Omega FP-6000 - Manuals

The linearity and accuracy of the FP-6000 Seriessensor depend on predictable flow conditions inthe pipe and proper location of the fitting. Aswith any insertion flow sensor, the pipe must be fulland generally free of air pockets. 2.1 Location of Fitting The sensor must be located in a free-flowingst...

3 (max. 30 ° ) will help to avoid these problem areas, but use caution. Excessive angles will causebearing drag at lower flow rates. On a vertical pipe run locate the sensor where theflow is upward. If downward flow is necessarythe system must be designed to prevent air/watervapor pockets from devel...

The following items are required to properly installthe OMEGA FP-6000 Series Adjustable Brass flowsensor. 3.1 Hardware, Standard Sensor • female pipe fitting (weld-on or saddle) 1 1 / 2 in. NPT or ISO 7/1-Rc 1- 1/2 • 1 1 / 4 in. (32 mm) diameter drill • Pipe thread sealant • Tape measure 3.2 Hardwar...

5 4. Remove brass sensor nut from sensor. 5. Thread brass sensor nut into pipe fitting. 3.4 Hot-Tap Fitting Installation 1. Install the pipe fitting on the outside diameter ofthe pipe according to the manufacturer's instruc-tions. Failure to follow these instructions may resultin bodily injury and/o...

6 4. Open the isolation valve and insert the drillthrough the valve and cut the sensor clearancehole. After the hole is cut, withdraw the drill fromthe isolation valve and close the valve. Removethe drilling machine per manufacturer's instructions. 5. Install brass sensor nut/bleed valve into the to...

7 Standard Sensor H = 5.95 - pipe wall thickness - (0.10 X I.D.) Example:3.0 inch schedule 80 wrought steel;Wall thickness= 0.3 in.Inside diameter = 2.9 in. H = 5.95 - 0.3 - (0.10 X 2.9)H = 5.36 in. Hot-Tap Sensor H = 15.00 - pipe wall thickness - (0.10 X I.D.) Example:10 inch schedule 40 wrought st...

8 Once the correct dimensions are calculated andrecorded, the sensor can be installed in the fitting.The Standard and Hot-Tap versions requiresubstantially different procedures. 3.6 Standard Installation 1. Thread one hex nut onto each of the threethreaded rods included in package. Installthreaded r...

9 4. Place the alignment rod in the hole on thesensor flange. Align the flange so rod is parallelto the process pipe. 5. Thread upper hex nuts with lock-washers untilthey contact the sensor flange and tighten. Checkfor proper "H" dimension and readjust if necessary. 5.95 in. (151 mm) " H...

alignment rod sensor flange process pipe (top view) The flow sensor alignment rod MUST be parallel to the process pipe as shown. direction of flow sensor flange 18 inch threaded rods 13.75 in. process pipe (side view) direction of flow alignment rod Upper hex nuts (3/16 x 1/4-20) 1/4 in. lock washer...

12 Using the Hot-Tap Installation Tool The Hot-Tap installation tool helps to lower thesensor into place against the pressure in the pipe. 1. Thread protector plate hex nuts onto each of thethree threaded rods. Adjust each hex to a heightof approximately 1 in. (25 mm) from the top ofeach rod. Remove...

13 3. Align the sensor cable with the swivel mountcable port to prevent cable pinching. Use a3/8 inch wrench or socket to turn the installationtool shaft clockwise until it is seated in the hole atthe top of the sensor flange. 4. Wearing safety face protection, slowly open the isolation valve to the...

14 4.1 Standard Sensor Removal To remove the Standard FP-6000 Series sensorfrom a depressurized empty pipe, simply removethe cap nuts and upper hex nuts located above thesensor flange. Pull up on sensor flange withtwisting motion. 4.2 Hot-Tap Sensor Removal To remove the Hot-Tap sensor safely from a...

15 5. Wearing safety face protection, turn theinstallation tool shaft counterclockwise to withdraw sensor until the sensor flange contacts the upperhex nuts. 6. Raise one lower hex and jam nut to bottom of sensor flange. 7. Close valve, remove bearing plate and tool. To remove the sensor 8. Wearing ...

5.1 Maintenance All versions of the FP-6000 series sensor requirelittle or no maintenance, with the exception of anoccasional sensor/paddlewheel cleaning. 5.2 Replacement Parts (Standard version) 1. Standard sensor assembly FP-6000, -60012. Rotor kit (bearings, shaft, retainers, and rotor included),...

17 5.3 Rotor Replacement Procedure 1. With a small pair of needle-nose pliers, firmlygrip the center of the rotor pin (axle) and with atwisting motion, bend the rotor pin into an "S"shape. This should pull the ends of the pin out ofthe shaft retainers and free the rotor assembly. 2. Remove s...

5.644 in.5.589 in.5.500 in.5.427 in.5.369 in.5.310 in.5.187 in.5.064 in.4.830 in.4.583 in.4.350 in.4.200 in.3.950 in.3.700 in.3.475 in. * 3.000 in. 18 NPS SCH 40 SCH 80 STD XS 5.600 in.5.538 in.5.442 in.5.360 in.5.296 in.5.230 in.5.094 in.4.942 in.4.688 in.4.475 in.4.275 in.4.150 in.3.950 in.3.750 i...

19 14.694 in.14.639 in.14.550 in.14.477 in.14.419 in.14.360 in.14.237 in.14.144 in.13.880 in.13.633 in.13.400 in.13.250 in.13.000 in.12.750 in.12.525 in. * 12.050 in. NPS SCH 40 SCH 80 STD XS 14.650 in.14.588 in.14.492 in.14.410 in.14.346 in.14.280 in.14.144 in.13.992 in.13.738 in.13.525 in.13.325 i...

23 Specifications General Data Flow velocity range: 1.6 to 20 ft/s0.5 to 6 m/s Linearity: ± 1% of full range Repeatability: ± 0.5% of full range Pipe sizes:Standard version: 1.5 to 24 in.(38 to 610 mm) Hot-Tap version: 1.5 to 36 in.(38 to 914 mm) Cable length: 25 ft (7.6 m), can extendup to 200 ft (...

operating pressure: 225 psi (15 bar) Maximumoperating temperature: 212 ° F (100 ° C) Caution: The FP-6002 and FP-6003 Series Hot- Tap system's overall specifications and limitationsdepend on the lowest maximum rating of thecomponents associated with the system. Forexample, a ball valve, a component ...

WARRANTY/DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for aperiod of 13 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping ...