Nuvo NV-T2FX - Manuals

NV-T2DF Wiring Diagram Diagram is shown with the NuVo Concerto System and NuVoNet. NV-T2DF Package Contents: 1 NV-T2DF Dual AM, FM, WX Tuner 1 NV-T2FAA Active AM/FM Antenna1 NV-T2RC3 Remote Control2 NV-RCA1 Stereo RCA Audio Cables1 NV-AC1 2 Meter Coaxial Antenna Cable1 NV-PC2 IEC 2-Wire Power Cable ...

Front Panel 1. Stand-by LED: This LED (Light Emitting Diode) indicates that the T2 is plugged into an AC power source. 2. Remote Sensor: This IR (Infrared) receiver allows wireless remote control of the T2 functions. This IR input is active, even when it is used in conjunction with the direct IR inp...

Back Panel 1. Antenna Input: Coax “F” connector brings in the signal input from the NuVo NV-T2FAA AM/FM or the NV-T2XAA XM active antenna (pg. 11). 2. Aux. Input: This stereo RCA connector is enabled through the advanced menu options (pg. 14), and allows an additional audio source to be connected an...

NV-T2RC3 Remote Control 1. Power: The power button turns the selected tuner on and off. 2. Scroll Buttons: These buttons are the equivalent of turning the front panel Select knob. The top button is the equivalent of turning the knob clockwise, and the bottom button is the equivalent of counterclockw...

IR Pass-Thru The mini jack labeled “IR pass-thru" mini connection is used for connecting forwarded IR signals to an audio component connected to the auxiliary audio input. Using the Aux. Input The T2 is equipped with an auxiliary audio input labeled “AUX IN.” This will accept an audio signal fro...

AM/FM Antenna Input The T2 ships with a proprietary active AM/FM antenna. This antenna is designed to work only with the NuVo T2 series AM/FM tuners. It can be located up to 200 feet from the tuner location, and we recommend 75-ohm RG 6 coaxial cable with a standard F style connector on each end. Si...

Page 12 Proper Location of the XM Antenna Location of the XM antenna is critical to proper performance. There cannot be any obstructions between the antenna and the southern sky. This means that any possible interference from buildings, trees or other structures must be avoided. The most common loca...

II. Front Panel Menu Controls AM/FM The T2 has many settings available in the menus. This allows for specialized set up options for tuner operation. The menu is accessed from the front panel by pressing and holding the “MENU” button. Once in menu mode, you can scroll through the menu options by turn...

The following menu selections are not necessary for standard tuner operation, but do provide a deeper level of control for those who need it. When you scroll to “Advanced Settings” in the menu, pressing the Select knob then accesses the following menu options: Operating Mode The T2 defaults to Stand...

Audio Settings These selections are intended for AM, FM and XM stand-alone applications. They should be left at default settings for NuVo audio systems. These systems allow identical audio control on a per-zone basis. Bass EQ: Bass output can be adjusted +12 dB or down to 12 dB. The default setting ...

AUX Input Disable/Enable: The T2 has an auxiliary audio input that allows access through either of the tuners to an additional audio source. To use this you must first enable the input in the menu options. AUX Gain: The audio input from an auxiliary source can be adjusted to match the output of the ...

Page 17 III. Front Panel Menu Controls XM Most menu functions are identical to the AM/FM tuner with some exceptions. The menu functions specific to XM reception are outlined here. Signal Status: This function is important to XM functionality. When the antenna is installed and plugged into the T2 ant...

IV. Stand-alone Front Panel Use of the T2 Tuning a Desired Station: Pressing the Select knob cycles through the tuning modes. Step Tune Mode: Each of the T2's tuners default to step tune mode. When the Select knob is turned clockwise (CW), the tuner will tune within the preset tuning standard ( see ...

Actual use of these data fields is not regulated, and they may vary significantly in content between stations. If you choose not to have RDS information displayed, pressing the “Display” button will then indicate “RDS receive OFF”. In this state, Stereo indication and a signal strength indicator wil...

IV. Using the T2 with the Concerto NuVoNet Setting Up the Tuner for NuVoNet The T2 must be set for one of the Concerto source inputs 1-6. This can be done at the front panel when the tuner is first turned on, in the T2 Configurator software, or through the front panel advanced menu. The best way to ...

Making the Connection Prior to connecting to NuVoNet, the Concerto must have the correct Configuration version downloaded with the T2 representing two of the audio sources. Making the NuVoNet connection is done simply by connecting the “NuVoNet” output on the T2 to one of the “Peripheral Device” inp...

T2 AM/FM Configuration Software Basic setup and operation of the T2 is easily done from the front panel, the included T2RC3 remote, or the Concerto Display Pad. The T2 package includes the T2 Configurator setup software designed to quickly move you through the Tuners' setup options in a methodical f...

2.2 Regional Setup 2.3 Brightness 2.4 Auto-On Page 23 2.2 Regional Setup: Depending on your geographic location, the tuner needs to be set for the proper tuning standard. The choices are USA and Canada, Western Europe, Australia, and New Zealand. Countries outside these geographic locations need the...

3.3 Rename Bank 3.4 Erase Bank 3.2 Add Bank Page 24 3.2 Add Bank: If you want to add a bank of 10 presets, the “Add Bank “ button will bring up a window that allows you to name the bank and automatically add it to the T2's presets. 3.3 Rename Bank: This button allows you to give a bank of presets a ...

4.1 Custom Regional Setup Page 25 4.1 Custom Regional Setup: Some countries operate at a tuning standard outside the four preset regions. The Custom setting allows specific parameters. One determining factor for tuning is the “Pre-emphasis”. The two choices for this a are 50µS (microseconds) and 75µ...

4.5 AUX Input Page 26 4.5 AUX Input: The T2 has an additional input that allows an external device to be controlled through the T2's IR pass through. When this input is enabled, the level of the signal input can be adjusted up or down to match the tuners' signal output level. 5.0 Advanced Presets Th...

Page 27 6.1 Categories Tab 6.2 FM Freqs: This tab lists all the available frequencies within the FM band. When highlighted, the Frequency Information on the right side of the tab allows you to name and categorize each desired frequency in up to four different categories. The Category drop down menus...

Page 28 7.2 Successful Download: When the download is complete a final window will appear indicating that all the information has downloaded successfully. Actual download time will vary based on your computer's processing capabilities. 7.2 Successful Download Troubleshooting Symptom I can't control ...

NV-T2DF Specifications FM Section AM Section Tuning Range 87.5 to 108 MHz Tuning Range 522 to 1720 kHz IF Frequency 10.7 MHz IF Frequency 450 kHz Usable Sensitivity, 30 dB S/N 14 dB ?V Usable Sensitivity 25 dB S/N Auto Scan Sensitivity Adjustable Auto Scan Sensitivity Adjustable Image Rejection 50 d...