Nutone CV352 - Manuals - manualsarea.com

Page 2 - THE RANCH STYLE HOUSE

2 GENERAL INFORMATION LAYOUT AND PLANNING EXAMPLES The NuTone Central Cleaning System consists of a Central Power Unit, PVC Tubing, PVC Fittings, automatic switchoperated Wall Inlets, a flexible hose and various cleaningattachments. As an aid in planning the installation, look at the following examp...

Page 3 - THE SPLIT-LEVEL HOUSE

3 FIGURE 3 THE SPLIT-LEVEL HOUSE Like the two-story house, the split level installation commonly calls for a two-level trunk line.Here, the power unit islocated in the garage.The intake tubing runsexposed up thegarage wall andinto the ground levelsection's attic. Two branch linesconnect this part of...

Page 4 - INSTALLATION IN NEW CONSTRUCTION; INSTALLATION HINTS; INSTALLING THE TUBING

4 INSTALLATION IN NEW CONSTRUCTION WALL INLET ROUGH-IN 1. Once the locations for wall inlets have been determined, mount all inlet brackets. 2. To locate bracket on wall stud, measure approximately 18" up from finished floor level. (Height may vary according toindividual preference.) 3. Refer to...

Page 5 - TUBING INSTALLATION; NAIL PLATE INSTALLATION

5 FIGURE 7 INCLUDE FITTING RECESS IN MEASUREMENT TUBING MEASUREMENT PVC TUBING FIT TING FIT TING 3 / 4 " 3 / 4 " FIGURE 8 FIGURE 9 FIGURE 10 FIGURE 11 FIGURE 12 TUBING INSTALLATION 1. Cut a 2 1 ⁄ 2 " diameter hole in sole plate, header or stud directly in line with opening of inlet brack...

Page 6 - WALL INLET INSTALLATION

6 FIGURE 15 FIGURE 16 MODEL 365 DOUBLE FLANGED TEE WALL INLET MOUNTING BRACKET SHORTEN WALL FIGURE 13 FIGURE 14 WALL INLET INSTALLATION MODEL 360 WALL INLET(361 Rough in) 1. Once the walls have been finished, install the wall inlets.2. Remove the cardboard plaster guard.3. Refer to Figure 13. For so...

Page 7 - DIMENSIONAL CHART; POWER UNIT INSTALLATION; MOUNTING; TUBING CONNECTIONS

DIMENSIONAL CHART MODEL DIMENSION CV-352 A 27" B 7 3 ⁄ 4 " C 6 1 ⁄ 2 " D 13 5 ⁄ 8 " 7 POWER UNIT INSTALLATION MOUNTING See Figure 18. 1. Locate the power unit within six feet of a grounded electrical outlet. 2. Drill 3 ⁄ 16 " diameter pilot holes for the two (2) mounting screws i...

Page 8 - INSTALLATION IN EXISTING CONSTRUCTION; LAYOUT AND PLANNING

8 INSTALLATION IN EXISTING CONSTRUCTION LAYOUT AND PLANNING The general layout and planning and the component locations are the same for existing construction.See pages 2 and 3. LOCATING ACCESS KEYS Unless your home is a ranch-style house where a single trunk line can run directly through the attic ...

Page 10 - MODEL 330N WALL INLET INSTALLATION; FLOOR INLET INSTALLATION; INSTALLATION IN NEW AND EXISTING CONSTRUCTION

10 MOUNTING PLATE MOUNTING HOLE (2) ELBOW FIGURE 32 MOUNTING PLATE INLET FIGURE 33 1. Make cutout according to dimensions in Figure 30.2. Refer to Figure 31. Break off nail plate at scored line. 3. Refer to Figure 32. Glue elbow to mounting plate, place assembly into cutout, and attach elbow to tubi...

Page 11 - FINAL SYSTEM CHECK

11 FLOOR SUB-FLOOR 2 9 / 16 " 3 1 / 16 " INLET EXTENSION FLOOR INLET FRAME MOUNTING BRACKET SEAL FLANGED FITTING FIGURE 36 CUT TO LENGTH EXTENSION SLEEVE FLANGED FITTING MOUNTING BRACKET FLANGE FIGURE 37 WALL INLET EXTENSION SLEEVE BRACKET FLANGED FITTING TUBING FIGURE 38 FINAL SYSTEM CHECK ...

Page 12 - Two Year Limited Warranty

Product specifications subject to change without notice. Printed in U.S.A., Rev. 4/01, Part No. 84912 Two Year Limited Warranty WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of ...

Nutone CV352 - Manuals

Manuals:

Manual Nutone CV352

Summary

Nutone Manuals