Nuvo 110 - Manual - manualsarea.com

Page 2 - BEFORE YOU START; Never; READ BEFORE YOU START

~ 2 ~ ~ 3 ~ 1. LOCATING YOUR WINE CELLAR - Remember, it is not an appliance, it is a piece of furniture 2. AREA FOR ASSEMBLING YOUR WINE CELLAR Choose a clear 12’ by 12’ area with a level floor and carpeting to help reduce scratching of surfaces. 3. TOOLS * Hex wrench (included) * Phillips screwdriv...

Page 3 - HARDWARE KIT; Hardware quantities for Model 220 are indicated in parenthesis.

~ 2 ~ ~ 3 ~ HARDWARE KIT C B A F E G D H *NOTE : Hardware quantities for Model 220 are indicated in parenthesis. Cam Cap x 20 (x24)* Hex Bolt x 14 Hex Wrench x 1 Cam x 20 (x24)* Cam Pin x 20 (x24)* Leg x 4 In Cooling Unit Box Hex Bolt (Flange) x 2 Panel Insulation Strip x 1

Page 4 - STEP 1 : PANEL PREPARATION; TAB

~ 4 ~ ~ 5 ~ STEP 1 : PANEL PREPARATION 1 PANEL EDGE H CAUTION : 1. Watch for sharp staples on boxes.2. DO NOT STEP ON PANELS3 . The manual will give a recommended order to open boxes, it saves space and time. 2 H ! Open Box VP1. Install INSULATION STRIP (H) to Back, Top, and Bottom Panels. PUSH IN F...

Page 5 - STEP 2 : CABINET ASSEMBLY; BOTT; MET

~ 4 ~ ~ 5 ~ STEP 2 : CABINET ASSEMBLY Attach Top and Bottom to Back by CAREFULLY aligning edge holes over Cam Pins and gently push together to avoid damaging cam pins. DO NOT BANG OR SLAP PANELS TOGETHER!!! Insert Cam, push all the way in under panel level (may require some force) and make sure Arro...

Page 6 - STEP 2 : CABINET ASSEMBLY CONTINUED

~ 6 ~ ~ 7 ~ STEP 2 : CABINET ASSEMBLY CONTINUED CHECK PANEL ORIENTATION !!! Open Box VP5 or VP2. Insert Cam Pins (E) into SIDE PANEL’S predrilled holes both sides down to TAB. (May require some force) Attach SIDES to Back/Bottom/Top by Carefully aligning edge holes over Cam Pins and gently push toge...

Page 7 - STEP 3 : HINGE,BASE AND LEGS INSTALLATION

~ 6 ~ ~ 7 ~ Fasten BASE with HEX BOLTS (B) 4 C A B I N ET BOTT OM FRONT BASE 1 3 4 STEP 3 : HINGE,BASE AND LEGS INSTALLATION Raise cabinet and check for potential air leaks at panel joints from inside. 2 Install four LEGS (F) into BASES fully in. 3 Open Box VP3. Fasten one HINGE (found in door box) ...

Page 9 - STEP 5 : COOLING UNIT INSTALLATION; GET HELP; bolts in; KEEP UNIT LEVEL; CHECK

~ 8 ~ ~ 9 ~ LEVEL TO OPENING STEP 5 : COOLING UNIT INSTALLATION GET HELP BEFORE INSTALLING AND KEEP CHILDREN CLEAR OF CELLAR CONSTRUCTION AREA. Get helper to help guide unit, keep light cord clear of edge inside cellar and to prevent tipping of cellar. MAKE SURE INSULATION STRIP IS IN CORRECT ORIENT...

Page 10 - STEP 6 : LIGHT AND LIGHT COVER INSTALLATION

~ 10 ~ ~ 11 ~ 3 Insert LIGHT COVER to holes pre drilled on front edge of TOP panel. STEP 6 : LIGHT AND LIGHT COVER INSTALLATION 1 Plug cord to LIGHT 2 Insert LIGHT to LIGHT COVER

Page 11 - STEP 7 : DOOR INSTALLATION

~ 10 ~ ~ 11 ~ Install TOP HINGE with HEX BOLTS (B) NOTE : Adjust final position of the door before tightening the bolts and move cellar into place, leaving 4” clearance all around cellar. MAKE SURE CABINET IS AIRTIGHT! Adjust the level by turning (counter clockwise) the LEGS (F) as needed. Use a car...

Page 12 - CONTROLS : PLUG IT IN; KEYS; A L

~ 13 ~ FEATURES: - Default SET temperature 57º F/14º C (ideal for wine storage). - Calibration option of the temperature sensor. - Display of actual temperature by request. - SET temperature range 52ºF-64ºF. - Digital temperature sensor. - Dual display Fº/Cº. - Settings are stored in memory for powe...

Page 13 - MAXIMUM CAPACITIES AND LOADING TIPS

~ 13 ~ MAXIMUM CAPACITIES AND LOADING TIPS Maximum capacities and sample loading arrangements for Vintage Keeper Tuscany wine cellars are illustrated below. Note the variations in shelf height, to accommodate the widest variety of bottle types and sizes. Standard Burgundy and Bordeaux bottles are be...

Page 14 - TROUBLE SHOOTING GUIDE

TROUBLE SHOOTING GUIDE Although each Vintage Keeper cooling unit has been carefully tested at every stage of manufacture, occasional problems arise, the majority of which are due to rough or careless handling during shipping or installation. Other problems may derive from improper cabinet assembly, ...

Page 15 - LIMITED WARRANTY AND PRODUCT SUPPORT

LIMITED WARRANTY AND PRODUCT SUPPORT ONE YEAR LIMITED WARRANTY If your Koolspace cooling unit or cabinet fails to perform as designed within one year of the date of purchase, VINTAGE KEEPER INC. warrants that, upon your request, it will be repaired or replaced, at our option, during the one year war...

Page 16 - C E L L A R; nuvo

Toll free: 1-888-274-8813 www.koolspace.com 1 1 0 / 2 2 0 C E L L A R nuvo k o o l s pa c e TM

Nuvo 110 - Manual

Table of Contents:

Summary

Other Nuvo Models