Nuvo NV-E6MS - Manuals

LINE OUT L LINE OUT / SPEAKER LINE OUT LINE OUT LINE OUT LINE OUT LINE OUT ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 20W/8 OHM X2 20W/8 OHM X2 20W/8 OHM X2 20W/8 OHM X2 20W/8 OHM X2 20W/8 OHM X2 R L R L R L R L R L R LEFT - + RIGHT - + LEFT - + RIGHT - + LEFT - + RIGHT - + LEFT - + RIGHT - + LEFT - ...

VOL VOL TUN3 TUN2 TUN1 SAT CD2 CD1 MUTE ON•OFF ALL OFF Page 4 The E Series keypad comes with four molded, replaceable covers in white, ivory, almond, and black. The selected source button remains a backlit green until a new source is selected or the zone is turned off. A flashing source button indic...

OFF ON AM FM MON ST _ + _ + MUTE ON-OFF ALL OFF MEM 0 NUM 8 9 7 5 6 4 2 3 1 TUNER 1TUNER 2TUNER 3 TUNER MULTI-ROOM Power Tune Preset VOL VOL TUNER MULTI ROOM Source 1 Source 2 Source 3 Source 4 Source 5 Source 6 Source 7 Source 8 Source 9 Source 10 Mode Band NV-RC1 Device Selector: Numeric Keypad: A...

1 2 3 4 5 6 7 8 Pair 2 Pair 1 Pair 4 Pair 3 Page 6 INSTALLING YOUR E SERIES SYSTEM I. Installing and Terminating Cables The basic installation requires two different types of cables. The keypads communicate with the E6M amplifier through Cat-5 data cable (4 twisted-pair). This cable is terminated at...

Fig. 2: E-Z Port Backside Page 7 The location of the E-Z Port is mostly determined by where you locate the E6M amplifier. All Cat-5 cables should be terminated and routed to this location. Once this is done, installation of the E-Z Port is easy. Plug each of the keypad cables into one of fifteen ava...

IR EMITTER OUTPUTS +12V OUTPUT PULSE SUM AUDIO OUTPUT CONNECT TO NV-E6X ODD NUMBERED OUTPUTS ARE IDENTICAL (TIED TOGETHER) EVEN NUMBERED OUTPUTS ARE IDENTICAL (TIED TOGETHER) Page 8 1 2 3 4 5 6 Each piece of source equipment is connected to the E6M amplifier with RCA cables. These go from the RCA ou...

VI. Connecting the E6M to the E6X Page 9 * FOR SECOND KEYPAD 1000 0100 1100 0010 1010 1 2 3 4 5 00 01 10 11 B,T+4 100+4 10K+4 FLAT 0 1 ON OFF 0 1 ON OFF SW # 1,2,3,4 ZN# SRCE GROUP 0110 1110 0001 1001 0101 1101 0011 1011 0111 1111 6 7 8 9 10 11 12 1* 2* 3* SW 5-6 SETS ZONE EQSW 8 SETS VOLUME RESET S...

1 2 3 4 5 6 7 8 O N 1 2 3 4 5 6 7 8 O N 1 2 3 4 5 6 7 8 O N 1 2 3 4 5 6 7 8 O N 1 2 3 4 5 6 7 8 O N 1 2 3 4 5 6 7 8 O N 1 2 3 4 5 6 7 8 O N 1 2 3 4 5 6 7 8 O N 1 2 3 4 5 6 7 8 O N 1 2 3 4 5 6 7 8 O N 1 2 3 4 5 6 7 8 O N 1 2 3 4 5 6 7 8 O N Page 10 The single most important aspect of the installation...

REFER TO MANUAL 0 1 2 3 DIAGNOSTIC CONTROL -INPUT- -OUTPUT- MUTE UNIT ON +12V G N.O. G X. Using the “Mute” and “Unit On” Pins Page 12 All NUVO products come with the wireless remote. This remote will control all functions of the NV-EKP keypad. To control the E Series, move the “Device Selector” swit...

REFER TO MANUAL 0 1 2 3 DIAGNOSTIC CONTROL -INPUT- -OUTPUT- MUTE UNIT ON +12V G N.O. G Page 13 The MPU Diagnostic LEDs serve several functions. One function is the “lowest assignable address.” This is an aid in sequentially assigning the appropriate address on each keypad. When the system is turned ...

Page 15 Symptom Probable Cause Remedy When a keypad is plugged in, there is a loud “pop” through the speakers and the keypad does not work. Improperly wired Cat-5 cable. Check that you are using the 568A wiring standard (See Section I. “Installing and Terminating Cables”). My keypad is lit, but noth...

Page 16 NUVO NV-E6M Specifications Power Amplifier Section Continuous Average Output Power 23W Two channels driven 30-20kHz @ 1% THD Rated Distortion (1/2 power) 0.4% Rated Impedance 8 Ohms Damping Factor 50+ Line Output Level (at full output) 4.5V RMS Frequency Response (30-20kHz) +/-3dB Preamplifi...