Omega DP3001 - Manuals

Omega DP3001 – Manual in PDF format online.

Manuals:

Manual

Manual Omega DP3001

Summary

Page 3 - TABLE OF CONTENTS

i TABLE OF CONTENTS SAFETY CONSIDERATIONS ......................................................................................... iii 1.0 GENERAL INFORMATION ........................................................................................ 1 2.0 SPECIFICATIONS .................................

Page 4 - ii

ii LIST OF FIGURES: Figure 3.1 DIN Case Dimensions .................................................................................. 4Figure 3.2 Exploded View .............................................................................................. 5Figure 4.1 Side View of Transformer ...........

Page 5 - iii; SAFETY CONSIDERATIONS

iii SAFETY CONSIDERATIONS This device is marked with the international Caution symbol. It is important to read this manual before installing or commissioning this device as it contains important information relating to Safety and EMC (Electromagnetic Compatibility). Unpacking & Inspection Unpack...

Page 10 - enough to hold the case in place. Never over-tighten clamp screws.

4 Figure 3.2 Exploded View 3.2 PANEL MOUNTING 1. Remove main board connector J1, if installed. Loosen the two clamp screws (with a #8 Phillips screwdriver) on the rear of case and rotate the slide clamps. Push the two slide retainers toward the rear of the unit and remove them. 2. Working from the f...

Page 11 - POWER AND SIGNAL; Refer to Safety Considerations prior to connecting power.; CHANGING OPERATING VOLTAGE; exist between analog and digital grounds on connector J1.; Input

5 4.0 POWER AND SIGNAL AC versions of the voltmeter are factory-set for 115 Vac in the USA and 230 Vac in Europe (using C1 option) ±15% operation. DC versions are preset for 9-32 Vdc or 26-56 Vdc operation. It is not possible to change the meter from 9-32 Vdc to 26-56 Vdc or vice versa. Different st...

Page 12 - Rear Terminal Hookups; Wire Color for AC Power USA; Model

6 Figure 4.2 Rear Terminal Hookups Wire Color for AC Power USA Other (High) Black Brown (Low) White Blue (Ground) Green Green Model Power Signal AC D1 Connector A High 17 High 2 Low 16 Low C Earth Ground T Analog Ground D4 Connector 1 High 6 High 2 Low 5 Low 3 Earth Ground 4 Analog Ground DC D1 Conn...

Page 13 - MAIN BOARD PIN ASSIGNMENTS (J1 Card Edge); Left to right, looking at rear of case; P1 Connection

7 4.3 MAIN BOARD PIN ASSIGNMENTS (J1 Card Edge) Left to right, looking at rear of case P1 Connection Standard A Spare (E16) 1 No connection B No connection 2 Spare (E18) C Spare (E19) 3 No connection D No connection 4 No connection E Spare (E43) 5 No connection F 1999.9 (DP4) 6 Spare (E24) H 199.99 ...

Page 14 - SIGNAL INPUTS; Signal Voltage

8 4.4 SIGNAL INPUTS RATIO: The reference input allows an external voltage to be used as the reference source for conversion. In this mode, the meter reads the ratio of the signal voltage to the reference voltage rather than the true value of the input. Signal Voltage Reading in Counts = Reference Vo...

Page 15 - Connect K to L

9 5.0 CONFIGURATION Select the desired configurations from the following charts. Install jumpers and open/close solder switches as indicated. Remove all push-on jumpers not used. 5.1 DECIMAL POINT SELECTION Figure 5.1 Display Board Jumper Locations Decimal Point S1 Alternate decimal point configurat...

Page 17 - Figure 5.3 Solder Switch Locations; Solder switch F is used for reference input impedance ratio.; Section 4 for more information.; bottom of the lens and gently pry it off.

11 Figure 5.3 Solder Switch Locations Solder switch F is used for reference input impedance ratio. Refer to Section 4 for more information. 6.0 CALIBRATION This unit was factory-calibrated with a precision voltage source. Frequent calibration is not necessary due to the stability and internal accura...

Page 18 - Assembly Diagram, Main and Display Board

12 7.0 DRAWINGS Figure 7.1 Assembly Diagram, Main and Display Board

Page 19 - Dual-slope Conversion Diagram

13 8.0 DUAL-SLOPE CONVERSION At the beginning of a conversion, the voltage across C int is zero. The signal is then applied to the integrator and the voltage across C int rises by the formula: T1 E Cint = Esig R int C int At the end of a fixed period of 10000 counts, T1, the counters are reset to 00...

Page 20 - NOTES

NOTES ______________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ _________________________________________________________...

Page 23 - RETURN REQUESTS/INQUIRIES

WARRANTY/DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of one (1) year from the date of purchase. In addition to OMEGA’s standard warranty period, OMEGA Engineering will extend the warranty period for one (1) additional year if ...

Page 24 - Shop on line at omega.com

M5280/1112 11119ML-99J Where Do I Find Everything I Need for Process Measurement and Control? OMEGA…Of Course! Shop on line at omega.com TEMPERATURE R Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies R Wire: Thermocouple, RTD & Thermistor R Calibrators & Ice Poi...