Omega DPS3100 - Manuals

Omega DPS3100 – Manual in PDF format online.

Manuals:

Manual

Manual Omega DPS3100

Summary

Page 4 - SPECIFICATIONS

Page 3 SPECIFICATIONS (Typical @ 25C and rated supply voltage unless otherwise specified) STANDARD INPUTS * 4-20ma 10-50ma 0-5Vdc 0-10Vdc * Thermocouple inputs: J,K,T,E,R,S,B * Cold junction compensation error: +/- 1C (10C to 40C) * Open input indication: HELP displayed * Temperature displayable in ...

Page 5 - NOTE

Page 4 DESCRIPTION DPS3000 Series instruments are multi-channel scanners that pack a number of functions into one unit. Tasks that require multiple monitors can now be accomplished by using only a single unit. Signals from a number of different transducers can be brought into screw terminals that ar...

Page 6 - DISPLAYING PARAMETERS; Table 1. How to Display Parameters

Page 5 DISPLAYING PARAMETERS DPS3000 Series keeps track of various parameters and these may be displayed by pushing appropriate keys on the front panel. The parameters that are tracked are: a) Channel's high peak d) Channel with the lowest reading b) Channel's low peak e) Process deviation of each c...

Page 7 - Scan Mode

Page 6 setpoint, difference between any two selected channels or just run as a timer. In the timer mode the unit keeps track of process run time with crystal controlled accuracy. Elapsed Time display format is 'HH.MM.SS' for hours, minutes, and seconds. The desired display mode is selected during SY...

Page 8 - Types of Deviation Displays

Page 7 Display time for each channel is programmable from 1-999 seconds (16.65 min.). This is useful for adjusting display time to a rate which is consistent with the type of process being monitored. Scan time for each channel is independent of display time. This permits programming long display tim...

Page 9 - Difference Mode; SETUP

Page 8 a) The first one is a momentary display in which the deviation is indicated for a short time. Following this brief display time, the unit reverts to its normal mode of operation (scanning, differential, timer etc.). To achieve this, first select the channel whose setpoint deviation is desired...

Page 10 - CH Parameter List

Page 9 Once the correct pass-code has been entered, the display shows 'SYS CH' , with 'CH' blinking. At this point the operator may choose between making channel settings (CH), or system settings (SYS). Use ^v key to toggle between CH and SYS modes. When the desired mode is blinking, press SETUP key...

Page 11 - CHANNEL CONFIGURATION; Setup For Input Type; Setup for Voltage or Current Input:; Setup For Channel ON/OFF

Page 10 CHANNEL CONFIGURATION After entering correct pass-code and selecting the blinking 'CH' (ref. SETUP section), the display shows 'SLCt CH' (for "Select Channel"). Use ^v key to display the desired channel. Selected channel will be displayed in the format 'CHANEL x' (where x=channel#). ...

Page 13 - Setup for Universal Relay (Channel 1 Relay); Setup For Limits; Setup For Deadband; Setup For Relay Normally Open/Closed

Page 12 SETPOINT value. Once the desired SETPOINT value is displayed, push SETUP key to enter that value and go on to setup channel 1's operational mode. Setup for Universal Relay (Channel 1 Relay) Channel 1 relay can be configured to work as a universal relay or as Channel 1 relay only. In universa...

Page 14 - Setup For Engineering Units; Setup Examples

Page 13 Setup For Engineering Units After setting a channel's relay for NORMALLY OPEN/CLOSED operation, the next parameter to be set are the 3 letters that follow the process value in the display. These 3 letters represent the measurement units for that particular channel. Any desired combination of...

Page 15 - Example #2: Use of the LOW SCALE Parameter; SYSTEM CONFIGURATION; Setup For Display Options; Table 3. Display Options; Setup For Display Time

Page 14 Example #2: Use of the LOW SCALE Parameter Setup for a 4-20ma transducer signal corresponding to 500-2000 degrees Fahrenheit temperature i.e. 500 degrees at 4ma and 2000 degrees at 20ma (one degree resolution): DECIMAL POINT = 9999 HIGH SCALE = 2000 LOW SCALE = 500 OFFSET = 4.00 TARE = 0.000...

Page 16 - Setup for Buzzer; Setup For Channel Calibration

Page 15 Setup For Relay Latch/Non-Latch After setting DISPLAY TIME, the next parameter determines whether the output relays will operate in a Latched or Non-Latched mode. Relay Latched Mode: In this mode the relay is activated when its LIMIT value is exceeded and stays activated until the operator m...

Page 17 - Thermocouple Calibration Procedure

Page 16 desired value is displayed, push SETUP key to enter that value and go to the next step. Voltage Range Setup (for millivolt inputs) For Millivolt input units, the display first shows 'HV rnGE' (for "High Voltage Range"). After the High Voltage range is set, the display shows 'LV rnGE'...

Page 18 - PEAKS; PROGRAMMING FLOW CHARTS:

Page 17 PEAKS A very useful function of DPS3000 is tracking the highest (peak) and the lowest (valley ) point attained by each channel. This is particularly helpful if an operation is not being constantly watched or is left unattended (e.g. overnight). Since high and low points for each channel are ...

Page 21 - Open Collector Option; Figure 1. Open Collector Hookup Example; Electro-Mechanical Relay Option; Figure 2. Electro-mechanical Relays Hookup Example

Page 20 RATE DPS3000 series tracks the rate of process change/minute for each channel. This rate is displayed by first pushing the CH. SEL key to select the channel whose rate is desired. Once the channel has been selected, push rate key. The display will briefly read 'cx-rate' (x=channel #), and th...

Page 22 - DOUBLE CHECK THE CONNECTIONS BEFORE APPLYING POWER!!

Page 21 NOTE: LOOK UNDER SPECIFICATIONS FOR THE RATING ON RELAYS AND OPEN COLLECTOR OUTPUTS. UNDER NO CONDITION SHOULD THE RELAYS AND OPEN COLLECTOR OUTPUTS BE OPERATED BEYOND THEIR RATED CAPACITY. DOING SO CAN DAMAGE THE UNIT PERMANENTLY. The status of the relays for all the channels is indicated o...

Page 23 - OUTPUT CONNECTOR PIN ASSIGNMENT

Page 22 1 2 3 4 6 5 7 8 9 10 11 12 13 14 OUTPUT CONNECTOR PIN ASSIGNMENT - + - + - + - + - + - + - + Table 1. DPS3000 Series Output Connector Pin Assignments OUT-PUT CONNECTOR PIN ASSIGNMENTS Pin # Signal Relay Output Open Collector 1 Channel #1 Limit Common Positive Output 2 Channel #1 Limit Normal...

Page 24 - TROUBLE SHOOTING; Factory Channel settings:

Page 23 TROUBLE SHOOTING If the meter locks on a particular display, unplug and plug in again to unlock the display. A total reset defaults all scaling values to zero. To perform this reset, re-apply power with RESET key pressed in. Factory Channel settings: To obtain factory preset values simply re...

Page 25 - MOUNTING; Figure - 4. Panel Cutout and mounting hole dimensions

Page 24 MOUNTING 3.70” (94mm) 4.05 ” (10 2.87 mm) 1.77” (45mm) 0.15” dia. (3.81mm) Figure - 4. Panel Cutout and mounting hole dimensions 1. Cut out Panel and mounting hole dimensions as shown in the figure 8. 2. Remove the nuts from the mounting screws on the Panel Meter. 3. Insert panel meter into ...

Page 26 - WARRANTY

Page 25 WARRANTY For Warranty information, check Omega’s web site at http://www.omega.com