30°C to 70°C Relative Humidity : 95% RH, non-condensing Connectors : P5 : 68-Pin SCSI Screw Terminals : 14 banks of 10-connector blocks Wire Size: 12 TO 28 AWG Dimensions : 285 mm W x 220 mm D x 45 mm H (1...

Appendix B 907994 Hardware Analog Level Trigger B-1 Appendix B Hardware Analog Level Trigger An Important Note Regarding Hardware Analog Level Trigger and Comparator Change State Issue : When the starting out analog input voltage is near the trigger level, and you are performing a rising [or falling...

WARRANTY/ DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shippin...

M 4254 / 0106 Where Do I Find Everything I Need for Process Measurement and Control? OMEGA…Of Course! Shop online at omega.com TEMPERATURE 䡺 ⻬ Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies 䡺 ⻬ Wire: Thermocouple, RTD & Thermistor 䡺 ⻬ Calibrators & Ice Point R...