Nuvo NV-USBW - Manuals - manualsarea.com

Page 3 - FCC Radio Frequency Interference Statement Warning; IC Statement; This Class B digital apparatus complies with Canadian ICES-003.

EN55022 Class-B EN55024 FCC Radio Frequency Interference Statement Warning IC Statement This Class B digital apparatus complies with Canadian ICES-003. This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits a...

Page 4 - Introduction; Table of Contents; Page 3; NV-USBW Package Contents

Introduction Congratulations on your purchase of the NuVo NV-M3 audio server and the new NV-USBW wireless USB extender from Silex. The M3 is unique in its ability to easily sync with Window’s Media Player with a single USB connection. The new NV-USBW is a wonderful tool for enabling multiple compute...

Page 8 - Figure 4 – Selecting “Setup Device Server from PC by wireless LAN”; Left-click “Yes” to accept the Silex Software License Agreement.

6 (6) The screen shown in Figure 4 will come up. Make certain that “Setup device server from PC” is the default setting. Then, left-click “Next”. Figure 4 – Selecting “Setup Device Server from PC by wireless LAN” ( 7 ) Left-click “Yes” to accept the Silex Software License Agreement. (8) A status win...

Page 10 - of the “What You Need for Setup” section.; Figure 7 – “Setting TCP/IP” Window

8 If the selection window shown in Figure 6 does not come up, but a “Confirm Configuration Parameters” window comes up instead at this point, the wireless PC you are using has failed to locate the Device Server. (a) Double-check to make sure that the Device Server is physically located as explained ...

Page 11 - Figure 8 – “Searching for Access Point ...” status

9 (11) The status screen shown in Figure 8 will come up. Figure 8 – “Searching for Access Point …” status ( 12 ) After a short wait, the wireless network setting window shown in Figure 9 will come up. Select the user's wireless network, which will show “Infrastructure” under the “Wireless Mode” colu...

Page 12 - Figure 9 – Wireless Network (SSID) selection window

10 Figure 9 – Wireless Network (SSID) selection window ( 13 ) The window shown in Figure 10 will come up. Left-click the “Execute” button. Make certain that: (a) The Wireless Mode is set to “Infrastructure”(b) The SSID corresponds with the name of your user's network(c) Network Authentication is set...

Page 16 - ) Left-click “Yes” to accept the Silex Software License Agreement.; Figure 14 – Device Server Search Window

14 ( 6) Left-click “Yes” to accept the Silex Software License Agreement. (7) The Device Server Search window will come up. If you already see a device in the Search result overview panel as shown in Figure 14, left-click the device to select it, and then left-click “Next”. If there is no device show...

Page 17 - (9) The status window shown in Figure 16 will come up.; Figure 16 – “Searching for Access Point ...” status

15 Figure 15 - “Setting TCP/IP” Window (9) The status window shown in Figure 16 will come up. Figure 16 – “Searching for Access Point …” status

Page 18 - Figure 17 – Skipping the wireless configuration

16 After the Access Point Search completes, you will get the window shown in Figure 17. Check the “Skip wireless configuration” box in the lower left, and all settings for wireless will “gray out”. You are setting up for wired operation only, and do not need to configure them. Left-click “Next”. Fig...

Page 19 - Figure 18 - Confirm Configuration Parameters window

17 Figure 18 - Confirm Configuration Parameters window ( 10 ) The Device Server Setup Complete window shown in Figure 19 should come up.If you are using the user's PC for setup at this point, left-click “Yes” for the “Do you want to install SX Virtual Link” question decision in the window, and then ...

Page 20 - Figure 19 – Setup Complete status window

Page 22 - Figure 21 – Device Server List, no NV-M3 connected

20 Figure 21 – Device Server List, no NV-M3 connected ( 3 ) Make sure that the NuVo NV-M3 is plugged into an AC outlet and blue STANDBY LED is lit. Connect the NV-M3 to the device server using the supplied USB cable. A “+” icon should appear in the box to the left of the Device Server list entry. Le...

Page 24 - Figure 24 – Portable Device handling decision window

22 ( 5 ) A “Portable Device” decision window as shown in Figure 24 should pop up if you do not have Windows Media Player open already. Select the “Sync” icon as shown in the Figure, and left-click “OK”. Windows Media Player will open and search for the device for a few moments, and then you should s...

Page 25 - Figure 25 – Disconnect confirmation

23 Figure 25 – Disconnect confirmation ( 7 ) Select the box next to the “Do not display a confirmation message before disconnecting”, so this won't occur anymore, and then left-click the “Yes” button. You will see a disconnect status message as shown in Figure 26, which will go away. ( 8 ) Now, if y...

Page 28 - NuVo Technologies

NuVo Technologies 3015 Kustom Dr., Hebron, KY 41048 859-817-7200 www.nuvotechnologies.com USBW0745