Omega DPS3300 - Manuals

Omega DPS3300 – Manual in PDF format online.

Manuals:

Manual

Manual Omega DPS3300

Summary

Page 4 - SPECIFICATIONS

Page 3 SPECIFICATIONS (Typical @ 25C and rated supply voltage unless otherwise specified) STANDARD INPUTS * 4-20ma 0-50ma 0-5Vdc 0-10Vdc * Thermocouple inputs: J, K, T, E, R, S, and B * Cold junction compensation error: +/- 1C (10C to 40C) * Open input indication: HELP displayed * Temperature displa...

Page 5 - NOTE

Page 4 NOTE DPS3304 & DPS3314 are four channel units. Therefore, any reference to channel numbers with respect to these models is for channels 1 through 4 only. DPS3307 and DPS3317 are seven channel units, and therefore, any reference to channel numbers for these models is for channels 1 through...

Page 7 - DISPLAYING PARAMETERS; Table 1. How to Display Parameters

Page 6 DISPLAYING PARAMETERS DPS3300 Series keeps track of various parameters and these may be displayed by pushing appropriate keys on the front panel. The parameters that are tracked are: a) Channel's high peak d) Channel with the lowest reading b) Channel's low peak e) Process deviation of each c...

Page 10 - Types of Deviation Displays; Difference Mode; SETUP

Page 9 Deviation Mode In deviation display mode, DPS3300 Series will show the differential between a pre-programmed setpoint and process variable being monitored on each channel by the scanner. Individual setpoint for each channel is programmed during CH Setup and can be any value over the range of ...

Page 11 - CH Parameter List

Page 10 To get into SETUP mode, push the SETUP key twice. The first push displays elapsed time and the second push brings the unit into the SETUP mode. SETUP mode is indicated by 'SETUP' in the display window (the SETUP LED indicator will also be illuminated) followed by 'ENtR PC' (for ENt e R P ass...

Page 12 - CHANNEL CONFIGURATION; Setup For Input Type; Setup for Voltage or Current Input:; Setup For Channel ON/OFF

Page 11 NOTE: To exit from any point during SETUP procedure or to save the newly made changes, simply press and hold the RESET key until the display shows 'SAVING'. When the display shows 'SAVING', it is indicating that the unchanged and the newly made changes are being saved in the EEPROM for perma...

Page 15 - Setup For Engineering Units

Page 14 When this parameter is set for "Normally Open", the relay is open when it is deactivated (readings are below LIMIT), and closes when the channel reading exceeds its LIMIT value. When this parameter is set for "Normally Closed", the relay is closed when it is deactivated (read...

Page 16 - Setup Examples; Example #2: Use of the LOW SCALE Parameter; SYSTEM CONFIGURATION; Setup For Display Options; Table 3. Display Options

Page 15 Setup Examples Example #1: Use of the OFFSET Parameter Setup for a 4-20ma transducer signal corresponding to 0-500 gallons of fluid (reading in 10th of a gallon resolution): DECIMAL POINT = 999.9 HIGH SCALE = 500.0 LOW SCALE = 000.0 OFFSET = 4.000 TARE = 0.000 Example #2: Use of the LOW SCAL...

Page 18 - Setup For Channel Calibration; Voltage Range Setup (for millivolt inputs); Thermocouple Calibration Procedure

Page 17 Setup For Channel Calibration After setting the Cold Junction Reference temperature, the next step is a display of channels for calibration purposes. This allows easy calibration of each channel without the instrument scanning to the next channel. The display will show the channel input read...

Page 19 - PEAKS

Page 18 3. Adjust the gain pot of the instrument until the display reads '1100' . 4. Short channel #1's input with a wire or shorting bar. 5. Push DIFF key. The display will read '0002' --- or some other value. 6. Adjust offset pot of instrument until the display reads '0000' . 7. Push SETUP key -- ...

Page 20 - PROGRAMMING FLOW CHARTS:

Page 19 Once the desired channel has been selected, push 'HI/LO' key. Pushing it once will show the high peak attained by the selected channel. Pushing it a second time will indicate the low process value (NOTE: The second push, to display valley, must be initiated before the display reverts to norm...

Page 23 - Open Collector Option; Figure 1. Open Collector Hookup Example; Electro-Mechanical Relay Option; Figure 2. Electro-mechanical Relays Hookup Example; Instrument

Page 22 RATE DPS3300 series tracks the rate of process change/minute for each channel. This rate is displayed by first pushing the CH. SEL key to select the channel whose rate is desired. Once the channel has been selected, push DATA key. The display will briefly read 'cx-rate' (x=channel #), and th...

Page 25 - DOUBLE CHECK THE CONNECTIONS BEFORE APPLYING POWER!!

Page 24 8 9 10 11 12 13 6 5 4 3 2 1 7 14 POWER Power connection should be made to the three terminal connector as shown in figure 3. Also, make note that it is very important that the power line inputs and the power ground are not switched. Doing so will permanently damage the instrument. Refer to F...

Page 27 - TROUBLE SHOOTING; Factory Channel settings:

Page 26 TROUBLE SHOOTING If the meter locks on a particular display, unplug and plug in again to unlock the display. A total reset clears the memory and defaults all values to zero. To perform this reset, re-apply power with RESET key pressed in. Factory Channel settings: To obtain factory preset va...

Page 28 - MOUNTING; Figure - 4. Rear View And Mounting Hole Locations

Page 27 MOUNTING Figure - 4. Rear View And Mounting Hole Locations 120mm 4.72” 151mm 5.94” SLOTS IN TERMINAL COMPARTMENT FOR MOUNTING SCREWS MOUNTING SCREW SLOTS PICTURE HANGING-TYPE FIXTURE FOR MOUNTING SCREW

Page 29 - WARRANTY